Installation Guide

ManualsBrandsPeerless ManualsShower FaucetsP188710

SINGLE HANDLE WASHERLESS PRESSURE

BALANCED TUB & SHOWER VALVES

MODELS P188710 & P188720

VÁLVULAS DE REGADRAY BAÑERA DE PRESIÓN

BALANCEADA SIN ARANDELAS

MODELOS P188710 & P188720

ROBINET DE BAIGNOIRE/DOUCHE MONOCOMMANDE

À ÉQUILIBRAGE DE PRESSION

MODÈLES P188710 & P188720

Estimated Time For Assembly

The estimated time to install this tub and shower valve is 85 minutes.

These estimates do not include removing the old shower system.

Tiempo Estimado para Instalar

El tiempo estimado para instalar esta válvula de bañera y regadera es

85 minutos. Estos estimados no incluyen el tiempo que tomaría quitar el

sistema viejo de regadera.

Durée d’installation estimée

Le temps requis pour l’installation du robinet de baignoire-douche est

estimé à 85 minutes. L’estimation n’inclut pas la dépose de la vieille

robinetterie de douche.

You may need

Usted puede necesitar

Articles dont vous pouvez avoir besoin:

Wrench(es):

(NOT PROVIDED)

For faucet removal/installation.

Llave(s):

(NO PROPORCIONADAS)

Para quitar/instalación de lavamanos.

Clé(s):

(NON FOURNIS)

pour pose et dépose de robinet

Record Your Model Number Here For Future Reference

Anote Aquí Número del Modelo Comprado Para Referencia Futura

Inscrivez le numéro de modèle ici pour pouvoir le retrouver.

Instruction Manual Printed in China

Manual de Instrucciones Impreso en China

Manuel d’instructions Imprimé en Chine

1 66821 Rev. A

The Peerless

Installation Helpline

1-800-438-6673

www.peerless-faucet.com

ASSEMBLY PARTS LIST

LISTA DE PIEZAS PARA LA INSTALACIÓN

LISTE DES PIÈCES

Description

Descripción

Description

Quantity

Calidad

Quantité

P188710

P188720

Showerhead

Cabeza de Regadera

Pomme de douche

1 1

Shower Arm & Flange

Brazo de Regadera y Brida

Pomme de douche et collerette

1 1

Trim Sleeve

Manguito

Manchon de Finition

1 1

Valve Body & Cartridge Assembly

Cuerpo de la Válvula y Ensamble del Casquete

Corps de robinet et Cartouche

1 1

Tub Spout (Diverter)

Tubo de Salida para Bañera (Desviador)

Bec de baignoire avec dérivation

NA 1

Lever Handle w/Button & Screw

Palanca con Botone y Tornillo

Manette avec bouton et vis

1 1

Escutcheon

Chapetón

Boîtier

1 1

Escutcheon Screws

Tornillos para chapetón

Vis pour boîtier

2 2

Teflon

tape:

(NOT PROVIDED)

For use on threaded connections.

Cinta Teflon

(NO PROPORCIONADAS)

Para uso con conexiones enroscadas.

Ruban de Téflon

(NON FOURNI)

Pour application sur le filetage des raccords.

Hole Dimensions

(minimum and maximum

hole size in wall for valve

installation)

Las Dimensiones

de los Hoyos

(el tamaño del hoyo mínimo

y máximo en la pared para

la instalación de la válvula)

Dimension du trou

(dimensions minimales et

maximales du trou dans la

paroi pour l’installation de la

soupape)

3 1/2"–5"

(89 mm–127 mm)

CSA B125

ASME A112.18.1

ASSE 1016

4/18/11

Spacer

Separadores

Piéce D’espacement

NA NA

Summary of content (8 pages)

PAGE 1
SINGLE HANDLE WASHERLESS PRESSURE BALANCED TUB & SHOWER VALVES MODELS P188710 & P188720 VÁLVULAS DE REGADRA Y BAÑERA DE PRESIÓN BALANCEADA SIN ARANDELAS MODELOS P188710 & P188720 CSA B125 ASME A112.18.1 ASSE 1016 ROBINET DE BAIGNOIRE/DOUCHE MONOCOMMANDE À ÉQUILIBRAGE DE PRESSION MODÈLES P188710 & P188720 Record Your Model Number Here For Future Reference Anote Aquí Número del Modelo Comprado Para Referencia Futura Inscrivez le numéro de modèle ici pour pouvoir le retrouver.
PAGE 2
1 2 1 2 3 A B Study recommended valve configurations on stringers or framing: (A) Tub/Shower, (B) Shower Only. SHUT OFF WATER SUPPLIES Remove old valve. Install new valve so that the arrows on the bracket (1) point upward. NOTE: Finished wall should line up within prescribed limits on the wall line label (2). For shower only installation, plug bottom valve outlet with pipe plug (3).
PAGE 3
Back to back Installation Instalación de Espalda a Espalda Installation dos à dos Normal Installation (changes not required) Instalación Normal (No serequerá cambios) Installation normale (Non modi ée) Reverse Installation Instalación Invertido Installation Inversée Cold Fría Eau Froides Hot Caliente Eau Chaude FOR BACK TO BACK OR REVERSE INSTALLATIONS ONLY (HOT on RIGHT and COLD on LEFT), follow instructions below.
PAGE 4
5 4 For models with tub spouts, the piping between valve body and tub spout must be a minimum of 1/2" (13 mm) copper pipe or 1/2" (13 mm) iron pipe in a straight drop no less than 8" (203 mm), but no more than 18" (457 mm) long with only one iron pipe or copper 90° elbow to the tub spout nipple. Refer to installation instructions supplied with your tub spout. FLUSH SYSTEM/ CHECK FOR LEAKS. Place handle on valve stem and turn handle to full on mixed position.
PAGE 5
7 Colder Fría Plus froide O-Ring Anillo “O” Joints Toriques Hotter Caliente Plus chaude Rotational Limit Stop Tope para Limitar Rotación Butée Pivotante ADJUSTING THE ROTATIONAL LIMIT STOP: Turn on water so that cold water is as cold as it will get and hot water is as hot as it will get. Place handle back on stem and rotate fully counterclockwise to the hottest position. Place a thermometer in a plastic tumbler and hold in the water stream.
PAGE 6
▲ Specify Finish Especifíque el Acabado Précisez le Fini Valve Body Cuerpo de la Válvula Corps de robinet RP6025▲ Flange Brida collerette RP70538 Valve Cartridge Válvula de Cartucho Cartouche RP6023▲ Shower Arm Brazo de Regadera Pomme de douche Brackets Abrazaderas Supports RP70536▲ Showerhead Cabeza de Regadera Pomme de douche RP70531▲ Lever Handle w/Set Screw Palanca con Tornillo de Ajuste Manette avec vis de calage RP70533▲ Trim Sleeve Manguito Manchon de Finition Trim Sleeve Manguito Manchon de
PAGE 7
and apply or attach the label to the back side of the closet cabinet door and the warning label to the hot water heater. Leave this instruction sheet for the owner's/user's reference. THIS VALVE MEETS OR EXCEEDS THE FOLLOWING STANDARDS: ANSI A112.18.1, CSA B125 AND ASSE1016 CAUTION: This system/device must be set by the installer to insure safe, maximum temperature. Any change in the setting may raise the discharge temperature above the limit considered safe and may lead to hot water burns.
PAGE 8
Peerless® Lifetime Faucet and Finish Limited Warranty All parts and finishes of the Peerless® faucet are warranted to the original consumer purchaser to be free from defects in material & workmanship for as long as the original consumer purchaser owns their home. Peerless Faucet Company recommends using a professional plumber for all installation & repair.