Installation User Manual

ManualsBrandsPeerless-AV ManualsProjectorsPJF2-UNV-S





1 of 9



Installation and Assembly Manual:

Vector Pro II™

Models: PJF2-UNV, PJF2-UNV-S

Maximum UL Load Capacity: 50 lb (27 kg)



This product is intended for use with UL

Listed products and must be installed

by a qualied professional installer.

Summary of content (9 pages)

PAGE 1
Installation and Assembly Manual: Vector Pro II™ Models: PJF2-UNV, PJF2-UNV-S This product is intended for use with UL Listed products and must be installed by a qualified professional installer. Maximum UL Load Capacity: 50 lb (27 kg) 1 of 9 Visit the Peerless Web Site at www.peerlessmounts.com ISSUED: 01-14-09 SHEET #: 056-9018-2 05-18-10 For customer care call 1-800-729-0307 or 708-865-8870.
PAGE 2
Note: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call Peerless customer care at 1-800-729-0307.
PAGE 3
Before you start check the parts list to insure all of the parts shown are included. Parts List Description ball and socket mount adapter plate ceiling plate extension column connector with cord management M5 x .8 x 10 mm socket pin type F screw #10-32 x 3/8" spade thumb screw #10-32 x 3/8" serrated washer head socket pin screw #14 x 2.5 phillips hex head wood screw .25" ID x .56" OD x .
PAGE 4
Installation To Wood Joist Finished Ceilings, Exposed Wood Joists, or Wood Beam Ceilings 1 Drill two 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach ceiling plate (C) with two #14 x 2.5" (6 mm x 65 mm) wood screws (H) as shown using 3/8" (10 mm) socket wrench. Skip to step 3 for flush mount installation. Skip to step 4 for extension column installation. WOOD JOIST CEILING WARNING • Tighten wood screws (H) so that ceiling plate (C) is firmly attached, but do not overtighten.
PAGE 5
WARNING • When installing Peerless wall mounts on concrete, verify that you have a minimum of 1 5/8" of actual concrete surface in the 1/4" diameter hole to be used for the concrete anchors. Do not drill into mortar joints! Concrete must meet ASTM C-90 specifications. • Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
PAGE 6
Flush Mount Application 3 Screw ball and socket mount (A) into ceiling plate (C) as shown in figure 3.1. Align the notch with one of the four holes of the ceiling plate (C) and secure ball and socket mount (A) with a M5 x 10 mm socket pin screw (E) using security allen wrench (U) as shown in figure 3.2 NOTE: Slotted set screw (L) is used to jam against the threads of the ball and socket mount to prevent any excess movement of the ball and socket mount (A).
PAGE 7
Installation to Extension Column 4 C C Screw extension column to ceiling plate (C). Align the notch with one of the four holes in the ceiling plate (C) and secure extension column with a M5 x 10 mm socket pin screw (E) using security allen wrench (U). See figure 4.1 EXTENSION COLUMN (UL Listed EXT or ADJ Series) Sold Separately Screw extension column connector (D) to extension column. Align slot in extension column with one of the top holes in extension column connector (D).
PAGE 8
Attaching Adapter Plate to Projector NOTE: The projector you are installing may differ in appearance from the sample illustrated below. 5 Place projector upside down. Locate adapter plate (B) with notch facing forward as close to projector center of gravity as possible without covering any mounting holes. Loosen channels, and if there are only three mounting holes remove fourth channel. Using one channel for each mounting hole, position feet of channels over mounting holes as shown below.
PAGE 9
Attaching Adapter Plate to Projector Mount 7 Attach projector, with adapter plate (B) already on it, to the ball and socket mount (A) by inserting the ball and socket mount into the adapter plate connection and twisting until the adapter plate will no longer turn (about 75°). The spring loaded captive screw should line up with a corresponding hole on the adapter plate (this should line up automatically when the two are connected).