manual

ManualsBrandsPeerless ManualsTVs & monitorsLCT-202

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 07-31-09 SHEET #: 090-9183-2 10-29-09

Max Load Capacity: 25 lb (11.3 kg) per arm

Installation and Assembly:

Dual-Screen Desktop Mount for 10" to 20" LCD Monitors

Models: LCT-202

Summary of content (7 pages)

PAGE 1
Installation and Assembly: Dual-Screen Desktop Mount for 10" to 20" LCD Monitors Models: LCT-202 Max Load Capacity: 25 lb (11.3 kg) per arm 3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.
PAGE 2
Note: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor.
PAGE 3
Before you begin, make sure all parts shown are included with your product. Parts list A B C D e F G H I J K L M N o P Q R Description Dual arm column VESA plate Column cover* Base M6 flat washer M6 lock washer M6 hex head screw adhesive cable anchors #8 phillips self-tapping screw* M10 flat washer* M10 split lock washer* M10 wingnut* rubber bumpers M4 flat washer M4 lock washer M4 pan phillips head screw cable ties 5 mm allen wrench Qty.
PAGE 4
Cable Management 1 Remove #8 self-tapping screw (I) using a phillips screw driver to unattach column cover (C) from dual arm column (A). Insert cables into cavity of the dual arm column (A) as shown in figure 1.1 and reattach column cover (C) to back of dual arm column (A) using #8 self-tapping screw (I). NOTE: Be sure connectors are in their proper orientation. Allow enough cable slack to connect to display.
PAGE 5
Attaching VESA Plates to Display WARNING • Tighten screws so VESA plates are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque. • If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.
PAGE 6
Attaching Dual Arm Assembly to Base WARNING • Be sure display is unplugged from any electrical outlet while assembling dual stand. • Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
PAGE 7
WARNING • Use two displays with this mount. Product may fail and damage property if not installed correctly. 5 Apply rubber bumpers (M) to bottom of base as shown in figure 5.1. Carefully lift the full assembly to its upright position as shown in figure 5.2. NOTE: Be sure assembly rests on a flat, level surface to prevent the displays from tipping. M fig 5.1 fig 5.2 NOTE: Leave a small gap between the displays to allow for horizontal pivot adjustment as shown below.