Manual

LAMPING OPTIONS
SPECIFICATIONS
CATALOG NUMBER
SPECIFICATIONS
2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com
__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________
Type: ________________________
Project: ______________________
1
© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Envision” are registered trademarks of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx
Indirect T8
ENW1 Envision Wall
Wall Mount ENW1
Examples: ENW1 010005 T8 36FT R12 120 GEB10 2SE EL SCT LP835 C041 — ENW1 020006 T8 24FT R8 277 GEB10 DCT LP841 C041
Envision Wall
Indirect T8
ENW1 - 1 ENW1 - 2
3”
9”
3”
9”
Construction
Housing is extruded aluminum forming a 9” x 3”
curved profile. Die-cast end plate attaches with no
exposed fasteners.
Reflectors
Die-formed, pre-finished steel and hammertone
specular aluminum reflector.
Finish
Satin anodized or white paint standard. Custom
colors available, consult factory.
Electrical
Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.
Luminaire Length
4’, 8’, and 12’ lengths in a single section. For total
luminaire length add
1
⁄2” for each end cap. Using
internal joiners, 4’, 8’, and 12’ sections can be joined
to form longer-length luminaires. Individual 2’ and 3’
units also available, consult factory.
________ ________ ________ ________ ________ ________ ________________________ ______________ ______________
Luminaire
ENW1
# of Lamps
in Cross
Section
010005 1
020006 2
Lamp Type
32 32W T8
Nominal
Row
Length
X FT
(4’ increments)
Maximum
Section
Length
R2 2’ section(s)
R3 3’ section(s)
R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)
Voltage
120
277
347
Ballast Type
GEB10 <10% THD Electronic
ADEZ
1
Advance Mark 10 dim
DMHL3D
1
Lutron Hi-Lume dim
ADZT
1
Advance Mark 7 0-10V dim
Reference Ballast Wizard on website
or consult factory for other options.
# of Emergency
Modules
(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections
Emergency Type
2
(Blank) None
EC Emergency circuit
EL
1
Emergency battery
pack
EN
1
Emergency battery
pack w/night light
circuit
________ ________________ ______________ _________________________________
Switching
SCT Single circuit
DCT Dual circuit
Lamp Color
L/LP No lamp
L/LPE No lamp. Wired for energy
saving lamps.
LP830
3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI
Reference Lamp Chart on website or
consult factory for other options.
Finish
C041 White white (low gloss)
C100 Satin anodized finish
C099 Custom finish
Options
CFG Configuration
DL Damp location label
DU Dust cover
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
NYC New York City code
Notes:
1 Not available in 347V
2 Emergency type is installed in last 4’ of luminaire sections.
Separate feed required unless ELS or ELS2 is specified