Projector Accessories User Manual

ManualsBrandsPeerless Industries ManualsProjector AccessoriesPeerless PRG Precision Gear Projector Mount PRG-1W

ISSUED: 08-15-07 SHEET #: 055-9491-7 06-11-11

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800)359-6500 • www.peerlessmounts.com

Maximum UL Load Capacity:

50 lb (22.7 kg)

Installation and Assembly Manual:

PRG Precision Gear Projector Mount

USC

This product is intended for use with UL

Listed products and must be installed by a

qualiﬁ ed professional installer.

Models: PRG-1, PRG-1S, PRG-1W

Features:

• ImageLock

alignment prevents picture sag or drift

• Exclusive aluminum track quick release

Summary of content (13 pages)

PAGE 1
Installation and Assembly Manual: PRG Precision Gear Projector Mount Models: PRG-1, PRG-1S, PRG-1W C Features: • ImageLockTM alignment prevents picture sag or drift • Exclusive aluminum track quick release UL © US This product is intended for use with UL Listed products and must be installed by a qualiﬁed professional installer. Maximum UL Load Capacity: 50 lb (22.7 kg) 2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800)359-6500 • www.peerlessmounts.
PAGE 2
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112.
PAGE 3
Before you start check the parts list to insure all of the parts shown are included.
PAGE 4
Installation to Extension Column / Ceiling Plate 1 NOTE: Refer to accompanying instructions with ceiling plates (sold separately) for installing these models to ceiling. Screw projector mount assembly (A) onto extension column as shown in ﬁgure 1.1. Tighten swivel stop screw against extension column, ﬂush mount tube or reducer using 4mm security allen wrench (B) as shown in ﬁgure 1.2.
PAGE 5
Installation To Wood Joist Ceilings WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that projector mount assembly is ﬁrmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). • Make sure that mounting screws are anchored into the center of the stud.
PAGE 6
Installation to Concrete Ceilings WARNING • Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. 1 Place projector mount assembly (A) on ceiling as a template and mark the center of the two mounting holes. Drill two 5/16" (8mm) dia. holes to a minimum depth of 2-1/2" (64mm).
PAGE 7
Installation to Threaded Rod (Not evaluated by UL - Professional installation only) 4 Thread two 1/4-20 hex thin nylon-insert locknuts (not included) on two 1/4-20 threaded rods (not included) to the desired height of projector mount assembly. Attach projector mount assembly (A) to the two 1/4-20 threaded rods using two 1/4-20 hex thin nylon-insert locknuts as shown in ﬁgure 4.1 or ﬁgure 4.2.
PAGE 8
Attaching Adapter Plate to Projector CAUTION I • It is the responsibility of the installer to ensure that the projector is properly ventilated. 5 SHOULDER NOTCH INDICATES FRONT OF PROJECTOR Installing Dedicated PAP Series Adapter Plate (sold separately) DEDICATED ADAPTER PLATE (SOLD SEPARATELY) NOTE: The projector dedicated adapter plate you are installing may differ in appearance from the sample illustrated in ﬁgure 5.1. Align shoulder of connection block (I) opposite notch of adapter plate.
PAGE 9
Attaching Adapter Plate to Projector Mount WARNING • Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the projector. 6 Slide connection block (I) with projector into projector mount assembly (A) as shown. Tighten captive screw to secure projector to projector mount assembly (A).
PAGE 10
Cable Management 8 ﬁg. 8.1 To make an opening to route cables through projector mount assembly, adjust projector mount assembly to full upward tilt position by turning knob for tilt adjustment as shown in ﬁgure 8.2. Left or right roll position can be adjusted if more space is required. NOTE: Be certain tamper resistant screws are not engaged before making adjustments (see step 9). Route cables through top of extension column as shown in ﬁgure 8.1 and ﬁgure 8.2.
PAGE 11
Projector Alignment To adjust yaw (swivel) for threaded rod mounting applications: Loosen locknuts on threaded rods (step 5), until projector mount can be rotated. Rotate mount to desired position and retighten locknuts. 9 To adjust yaw (swivel) for extension column applications: Loosen screw on projector mount assembly (A) indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw.
PAGE 12
PRG Series Projector Mount Accessories Ceiling Plates Escutcheon Ring Unistrut® Adapter Truss Ceiling Adapter MODEL: ACC 557* MAX LOAD: 250 lbs. (113.4 kg.) COLOR: Black MODEL: ACC 640 MODEL: ACC 550 MAX LOAD: 250 lbs. (113.4 kg.
PAGE 13
PRG Series Projector Mount Accessories Cord Management • Includes, four, 2' sections • Designed to externally route cords along the outside of an 1/2" extension column • Sections can be stacked to create longer lengths or cut to desired length Cord Wrap MODELS: ACC 852(W)(S)* COLOR: Black, White, or Silver Extension Columns Fixed Length 1 1/2" Extension Columns Adjustable Length 1 1/2" Extension Columns COLOR: Black COLOR: Black MODEL EXT 006 EXT 018 EXT 101 EXT 102 EXT 103 EXT 104 EXT 105 EXT 106 EXT