Installation and Assembly: PRS Projector Mount with Universal Adapter Plate Models: PRS-UNV, PRS-UNV-S, PRS-UNV-W R This product is intended for use with UL Listed products and must be installed by a qualified professional installer. Maximum UL Load Capacity: 25 lb (11.34 kg) 2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800)359-6500 • www.peerlessmounts.
Note: Read entire instruction sheet before you start installation and assembly. WARNING • • • • • • • • • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor.
Before you start check the parts list to insure all of the parts shown are included. Parts List A B C D E F G H I J K L M Description projector mount assembly adapter plate #14 x 2.
Installation to Extension Column / Ceiling Plate 1 NOTE: Refer to accompanying instructions with ceiling plates (sold separately) for installing these models to ceiling. Screw projector mount assembly (A) onto extension column as shown in figure 1.1. Tighten swivel stop screw against extension column, flush mount tube or reducer using 4 mm security t-wrench (L) as shown in figure 1.2.
Installation To Wood Joist Ceilings WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that projector mount assembly is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). • Make sure that mounting screws are anchored into the center of the stud.
Installation to Concrete Ceilings WARNING • Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. 3 Place projector mount assembly (A) on ceiling as a template and mark the center of the two mounting holes. Drill two 5/16" (8 mm) dia. holes to a minimum depth of 2.5" (64 mm).
Installation to Threaded Rod (Not evaluated by UL - Professional installation only) 4 Thread two 3/8-16 hex thin nylon-insert locknuts (not included) on two 3/8-16 threaded rods (not included) to the desired height of projector mount assembly. Attach projector mount assembly (A) to the two 3/8-16 threaded rods using two 3/8-16 hex thin nylon-insert locknuts as shown in figure 4.1 or figure 4.2.
Attaching Adapter Plate to Projector Note: The projector you are installing may differ in appearance from the sample illustrated below. 5 Place projector upside down. Locate adapter plate (B) with notch facing forward as close to projector center of gravity as possible without covering any mounting holes. Loosen channels with 4 mm security t-wrench (L), and if there are only three mounting holes remove fourth channel.
Attaching Adapter Plate to Projector (continued) WARNING • Always use an assistant or mechanical lifting equipment to safely lift and position the projector. 7 Slide connection block with projector into projector mount assembly (A) as shown. Push in and tighten captive screw to secure projector to projector mount assembly (A).
Projector Alignment 9 To adjust yaw (swivel) for threaded rod mounting applications: Loosen locknuts on threaded rods (refer to step four), until projector mount can be rotated. Rotate mount to desired position and retighten screws or locknuts. To adjust yaw (swivel) for extension column applications: Loosen screw on projector mount assembly (A) indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw.
PRS Series Projector Mount Accessories Ceiling Plates Escutcheon Ring Unistrut® Adapter Truss Ceiling Adapter MODEL: ACC 557* MAX LOAD: 250 lbs. (113.4 kg.) COLOR: Black MODEL: ACC 550 MAX LOAD: 250 lbs. (113.4 kg.
PRS Series Projector Mount Accessories Cord Management • Includes, four, 2' sections • Designed to externally route cords along the outside of an 1/2" extension column • Sections can be stacked to create longer lengths or cut to desired length Cord Wrap MODELS: ACC 852(W)(S)* COLOR: Black, White, or Silver Extension Columns Fixed Length 1 1/2" Extension Columns Adjustable Length 1 1/2" Extension Columns COLOR: Black COLOR: Black MODEL EXT 006 EXT 018 EXT 101 EXT 102 EXT 103 EXT 104 EXT 105 EXT 106 EXT