DS-C555-4X2 46" - 55" (117 - 140cm) MAX 800 lb (363 kg) ENG 1 2014-06-20 #:009-9085-2.
This page intentionally left blank. 2 2014-06-20 #:009-9085-2.
WARNING Do not begin to install product until you have read and understood the instructions and warnings contained in this user guide. Always use an assistant or mechanical lifting equipment to safely lift and position equipment. This product must be installed onto flat, hard, level surface to prevent tipping. The cart or stand is not affixed or secured to the floor, and may therefore tip over and/or fall if screen and/or stand is shaken or hit. Displays must be removed before moving cart.
Parts (Before beginning, make sure you have all parts shown below).
L (1 ) computer cover N (4 ) M (1 ) computer shelf dual cross support O (6 ) locking tab P (6 ) cord bracket Q (2 ) bracket, 4x2 configuration R (180) S (108) M8 x 16mm M8 square nut T (36) cover clip X (1 ) 5mm allen wrench U (18) Y (32) nylon shoulder washer W (1 ) V (6) M5 x 10mm 1/4" power bit M5 x 12mm Z (32) M6 x 12mm 5 AA (1) 4mm allen wrench 2014-06-20 #:009-9085-2.
1 B Repeat for each caster assembly. X A (5mm) R (4) Do not fully tighten hardware S (2) R (2) SIDE VIEW 6 2014-06-20 #:009-9085-2.
2 Repeat for each base leg assembly. S (2) X (5mm) S (2) D R (4) F S (2) S (2) R (4) 7 F 2014-06-20 #:009-9085-2.
3 Repeat for each base leg assembly. TIGHTEN CONNECTING HARDWARE 4 Repeat for each base support (x12). R (4) Do not fully tighten hardware S (4) G SIDE VIEW 8 2014-06-20 #:009-9085-2.
5 TIGHTEN CONNECTING HARDWARE Repeat for each side (x2). H 6 TIGHTEN CONNECTING HARDWARE Assemble middle support bracket. H 9 2014-06-20 #:009-9085-2.
7 TIGHTEN CONNECTING HARDWARE E LOCK WHEELS E 8 Repeat for each vertical support bracket (x4). 1/8" (3mm) S (4) 1/8" (3mm) R (6) K 10 2014-06-20 #:009-9085-2.
a 9 Use metric formula below and diagram to right to determine hole pattern required for center vertical support bracket. Repeat (x2). b All dimensions are metric. BACK OF DISPLAY Use the outside mounting holes when… a x 4 > 4368mm and a x 3 + b < 4318mm S (8) Q R (12) Use the inside mounting holes when… a x 4 > 4098mm and a x 3 + b < 4064mm S (8) Q 1/8" (3mm) SIDE R (12) BACK 11 2014-06-20 #:009-9085-2.
10 DIS PL AY H EIG HT 11 TIGHTEN CONNECTING HARDWARE N N 12 2014-06-20 #:009-9085-2.
12 TIGHTEN CONNECTING HARDWARE N N 13 R (2) J S (2) 13 2014-06-20 #:009-9085-2.
O P V TIGHTEN CONNECTING HARDWARE O P OPTIONAL: Unlock wheels to move cart to desired location; Lock wheels before hanging screens. LOCK WHEELS V TOP VIEW 14 2014-06-20 #:009-9085-2.
Center adaptor brackets vertically on back of screen. X .98" (25mm) 7.87" (200mm) 3.94" (100mm) 2.50" (63mm) 15.75" (400mm) X 2.50" (63mm) 0.91" (23mm) AA (4mm) Y Z OR 15 R x3 2014-06-20 #:009-9085-2.
-1 Must hang displays to bottom row first; Secure pin in "locked" position. "LOCKED" POSITION 16-2 Must hang displays on top row last; Secure pin in "locked" position. "LOCKED" POSITION 16 2014-06-20 #:009-9085-2.
16-3 OPTIONAL: Insert M5 x 10mm type-F socket pin screws to lock latches. AA U 17 2014-06-20 #:009-9085-2.
Display Adjustment IN OUT SIDE SIDE TILT BACKWARD SIDE TILT RIGHT TILT LEFT TOP SIDE UP TILT FORWARD TOP DOWN ROTATE LEFT 18 ROTATE RIGHT 2014-06-20 #:009-9085-2.
17 M 18 1/8" (3mm) M L U (2) TIGHTEN CONNECTING HARDWARE M 19 2014-06-20 #:009-9085-2.
19 T (4) C 20 2014-06-20 #:009-9085-2.
20 Route cables through cord brackets. P P 21 2014-06-20 #:009-9085-2.
21 Display Removal Pull down on bracket cords and hold. Swing screen away from cart and lift to remove. 22 Remove displays from top row first. "UNLOCKED" POSITION 22 2014-06-20 #:009-9085-2.
Repeat step 21 to remove displays from bottom row last. "UNLOCKED" POSITION 23 2014-06-20 #:009-9085-2.
LIMITED FIVE-YEAR WARRANTY Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal use, for a period of five years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product's manufacture). At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.