User's Manual

ManualsBrandsPeerless Industrial Group ManualsTV MountPeerless Industrial Group Industrial Group TV Mount CMJ455

1 of 5

Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-865-2112 or 708-865-8870.

ISSUED: 05-27-99 SHEET #: 128-9103-6 06-21-10

LKF

This Suspended Ceiling Plate is intended for use only to support Projec-

tor Mounts or other products as speciﬁ ed by Peerless.

This product is intended for use with UL

Listed products and must be installed by a

qualiﬁ ed professional installer.

Model: CMJ455

Installation & Assembly -

Lightweight Suspended Ceiling

Plate for Projector Mounts

Max. Load Capacity : 50 lb (22.7 kg)

WARNING

• Weight of TV or screen shall not exceed maximum load capacity.

Description Qty. Part #

ceiling tray

1 128-2198

filler tray

1 128-2207

1/4"-20 x 3/8" screws

4 520-2015

1/4"-20 nuts

4 530-9302

allen wrench

1 560-9706

turnbuckle

4 560-9620

20' (6.1m) tie wire (not shown)

1 600-2008

eye bolt

5 580-0006

concrete anchor

5 580-0005

flush mount tube

1 1446-014

M5 x 10 mm penta pin screw

505-9010

M5 x 1" penta pin drive

1 520-9249

Parts List

USC

Summary of content (5 pages)

PAGE 1
Installation & Assembly - UL C © US Lightweight Suspended Ceiling Plate for Projector Mounts Model: CMJ455 This Suspended Ceiling Plate is intended for use only to support Projector Mounts or other products as speciﬁed by Peerless. This product is intended for use with UL Listed products and must be installed by a qualiﬁed professional installer. Max. Load Capacity : 50 lb (22.7 kg) WARNING • Weight of TV or screen shall not exceed maximum load capacity.
PAGE 2
IMPORTANT PRE-ASSEMBLY INFORMATION: Ceiling Trays (A), and (A1) are designed to ﬁt within a 24" (610 mm) x 24" (610 mm) section of a conventional suspended ceiling system. Ceiling runners (see DETAIL 1, page 4) should have a "T" cross section and a minimum height of 1.5" (38 mm). In cases where 24" (610 mm) x 48" (1219 mm) ceiling tiles are used, cut one tile in half and add another 24" (610 mm) ceiling runner in order to make a 24" (610 mm) x 24" (610 mm) section.
PAGE 3
Place Ceiling Tray (A) into 24" (610 mm) x 24" (610 mm) opening in ceiling (in place of a ceiling tile) with retaining collar to center, right, or left. Place ﬁller tray (A1) into gap. Attach ceiling tray (A) to ﬁller tray (A1) using four bolts (B) and four nuts (C). Hook turnbuckles (F) into ceiling tray (A). Hook one turnbuckle through ﬁller tray (A1) and ceiling tray (A) where indicated by black rectangles in illustration below.
PAGE 4
Cut tie wire (G) into four pieces of equal length. Insert wires through the ends of the turnbuckles. Twist each wire around itself at least six times as tightly as possible. Drill holes for four ceiling anchors (see “Various Anchoring Methods”). Position the holes so when the tie wires are attached and taut the optimal angle is 15° (see ﬁgure 5.1 for reference). Unit may be mounted at an angle up to 45° if necessary. Pull tie wires tight and attach to ends of ceiling anchors (or truss).
PAGE 5
LIMITED FIVE-YEAR WARRANTY Peerless Industries, Inc. establishes a warranty period of ﬁve years for products manufactured or supplied by Peerless. This period commences from the date of sale of the product to the original consumer, but will in no case last for more than six years after the date of the product’s manufacture.