Manual

2
5
⁄16”
7
1
⁄8”
SCEP option
DAY
5
DAY
10
5
10
DAY
5
DAY
10
5
10
Catalog Number
Sample Catalog Number: 7CRM1QS 2 54T5HO WHR 36FT R12 277 GEB10 SCT LP835 F1/21 C210
___________ ___________ ___________ ___________ ___________ ___________ ___________
Emergency Type
1
Switching Lamp Color Mounting Type / Overall Suspension
3
Finish Options
(Blank) None
EC
2
Emergency
circuit
EL Emergency
battery pack
EN
2
Emergency
battery pack
w/night light
circuit
SCT Single circuit
DCT
2
Dual circuit
L/LP No lamps
LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI
F1/ T-bar ceiling (universal
mounting bracket)
F1A/ T-bar ceiling (UMB with
integrated J-box)
F2/ Hard ceiling (horizontal
J-box)
12 12”
15 15”
18 18”
21 21”
24 24”
XX XX”
Overall suspension is
measured from ceiling to
bottom of luminaire
C210 White white
(fine-textured
low gloss)
ACG Adjustable cable grippers
CP Chicago plenum (available with F1A only)
DU
4
Dust cover
ELH Emergency through wiring w/separate feed
ELS
2
Emergency through wiring w/single feed, shared neutral
ELS2
2
Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
MCS Matching feed canopy at support
OJB Oset junction box
SCEP Sculptured end cap
___________ ___________ ___________ ___________ ___________ ___________ ___________
Luminaire # of Lamps in
Cross Section
Lamp Type Reflector Luminaire Row
Length
Maximum
Section Length
Voltage Ballast Type # of Emergency
Modules
7CRM1QS
7CRM1QST
1
2
3
28T5 28W T5
54T5HO 54W T5HO
WHR White
reflector
SPR Specular
reflector
X FT
(4’ increments)
R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)
120
277
GEB10 <10% THD Electronic
(32 T8, 28T5, 54T5HO)
GEB10/347V 347V Generic non-dim. Only
available with 10-day QuickShip
ADEZ Advance Mark 10 dim (54T5HO)
OSDIM Osram 0-10V dim (54T5HO)
ADZT Advance Mark 7 0-10V dim
(54T5HO). Only available
with 10-day QuickShip
(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections
Specifications
CONSTRUCTION — Nominal 7” x 2” crescent housing is formed from one-piece cold-rolled steel.
Flat end plate standard. Sculptured die-cast aluminum end cap is optional.
REFLECTORS — Die-formed highly reflective white or specular reflector.
FINISH — Fine textured white polyester powder paint.
LUMINAIRE LENGTH — 4’, 8’, and 12’ lengths in a single section for exact suspension spacing of
4’, 8’, and 12’. For total luminaire length, add
1
⁄16” for each flat end plate or 3” for each sculptured end
cap. Using internal joiners, 4’, 8’, and 12’ sections can be joined to form longer length luminaires.
DISTRIBUTION — 0% downlight. See non-QuickShip spec sheet for photometrics.
7CRM1QS
Dimensions / Lamping
(1,2,3) T5, T5HO
Cerra
®
7
INDIRECT
Notes: 1 EL and EC are installed in last 4’ of luminaire sections. Separate feed required unless ELS or ELS2 is specified
2 Not available with dimming 3 Maximum of 240” 4 Not available with 3 lamp 54T5HO
2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com
© 2013 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Cerra” are registered trademarks of Acuity Brands Lighting. Products in this document may be covered by one or more U.S. Patents and Patents Pending.
Specifications subject to change without notice. 1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx