Installation and Assembly: 32" - 50" Flat Panel TV Stand Models: SS550P, SS550P-S R This product is UL Listed. It must be installed by a qualified professional installer. Max Load Capacity: 150 lb (68 kg) screen 50 lb (22.7 kg) per shelf 3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.
Note: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112.
A B Before you begin, make sure all parts shown are included with your product. Parts List A B C D E F G H I J K L M N O P Q R S T U G Description screen mount bracket hook plate shelf support shelf clamp bracket base universal plate adapter bracket upright glass shelf top cover button bumper 1/4-20 x 12mm decorative screw 1/4-20 x 20mm decorative screw 1/4-20mm nut 5/16" flat washer 3/8-16 x 2.
Phillips Adapter Bracket Fasteners M4 x 12 mm (6) 504-9013 M4 x 25 mm (4) 504-1015 M5 x 12 mm (4) 520-1027 M6 x 30 mm (4) 510-9109 M6 x 12 mm (4) 520-1128 M6 x 25 mm (4) 520-1208 M8 x 16 mm (6) 520-9257 M6 x 20 mm (4) 520-9402 M8 x 25 mm (4) 520-1031 multi-washer (6) 580-1036 M8 x 40 mm (4) 520-1136 I.D. .22" (5.6 mm) (4) 540-1057 1 M5 x 25 mm (4) 520-9543 I.D. .34" (8.7 mm) (4) 540-1059 Cut adhesive felt (S) into four pieces as shown in figure 1.1 below and affix to bottom of base (E).
2 Loosely attach four 1/4-20 x 12 mm screws (L), washers (O), and 1/4-20 nuts (N) to shelf support (C). Slide shelf support (C) onto upright (H) so that 1/4-20 nuts (N) slide into slots of upright (H) as shown in figure 3 and detail 1. Slide shelf support to desired position, level, then tighten 1/4-20 x 12 mm screws (L) using 4 mm allen wrench (R). 3 3-1 NOTE: MAXIMUM OF TWO SHELVES Max height of top shelf is 34" from base. Max height of second shelf is 28" from base.
Loosely attach six 1/4-20 x 12 mm screws (L), washers (O), and 1/4-20 nuts (N) to screen mount bracket (A). Slide screen mount bracket (A) onto upright (H) so that 1/4-20 nuts (N) slide into slots of upright (H) as shown in figure 7 and detail 2. Slide screen mount bracket to desired position, level, then tighten 1/4-20 x 12 mm screws (L) using 4 mm allen wrench (R). 7 N A N L SLOT H DETAIL 2 L O H A fig. 7 8 9 Snap top cover (J) onto upright (H).
Attaching Screen Using Universal Plate with Adapter Brackets For attaching screens with VESA 100 hole pattern, skip to page 10. 10 Attach universal plate (F) to hook plate (B) using four M10 x 15 mm socket screws (T). Tighten screws using 6 mm allen wrench (U). 11 Attach hook plate (B) to screen mount bracket (A). B F B T 12 A Insert two 1/4-20 x 12 mm screws (L) into holes indicated below for desired screen orientation. Tighten all screws using 4 mm allen wrench (R).
Installing Adapter Brackets WARNING • Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque. • If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.
For Flat Back Screen 13-1 Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/2 for a full screen compatibility chart for this mount. Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten.
Mounting and Removing Flat Panel Screen WARNING • Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television. 14 Hook adapter brackets (G) onto universal plate (F), then slowly swing screen in as shown. Turn screws clockwise at least six times to prevent screen from being removed as shown in detail 4. Note: Tighten using 4 mm allen wrench (R). Screen can be adjusted horizontally if desired.
Attaching Screen with VESA 100 Mounting Pattern WARNING • If screws don't get three complete turns in the screen inserts or if screws bottom out and hook plate is still not tightly secured, damage may occur to screen or product may fail. 10 Choose hole pattern as shown in figure 10. Attach hook plate (B) to back of screen using four M4 x 12 mm screws. Tighten screws using a phillips screwdriver. 11 Attach hook plate (B) to screen mount bracket (A).
