Instruction manual

- 22 -
button under the armrest while pulling out the front
bar (Fig.a). To remove the front bar, press the two
buttons under the armrests while pulling out the front
bar (Fig.b).
22• When removing the front bumper, insert the plugs
provided to close the armrests of the chassis.
23• REAR LEDGE: the rear ledge helps the mother
overcome small bumps and can also be used to carry a
second child (fig_a).
LOADING SEQUENCE: to use the PLIKO P3 COMPACT
with two children (fig_b), first set the brakes on the
stroller, then place the smaller child in the seat and
fasten the safety harness (1). Hold the handlebars (2)
and have the second child stand on the ledge (3).
• Never leave your children unattended.
• Do not allow a child to stand on the rear ledge when
the stroller is empty.
24• FOLDING UP: before folding up PLIKO P3 COMPACT,
remove the Navetta XL or the PrimoViaggio car
seat. The stroller can be folded up using one hand
only: pull first one lever upwards and then the other,
until they click.
25• Hold the central handlebar and pull it upwards until
the stroller folds up (fig_a). Check the correct closure
of the chassis from the safety hook (fig_b).
When folded, the chassis will stand upright .
26• CARRYING: PLIKO P3 COMPACT can be conveniently
carried by the central handle (with the front wheels set
on stationary) (fig.a). It can also be carried by the side
handle (fig_b).
27• REMOVABLE LINING: To remove the lining from the
stroller:. unhook the sack attachments from the
armrests in the order indicated (fig_a);. unfasten the
sack button at the sides;. remove the sack from the
footrest;. slide the leg divider part of the strap from
under the seat (fig_b);
28• unfasten the sack buttons from the seat;. unscrew the
strap (only on one side),by keeping your finger under
the nut; slide it downwards
HOW TO ASSEMBLE YOUR MODULAR SET:
Your Compact Pliko P3 COMPLETE version can be
turned into a chassis that can be used for the other parts
of the MODULAR SET (the XI Carrycot and Car Seat).
Ganciomatic System
Ganciomatic is the quick and practical system that
allows you to attach the Navetta XL or the Primo
Viaggio Tri-Fix, which are also equipped with the
Ganciomatic system, to the Pliko P3 in stroller format,
thanks to its Ganciomatic connectors.
29•
THE STROLLER GANCIOMATIC FASTENERS:
to raise the Ganciomatic connectors on the stroller, lift
the fabric covering at the corners of the seat, pull the
lever outwards and at the same time swivel the two
connectors upwards until they click (fig_a).
To lower the stroller Ganciomatic fasteners, pull
the lever outwards and at the same time rotate the
fasteners downwards (fig_b).
How to transform the pushchair into a
chassis:
- remove the pushchair’s lining (step 27/28);
- unfasten the hood and the apron if fastened;
30• Release the base by pressing the button located at
the rear of the chassis (fig_a), both on the right and
left bars. Lift the backrest upwards from the base with
both hands.
Press the two buttons on the chassis seat with both
hands and lift the entire base upwards (fig_b).
PLIKO 3 COMPACT + XL Carrycot:
To attach the carrycot to the chassis you must:
- block the PLIKO P3 COMPACT
- lift the Ganciomatic clasps in the frame
- remove the bumper bar (step 21) and insert the tops
into the chassis armrests.
31• Turn the two levers on the back of the chassis
outwards (fig_a)
- raise the footrest to its highest position;
- hold the Navetta by its handlebar;
32• place the Navetta on the Ganciomatic hooks on the
stroller, keeping the head of the bassinet unit on the
opposite side from the stroller handlebars;
- press down with both hands on the sides of the
Navetta, until it clicks into place (fig_a);
- to remove the Navetta from the chassis and for more
information, please refer to the instruction manual.
PLIKO P3 COMPACT + Primo Viaggio Tri-Fix:
To attach the car seat to the chassis you must:
- block the chassis
- lift the Ganciomatic clasps in the frame
- put the car seat in face-mum position and push it
downwards until it clicks (fig_b)
- Do not remove the bumper bar from the pushchair
when you attach the car seat (please read step 20 for
information on how to put on the bumper bar)
- Remove the car seat according to the car seat’s
instructions
When the child is older you can transform the
chassis into a PUSHCHAIR:
33• ASSEMBLY: to convert the Pliko P3 chassis version into
a stroller, check that the two levers are lowered (fig_a).
Position the backrest with the cover on the chassis seat
(fig_b).
34• To attach the backrest to the chassis (fig_a) insert the
two ends, pressing the two buttons, into the chassis
seat, as shown in figure 1, until they click into position,
as shown in figure 2. To attach the back adjustment
bar to the chassis (fig_b), rotate the attachment
upwards (figure 2, as shown by the arrow) and position
it behind the rear upright.
• Push the two fasteners down until they click into
position in the seats in the rear uprights (fig_c).
Put the lining back on, doing the opposite of what is
described in points 27 and 28.
35• If, in the PUSHCHAIR mode, you wish to attach the
XL CARRYCOT or PRIMO VIAGGIO TRI FIX using the
Ganciomatic system, lower the backrest of the pushchair
before doing anything else. As shown in step 29.
SERIAL NUMBERS
36• Behind the PLIKO P3 COMPACT backrest information
relating to product name, date of manufacture and
serial number of the product are provided. This
information is required for any complaints.