Installation and Assembly: Wallmount for CPA100 and Whiteboard Model: A100IWBMOUNT Maximum Load Capacity for Screen: 53 lb (24 kg) Maximum Load Capacity for Projector : 13.5 lb (6 kg) 1 of 16 ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08 W. NorthWeb Ave. Site • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) • www.peerlessmounts.com Visit3215 the Peerless at www.peerlessmounts.com For customer care call865-2941 1-800-865-2112 or 708-865-8870.
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112.
Before you begin, make sure all parts shown are included with your product. A B Parts List A B C D E F G H I J K L M N O P Q R S T U V W X Y Z Description wall mount assembly projector tube projector arm adapter plate hook bracket vertical handle horizontal handle projector adapter plate slide plate projector mount #10-32 x 0.375" phillips screw M6 x 12 mm serrated washer head socket pin screw 0.25"ID spacer 1/4-20 x 1.0" hex head screw #10-32 x 3/8" serrated washer head socket pin screw 0.
Parts List Continued U V W X Y Z 1 Make sure that wall mount assembly (A) is level, use it as a template to mark the top two mouting holes. Alternatively, the top two screws can be fastened 16" apart as detailed in step 2 while making sure that they are level. In order to set the desired height of bottom of screen in the lowest position, refer to dimension X from the chart below.
Installation to Wood Stud Wall WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). • Make sure that mounting screws are anchored into the center of the stud.
Installation to Solid Concrete or Cinder Block WARNING • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications.
Installation to Metal Stud Wall (Metal Stud Accessory Kit ACC 615 Required) WARNING • Drywall must be 1/2" or thicker, and metal stud must be 24 gauge or thicker. • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. 2 Drill six 1/2" holes through drywall and metal studs. NOTE: It may be necessary to drill 5/32" pilot holes prior to drilling 1/2" holes.
3 Slide projector tube (B) into top of wall mount assembly (A) and secure with two #10-32 x 0.375" phillips screws (K) as shown below. NOTE: Use correct set of mounting holes for the screen size as shown below. 4 Fasten three #10-32 x 0.375" phillips screws (K) to carriage leaving three threads exposed. Attach retainer bushing (Y) and flanged bushing (X) to wall mount assembly (A) using two #10-32 x 0.375" phillips screws (K). 63" SCREEN B NOTE: Twist tube into wall mount assembly (A).
5 Fasten two #10-32 x 0.375" phillips screws (K) into adapter plate (D) leaving three threads exposed as shown in detail 1. Hook each vertical handle (F) onto #10-32 x 0.375" phillips screw (K) as shown in fig 5.1. NOTE: Use top slot for 77" screen or second slot from top for 63" screen. Fasten #10-32 x 0.375" phillips screws (K) through lower slot of vertical handle (F) that lines up with the lower hole in adapter plate (D). Hole location for 77" screen is shown in fig. 5.2.
7 Insert hook brackets into screen as shown in detail 2 and fig. 7.1. Secure each hook bracket (E) with M6 x 12 mm serrated washer head socket pin screw (L) as shown in fig. 7.2 and detail 3. SCREEN BRACKET SCREEN 63" SCREEN E 77" SCREEN DETAIL 2 fig. 7.1 SCREEN E L DETAIL 3 fig. 7.2 10 of 16 Visit the Peerless Web Site at www.peerlessmounts.com ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08 For customer care call 1-800-865-2112 or 708-865-8870.
8 Hook brackets (E) into adapter plate (D) as shown in fig. 8.1 and detail 4. The hooks will go over the flange on the top and the bottom of hook bracket (E) into the slots as shown in detail 4 and detail 6. Fasten #10-32 x 1-3/8" socket pin screws (T) on each hook bracket (E), using security allen wrench (V) and tighten to wall plate as shown in detail 5. To remove screen from mount, loosen safety/security screws and lift screen off of mount.
10 Arrow on projector mount assembly (J) indicates front of mount. The arrow of projector mount assembly (J) should face towards the round tube on projector arm (C). Fasten projector mount assembly (J) to projector arm (C) using two 1/4-20 x 1.0" hex head screws (N), four 0.25" ID nylon washers (P) and slide plate (I) as shown in fig. 10.2 and 10.3. Do not tighten 1/4-20 x 1.0" hex head screws (N) fully to allow for adjustment. Insert rectangle plug (S) into projector arm (C) as shown in fig. 10.2.
11 Place projector arm (C) onto projector tube (B) as shown in fig. 11.1. Align projector arm (C) so that the holes in projector tube (B) are in the middle of projector arm (C) slot. NOTE: This can be adjusted during final projector alignment if needed. Fasten projector arm (C) to projector tube (B) using two #10-32 x 3/8" serrated washer head socket pin screws (O) as shown in fig. 11.2 and detail 6. C B fig. 11.1 C B O DETAIL 6 fig. 11.2 13 of 16 Visit the Peerless Web Site at www.peerlessmounts.
Attaching Adapter Plate to Projector 12 adapter plate (H). Attach adapter plate (H) to Align shoulder on connection block opposite notch in CONNECTION BLOCK connection block from projector mount assembly (J) using two #10-32 x 3/8" serrated washer head socket pin screws (O). SHOULDER H NOTCH INDICATES FRONT OF PROJECTOR O 13 four M6 x 12 mm serrated washer head Attach adapter plate (H) to projector using socket pin screws (L) and 0.25" spacers (M).
Attaching Adapter Plate to Projector Mount WARNING • Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the projector. 14 Slide connection block with projector into projector mount assembly (J) as shown. Tighten captive screw to secure projector to projector mount assembly (J). ARROW INDICATES FRONT OF MOUNT J CONNECTION BLOCK FRONT OF MOUNT CAPTIVE SCREW 15 assembly (J) and into connection block as shown.
Projector Alignment 16 To adjust yaw (swivel): Loosen screw on projector mount assembly (J) indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw. To adjust pitch (forward and backward tilt): Turn knob on back of mount as shown below. Pull knob out and turn by hand for easy adjustment or insert #2 phillips screwdriver in end of knob and turn. To adjust roll (side to side tilt): Turn knob on side of mount as shown below.
