Manual

LAMPING OPTIONS
SPECIFICATIONS
2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com
CATALOG NUMBER
SPECIFICATIONS
__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________
Specify by Low (LO) or High (HI) LO HI
Nominal Delivered Lumens* 1800 2400
Watts* 17 23
Lumen Packages:
* nominal per 4’
1
© 2013 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Peerless Bruno” are registered trademarks of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
5-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx
Indirect/Direct
BRW9L Bruno Wall LED Softshine
Type: ________________________
Project: ______________________
Wall Mount BRW9L
Bruno Wall LED
Softshine
Indirect/Direct
BRW9L
Construction
Nominal 8
1
⁄4” x 1
3
⁄4” rectangular housing is formed
from cold-rolled steel. Die-cast end caps are
mechanically attached with no exposed fasteners.
Source
Two LED lumen packages and three available color
temperature options (3000K, 3500K and 4000K).
Optics
Softshine®-engineered optical system consists
of high performance lens, diusers and metal
reflectors.
Finish
Finish for housing and end caps is white,
black or painted aluminum. Consult factory
for custom colors.
Controls
Optional nLight-embedded controls allow for
constant lumen management (LM).
Electrical
LED light engine consists of modular LED boards
and 0-10V dimming driver rated for 50,000 hours
(L
80
) at 25° C ambient temperature. Driver input
wattage is 17W for 1800 delivered-lumen package,
23W for 2400 delivered-lumen package, per 4’
section. Specify 120V or 277V. Pre-wired with
16AWG fixture wire. For special circuiting or wire
gauge, consult factory. Plug-in electrical connectors
included.
Environment
Damp location label option. Ambient operating
temperature between 0° C and 25° C.
Luminaire Length
4’ and 8’ lengths in a single section for exact
suspension spacing of 4’ and 8’. For total luminaire
length, add
5
⁄8” for each flat end cap and 4” for each
sculptured end cap.. Using internal joiners, 4’ and 8’
sections can be joined to form longer rows.
Validation
CSA/CUS listed. Individual sections are FCC part
15 certified. LM-79 tested. Lighting Facts partner.
Warranty
Five-year warranty coverage includes luminaire
construction, LED light engine, driver and optional
nLight control device. Terms and conditions apply.
Packaging
100% post-consumer recycled cardboard box and
inserts. Biodegradable, protective luminaire bag.
Recycled kraft paper tape.
__________ __________ _________ __________ __________ __________ __________ __________
Luminaire
BRW9L
Light Output
LO 1800 nominal
delivered-lumens
HI
2400 nominal
delivered-lumens
Shielding
SSH Softshine®
lens
Luminaire
Row Length
X FT
(4’ increments)
Maximum
Section Length
R4 4’ section(s)
R8 8’ section(s)
Voltage
120
277
Driver Type
EZB eldoLED dims to black
# of Emergency
Modules
(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections
Emergency
Type
1
(Blank) None
EC Emergency
circuit
Switching
SCT Single
circuit
______________ ______________ _________________________________
LED Color Temperature
LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP840 4000K 80+ CRI
Finish
C210 White white (fine textured)
C110 Painted aluminun
C202 Black
C099 Custom finish
Options
CFG Configuration, consult factory for drawings
DL Damp location label
DU Dust cover
ELH
2
Emergency through wiring w/separate feed
GLR Fusing (fast blow)
GMF Fusing (slow blow)
LM 80% lumen management without networking
SCEP Sculptured end caps
Notes:
1 Emergency type is installed in last 4’ of luminaire
sections. Separate feed required
2 No dimming control on emergency feed
1
3
⁄4”
8
1
⁄4”