Installation and Assembly: Tray Style Projector Mount Models: PSMU-PRS, PSMU-PRS-S, PSMU-PRS-W Max Load Capacity: 30 lb (13.6 kg) 2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer service at 1-800-865-2112.
IMPORTANT! Read entire instruction sheet before you start installation and assembly. Before you start check the parts list below to make sure all of the parts shown are included.
1 Remove the lock plug (C) by turning the key counterclockwise. Open the top cover and attach connection block (Z) to tray (B) using two #10-32 x 3/8" serrated washer head socket pin screws (E) as shown. NOTE: Make sure that the connection block shoulder is facing the back of projector.
Installation To Wood Joist Ceilings WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that projector mount assembly is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). • Make sure that mounting screws are anchored into the center of the stud.
Installation to Concrete Ceilings WARNING • Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Place projector mount assembly (A) on ceiling as a template and mark the center of the two mounting holes. Drill two 5/16" (8 mm) dia. holes to a minimum depth of 2.5" (64 mm).
Installation to Threaded Rod (Professional installation only) 4 Thread two 3/8-16 hex thin nylon-insert locknuts (not included) on two 3/8-16 threaded rods (not included) to the desired height of projector mount assembly. Attach projector mount assembly (A) to two 3/8-16 threaded rods using two 3/8-16 hex thin nylon-insert locknuts as shown in figure 4.1 or figure 4.2. Skip to step 6.
6 Open the mount and remove thumb screw (D) as shown. NOTE: The upper tray of the mount will now slide off of the lower tray. D Installation of Projector 7 Flip projector upside down. Attach lower tray to the bottom of the projector using appropriate number of screws (K, L, M, N, O, P, Q, R or S), washers (I) and spacers (F) as shown. Use 4 mm allen wrench (T) to tighten screws. IMPORTANT: If projector does not have at least three mounting holes, do not use this tray assembly.
8 Slide upper tray into the lower tray as shown. UPPER TRAY LOWER TRAY 9 Attach thumb screw (D) to mount as shown to lock the upper tray to the lower tray.
Close the mount and insert the lock plug (C) and key (X) as shown. Turn lock plug clockwise until tightly secure. NOTE: To remove key (X), key slot must be in the horizontal position. This may require that you back off 1/4 turn. IMPORTANT: Key (X) is neccesary for projector removal. Store it in a safe place.
12 IMPORTANT: For security installations, insert one #10-32 socket pin screw (Y) through projector mount assembly (A) and into connection block (Z) as shown. Tighten screw with 4mm t-wrench (T). A Y 13 To adjust yaw (swivel) for wood stud, concrete ceiling, and threaded rod mounting applications: Loosen wood screws (V), or locknuts for threaded rods, until projector mount can be rotated. Rotate mount to desired position and retighten screws or locknuts.
