USA Istructions for use EN (LF) PRIMO VIAGGIO SIP 30•30 Side Impact Protection O W N E R ’ S WARNING: Do not install or use this infant restraint until you read and understand all instructions in this manual. To avoid serious injuries to your baby, follow the instructions carefully and be sure to buckle your baby using the 5-point harness.
Table of Contents 3 Before You Start 23 4 Customer Service 25 Installing the Car Seat without the Base 4 Registration Form 27 Installing the Seat with Different Types of Seat Belts 5 Safety 7 Safety Rules 8 Your Car Seat 9 Your Car Seat Base 10 Travel System 11 Serial Numbers 12 Installation Instructions 13 Installing the Base 14 How to Install the Base Using the LATCH SYSTEM Installing the Car Seat on the Base 28 How to Buckle Your Baby into the Car Seat 33 ow to Raise or Lo
Before You Start 1 Please read this manual carefully. Keep this manual in the plastic pocket on the base of the infant car seat. 2 Review car seat parts and read through instructions. Also read the labels. Read and understand all instructions before using this car seat. 3 Fill in and return the registration form (see page 4). 4 All assembly must be performed by an adult. 5 Do not use the car seat if damaged or parts are missing. 6 Use only the parts or accessories that come with the unit.
Customer Service Registration Form Call Peg Perego USA customer service at 1-800-671-1701 (toll free) for information about repairs or spare parts. If any part is missing or damaged, replace with Peg Perego parts only. See page 46 for a list of replacement parts. Important! Child restraints could be recalled for safety reasons. You must register this restraint to be reached in a recall.
Safety Warning • This car seat meets or exceeds all applicable Federal Motor Vehicle Safety Standard 213 requirements for use in motor vehicles and aircraft. • Your child could be seriously injured if you do not follow instructions and warning labels correctly. • Use this car seat rear facing only. This seat is not designed to face forward. Serious injury or death can occur in an accident if you install the seat facing forward. • Never use in a vehicle seat with an active air bag.
vehicle manual. According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions. • Install this car seat on front facing seats only. Do not use on rear facing or side facing seats or in cars with door-mounted or motorized shoulder belts. • If you use a lap belt or lap/shoulder belt to install the base, you must use a seat belt that locks in place. If it does not lock in place, use the locking clip.
Safety Rules • Use only with children who weigh between 5 and 30 pounds (2.3 and 13,5 kg) and whose height is 30 inches (76 cm) or less. If your baby was born with low birth weight, ask your doctor for special instructions on using an infant car seat. • Use this car seat in vehicles with standard lap or lap/shoulder belts or universal lower anchors. If your vehicle has lower anchors, use those to secure the car seat instead of the standard seat belt. Read your vehicle manual to locate the lower anchors.
Your Car Seat HOOD 5-POINT HARNESS SYSTEM Chest harness clip Harness latch plate Harness buckle FRONT BACK Seat handle Side Impact Head protection Release lever Harness strap Anchor buckles Seat pad for infant Slide adjuster Harness adjuster button Harness adjuster strap 8 Energy absorbing Expanded Polystyrene (EPS) foam lined shell and headrest for added impact protection.
Your Car Seat Base SIDE Belt slots with anti-slip rubber pads LOCKING CLIP STORAGE Level indicator BACK FRONT Level knob Locking clip Latch strap Anchor latches Owner's Manual book pocket 9
Travel System Seat Duette SW Triplette SW Aria Twin 6040 Si Pliko Mini Vela easy drive Base 10 Pliko Four Switch Four Uno GT3 Skate Book Book Plus
Serial Numbers The following information can be found under the front of the seat of the Primo Viaggio Sip 30•30 : product name, production date and serial number. Buckle production date. Harness production date. In the event of problems with the product, these details will be of use to customers.
Installation Instructions Peg Perego Primo Viaggio Sip 30•30 is certified for use with or without the base. Use of the base is highly recommended because it makes installation easier and therefore safer.
Installing the Base When using Primo Viaggio Sip 30•30 with its base, first you install the base, and then you install the car seat on the base. Important! Read your vehicle manual for instructions on where to best install an infant car seat in your vehicle. There are two ways to install the base: I USING THE LATCH SYSTEM. If your car has “universal lower anchors”, you can install the infant car seat using the LATCH system instructions on page 14.
I - How to Install the Base Using the LATCH SYSTEM Install the base with your vehicle parked on level ground. 1• T ake the car seat off the base by moving the handle to the upright position. Place your hand on the top of the seat back and pull up on the handle with your fingers. Note: Pulling near the center of the handle provides the easiest release. 2• Position the base rear facing in the back seat of your vehicle.
PUSH 3• Remove the two anchor latches from their housings. The latches are on the sides of the base. First loosen the latch strap by pressing on the gray button and pulling the strap as shown. Then press the red button on top of the latch and pull the latch out of its housing. Repeat on other side. B A PU SH A B 4• Push each latch onto the anchor bar located between your vehicle seat back and seat bottom. Press until you hear the click.
5• Make sure that the latch strap is threaded flat against the base. 6• Tighten the base against the seat by pulling the free end of the latch strap. Press down on the base with your body weight and tighten further. Check the level indicator. If the pointer has moved outside of the green area, turn the knob until the pointer is back within the green area. You may need to loosen the strap slightly to do this. Push and pull on the base.
II - How to Install the Base Using Your VEHICLE SEAT BELT Important! Not all seat belts work the same way. To make sure that the infant car seat is properly installed using your seat belts, read your vehicle owner’s manual. It will suggest proper placement of an infant car seat in your particular vehicle. Park your vehicle on level ground. 1• Take the car seat off the base by moving the handle to the upright position. Place your hand on the top of the seat back and pull up on the handle with your fingers.
3• Thread the lap belt through the slots on the base and lock the latch plate into the buckle as shown. 4• Pull the strap to tighten the seat belt. Press down on the base with your body weight and pull the strap tighter. Then push and pull on the base. If you can move the base more than 2,5 cm (1 inch), tighten the belt further. Once the base is tight, check the level indicator. If the pointer has moved outside of the green area, turn the knob until the pointer is back within the green area.
Installing the Base with Different Types of Seat Belts Primo Viaggio Sip 30•30 is designed for use with lap or lap/shoulder seat belts. Four of the most common types are listed below. Please read your vehicle manual for instructions on installing an infant car seat using your vehicle seat belts.
III Lap/shoulder belt with a locking latch plate If you have a lap/shoulder belt with a locking latch plate and the belt comes loose after buckling, unbuckle it, flip it over, and re-buckle. This will usually keep the seat belt locked in place. If not, read your vehicle manual for specific instructions. IV Different Types of Lap Belts Lap belts with Emergency Locking Retractors (ELR), Automatic Locking Retractors (ALR), and Switching Locking Retractors (SLR) look as shown.
How to Install the Locking Clip B PUS H To install the locking clip, hold the shoulder strap and lap belt together just above the buckle. Unbuckle the belt while holding the straps. Hook the locking clip around both straps as shown. A Leave 1/2 inch space between the clip and latch. Re-buckle the belt.
Different Types of Vehicle Seat Belts Important! Do not install this car seat on seats with: A Lap/motorized shoulder belts. B Belts mounted on the door. C Side-facing seats. D Rear-facing seats or seats that rotate. For your child’s safety, always read your vehicle manual for instructions on installing child car seats.
Installing the Car Seat on the Base Now that you have installed the base in your vehicle, you are ready to install the car seat on the base. 1• Holding the car seat by the handle, press it rear facing on the base until you hear the click. You will not be able to move the car seat if it is properly locked in place. Check to make sure the base is still level. If not, remove the car seat and properly adjust the base. Important! Newborn infants should be properly reclined.
2• Adjust the handle so it rests at the top edge of the car seat as shown. Any other position may injure your baby in an accident. To rotate the handlebar, press each of the round buttons (located on each side of the handle where it attaches to the seat) and rotate it to the position required. 3• To remove the car seat, move the handle to the upright position. Place your hand on the top of the seat back and pull up on the handle with your fingers.
Installing the Car Seat without the Base Important! The base is designed to avoid consumer misuse by reducing the number of times the seat must be anchored to your vehicle. Please, use and install Primo Viaggio Sip 30•30 without the base only if needed. Park the vehicle on level ground. 1• Position the restraint on the seat, so your baby is facing the rear of the vehicle. Adjust the handle so it rests at the top edge of the car seat as shown. Any other position may injure your baby in an accident.
2• Adjust the restraint on the seat. Check the red line to see that the base is level with the ground. Thread the lap belt through the slots on the seat and lock the latch plate into the buckle as shown. 3• Pull the strap to tighten the seat belt. Press down on the seat with your body weight and pull the strap tighter. Once the seat is tight, check that the red line on the side of the car seat is level with the ground.
Installing the Seat with Different Types of Seat Belts Installation of Primo Viaggio Sip 30•30 without base follows the same rules as with base regarding the availability of different types of vehicle seat belts. Important! For different types of seat belts, please refer to page 19 and 20. Should your vehicle belt need a locking clip, please refer to page 21 for installation details. Illustration in this page shows the completed installation.
How to Buckle Your Baby into the Car Seat This restraint uses a 5-point harness system to secure your baby into the car seat. See illustration on page 8. 1• Push the red buckle button to release the harness. Press and hold the harness adjuster button while pulling the shoulder straps out undo the chest clip (point 5). Lay the shoulder straps to the side to make room for your baby. 2• Put your baby in the car seat with their bottom and back flat against the child restraint.
3• I nsert both latch plates into the buckle until you hear them click. Pull on straps to make sure that both plates are latched securely. (Note: You may need to adjust the shoulder height. See How to Raise or Lower the Shoulder Straps on page 33). 4• Latch the two chest clips together.
5• To undo the chest clip, press the button on the clip and pull apart as shown. B PUSH A 6• To undo the latch plates, press the red button and pull the latches up.
7• A djust the chest clip to the arm pit level. To tighten the harness, pull the adjuster strap at the bottom of seat until strap is snug. Make sure you leave one finger width between the harness and your baby’s collar bone. Tuck the loose end of the adjuster strap under the seat padding. 8• To loosen the harness, press and hold the harness adjuster button inside the slot located at your baby’s feet, and pull the top harness as shown.
Important! A snug strap should not allow any slack. It lies in a relatively straight line without sagging. It does not press on the child’s flesh or push the child’s body into an unnatural position.
How to Raise or Lower the Shoulder Straps Primo Viaggio Sip 30•30 is fitted with a new and innovative feature to make strap adjustment easy and safe. Removing the shoulder strap and threading through the slots is not required anymore. B A 1• To raise or lower the harness strap, push the button on top of the back plate and at the same time pull or push the plate to adjust at the desired position. There are 5 positions to choose from.
Important! The seat is supplied with a filler cushion for new-born babies. This can be removed when the child grows. Even when using the cushion make sure the shoulder straps are positioned correctly. 34 ⇠ n mi Important! Make sure that the chest harness and all straps are flat and not twisted on the back or the front of the car seat. h nc Important! This restraint is designed for infants up to 76 cm (30 inches) in length. The top of the infant head should not exceed the top of the seat back.
Using the Car Seat Outside the Vehicle This unit can be used as an infant seat. The special shell shape is designed for rocking your baby. The hood provides shade for your baby. 1• To rock your baby, move the handle into the up position as shown. To prevent rocking, lock the handle behind the backrest.
2• To attach the hood, push the hood latch into the slot on the seat shell as shown. To open the hood, pull the frame until it clicks open. 3• To adjust the hood position, simply push into the desired position. 4• To remove the hood, push the buttons and remove the latches from the seat shell. Warning! The hood must not be used to lift the safety seat because it might detach.
5• Carrying handle for Base. Warning! Do not use with the seat attached to the base. Warning! Do not use as a means of transporting child.
How to Use the Car Seat on Aircraft without Base This unit is certified for aircraft use. 1• P osition the restraint on the seat, adjust the handle so it rests at the top edge of the car seat as shown. Any other position may injure your baby in an accident. To move the handle, press the gray buttons on the sides of the handle at the same time and push the handle. 2• Adjust the restraint on the seat. Check the red line to see that the base is level with the ground.
How to Use the Car Seat on Aircraft with Base This unit is certified for aircraft use. 1• Buckle the base to the aircraft seat using the lap belt as shown. A secondary belt path can also be used as shown in Fig. B. A 2• Position the base rear facing in the aircraft seat. Check the level indicator on the side of the base to make sure that the ball is in the green area. If it is not, turn the knob left or right until it is in the correct position.
tighten the belt further. Position the car seat rear facing over the base. Press the seat into the base until you hear the click. Make sure the seat is correctly locked in place. Important! Follow the harness instructions beginning with “How to Buckle Your Baby into the Car Seat” (on page 28) to safely secure your baby.
Cleaning and Maintenance This unit needs minimal maintenance. • Keep all moving parts clean. Lubricate with light oil, if necessary on moving parts. • Clean the plastic parts often with a damp cloth. Do not use solvents or harsh products. • Brush the fabric parts to remove dust. • Protect the product against snow, water, and rain. Constant exposure to sunlight can change the colors in the material. Sun can also make the seat very hot. Be sure it is cool before putting your baby in the seat.
How to Wash the Chair Padding - Cover removal 1• Remove the hood. • Remove the filler cushion. • Press the red button on the crotch strap buckle to release the harness. • remove the shoulder straps from the slide adjuster on the back of the seat. • open the chest clip. • from the front, remove the straps from the backrest. 2• Slide on the headrest cover from the bottom first and then, carefully, from the two side tabs. BE CAREFUL NOT TO BREAK THE WHITE POLYSTYRENE (EPS) PARTS.
3• Remove the four installation tabs of the padding from the edge of the car seat. • Remove the two covers of the lateral guides for the belt of the car. 4• Slip the side belts out through the slots in the cover; finally, also slip the central strap out through the hole in the cover. • remove the padding in sequence, as shown.
How to Wash the Chair Padding - Refitting 1• Slide the padding on in sequence, as shown: - slide the sack on from the top - first put the lateral tabs of the headrest carefully _ then slide it into the bottom of the headrest. • Insert the side belts upwards into the slots in the cover. • Slip the strap through the opening in the cover and insert it into the leg divider. 2• Insert the four installation tabs of the padding from the edge of the car seat.
3• To slide on the headrest cover from the two lateral tabs and slide on the bottom. 4• IMPORTANT: the strap must not be twisted. • Insert the straps in the backrest, from the front . • Attach the shoulder straps with Velcro. • Insert the safety belts into the slide adjuster on the back of the seat.
Replacement Parts 1 1) BSAKAP* 2) SPST6850GL 3) SPST6341DNF 4) SPST6341SNF 5) BSPKAP* 6) BCAASI* 7) MUCI0081GR 8) BRIASI* 9) ASPI0151GLNF 10) IAKADJUSNF 6 4 3 9 2 5 7 8 10 46 NOTE: Spare parts available in different colors* to be specified when ordering. NOTE: A Tether is not a component of a rear facing only car seat.
47
1 4 Piezas de repuesto 6 3 9 1) BSAKAP* 2) SPST6850GL 3) SPST6341DNF 4) SPST6341SNF 5) BSPKAP* 6) BCAASI* 7) MUCI0081GR 8) BRIASI* 9) ASPI0151GLNF 10) IAKADJUSNF 2 5 7 8 NOTA: Cuando haga su pedido especifique los colores* de las piezas de repuesto. 10 NOTA: Un Tether no es un componente de silla de auto orientada hacia atrás.
3• Para calzar el revestimiento del reposacabeza comenzar por las dos aletas laterales y finalmente calzar la parte inferior. 4• IMPORTANTE: El cinturón no debe estar torcido. • Colocar los cinturones en el respaldo, como se muestra en la figura. • Enganchar las cintas de los hombros con velcro. • Poner los cinturones de seguridad en el seguro del lado posterior del respaldo.
Cómo lavar el acolchado de la silla - Enfundar 1•Calzar el acolchado en secuencia, como se muestra en la figura: - calzar desde arriba el saco; - introducir primero las aletas laterales del reposacabeza con cuidado; - luego hacerlo pasar por la parte inferior del reposacabeza. A B C • Hacer pasar los cinturones laterales de abajo hacia arriba por la ranura del saco. • Hacer pasar la correa por la abertura del saco e insertarla en el separador de las piernas.
3•Sacar las cuatro aletas de fijación del acolchado del borde de la sillita de coche. • Quitar las dos tapas de las guías laterales del cinturón del coche. 4• Extraer los cinturones laterales haciéndolos pasar por las ranuras del saco; por último, extraer también la correa central por la ranura del saco. • Extraer el acolchado en secuencia, como se muestra en la figura. C B Mantenimiento del acolchado • Laver à la main uniquement, température maximale 30°C.
Cómo lavar el acolchado de la silla - Desenfundable 1•Retire la capota. • Sacar el cojín de relleno. • Pulsar el botón rojo de la hebilla entrepiernas para desabrochar el cinturón de seguridad. • Sacar los tirantes del seguro deslizante del lado posterior de la silla. • Quitar las cintas de los hombros. • Sacar los cinturones del respaldo por delante. 2•Sacar el revestimiento del reposacabeza, primero por la parte inferior y luego, con cuidado, de las dos aletas laterales.
Limpieza y mantenimiento Esta unidad requiere un mantenimiento mínimo. • Mantenga limpias todas las partes móviles. Lubrique las partes móviles con un aceite liviano si es necesario. • Limpie las partes plásticas con frecuencia utilizando un paño húmedo. No utilice solventes ni productos fuertes. • Cepille las partes de tela para eliminar el polvo. • Proteja el producto de la nieve, el agua y la lluvia. La exposición constante a la luz solar puede cambiar los colores del material.
más. Controle el nivel y ajústelo si es necesario. Empuje y tire de la base. Si se desplaza más de una pulgada, apriete el cinturón aún más. Coloque la silla de auto orientada hacia atrás sobre la base. Empuje la silla sobre la base hasta oír el clic del enganche. Asegúrese de que la silla esté correctamente bloqueada en su lugar. Importante! Siga las instrucciones del arnés sobre «Cómo sujetar a su bebé en la silla de auto» (página 28) para sujetar a su bebé correctamente.
Uso de la silla de auto en el avión con la base Esta unidad está certificada para el uso en aviones. 1• Abroche la base al asiento del avión utilizando el cinturón de cadera como muestra la figura. Puede utilizarse un paso secundario para el cinturón como indica la figura B. A 2• Coloque la base orientada hacia atrás en el asiento del avión. Controle el indicador de nivel al costado de la base para asegurarse de que la bola esté en el área verde.
Uso de la silla de auto en el avión sin la base Esta unidad está certificada para el uso en aviones. 1• Coloque el dispositivo de retención sobre el asiento y ajuste el asa de modo que descanse sobre el borde superior de la silla de auto como indica la figura. Cualquier otra posición puede provocar heridas al bebé en un accidente. Para mover el asa, pulse simultáneamente los botones grises laterales y empújela. 2• Ajuste el dispositivo de retención en el asiento.
5• Asa de transporte para la base. Advertencia! No la utilice con la silla acoplada a la base. Advertencia! No la utilice como medio para transportar al niño.
2• Para montar la capota, empuje el seguro de la capota en la ranura de la silla como indica la figura. Para abrir la capota, tire del armazón hasta que se abra con un clic. 3• Para ajustar la posición de la capota, simplemente empújela a la posición deseada. 4• Para quitar la capota, pulse los botones y quite los seguros de la silla. B A A Importante: la capota no tiene que usarse para levantar la silla ya que puede soltarse.
Uso de la silla de auto fuera del vehículo Esta unidad puede utilizarse como silla para niños. Está diseñada con forma de caparazón para acunar al bebé. La capota hace sombra. 1• Para acunar a su bebé, levante el asa como indica la figura. Para impedir el balanceo, bloquee el asa detrás del respaldo.
a ulg 1p .54 2 da 2• La posición correcta es aquella en la que la ranura de la correa de hombro queda precisamente debajo del nivel del hombro como indica la figura. ce 2 3 4 5 os etr 1 m ntí Importante! Este dispositivo de retención está diseñado para niños de hasta 30 pulgadas de estatura. La cabeza del niño no debería sobrepasar el respaldo de la silla. Importante! Asegúrese de que el arnés pectoral y todas las correas queden planos y no retorcidos detrás o delante de la silla de auto.
Cómo levantar o bajar las correas de hombro Primo Viaggio Sip 30•30 está dotada de una prestación innovadora para que el ajuste de las correas sea fácil y seguro. Ya no es necesario quitar la correa de hombro y hacerla pasar por las ranuras. B A 1• Para levantar o bajar la correa del arnés, pulse el botón de la placa posterior y al mismo tiempo tire o empuje la placa para ajustarla en la posición deseada. Hay 5 posiciones para elegir.
Importante! Una correa ceñida no debería permitir ningún aflojamiento sino mantener una línea relativamente recta sin ceder, pero sin tampoco hacer presión sobre el bebé ni empujar el cuerpo a una posición que no sea natural.
7• Ajuste el clip pectoral al nivel de la axila. Para apretar el arnés, tire de la correa de ajuste del fondo de la silla hasta que quede ceñida. Asegúrese de dejar un dedo de distancia entre el arnés y la clavícula del bebé. Meta el extremo suelto de la correa de ajuste debajo del acolchado de la silla. 8• Para aflojar el arnés, pulse y mantenga pulsado el botón de ajuste del arnés dentro de la ranura ubicada a los pies de su bebé y tire del arnés como indica la figura.
5• Para desabrochar el clip pectoral, pulsar el botón del clip y tirar como indica la figura. A B EMPUJAR 6• Para desabrochar las placas del seguro, pulse el botón rojo y tire hacia arriba.
3• Introducir ambas placas de cierre en la hebilla hasta oír el clic. Tirar de las correas para asegurarse de que ambas placas estén correctamente enganchadas. (Nota: Puede que deba ajustar la altura del hombro. Consultar Cómo Subir o Bajar los Tirantes en la página 33). 4• Abroche los dos clips pectorales.
Cómo sujetar a su bebé en la silla de auto Este dispositivo de retención aplica un sistema de arnés de 5 puntos para sujetar al bebé en la silla de auto. Vea la ilustración en la página 8. 1• Pulse el botón rojo de la hebilla para abrir el arnés. Mantenga pulsado el botón de ajuste del arnés mientras tira de las correas de hombro desabrochar el clip pectoral (punto 5). Coloque las correas de hombro al costado para dar lugar a su bebé.
Instalación de la silla con diferentes tipos de cinturones de seguridad Primo Viaggio Sip 30•30 sin base se instala del mismo modo que con base en función de la disponibilidad de los diferentes cinturones de seguridad. Importante! Para otros tipos de cinturón, consulte las páginas 19 y 20. Si el cinturón necesita una presilla de bloqueo, ver página 21 para las instrucciones de instalación. El ejemplo que figura en esta página muestra una instalación completa.
2• Ajuste el dispositivo de retención en el asiento. Compruebe que la base esté paralela al suelo observando la línea roja. Haga pasar el cinturón de cadera por las ranuras de la silla y bloquee la placa del seguro en la hebilla como indica la figura. 3• Tire de la correa para apretar el cinturón de seguridad. Presione la silla con el peso de su cuerpo para apretar la correa aún más. Una vez ajustada la silla, compruebe que la línea roja al costado de la silla quede paralela al suelo.
Instalación de la silla de auto sin la base Importante! La base está diseñada para evitar el uso erróneo, ya que evita tener que fijar la silla en el vehículo cada vez que se utiliza. Utilice e instale Primo Viaggio Sip 30•30 sin la base sólo en caso de necesidad. Aparque el vehículo sobre un terreno llano. 1• Coloque el dispositivo de retención sobre el asiento de modo que quede orientado hacia atrás. El asa debe descansar sobre el borde superior de la silla de auto como indica la figura.
2• El asa debe descansar sobre el borde superior de la silla de auto como indica la figura. Cualquier otra posición puede provocar heridas al bebé en un accidente. Para mover el asa presione los botones redondos del asa colocándolo simultáneamente en la posición deseada. 3• Para quitar la silla de coche, colocar la palanca en posición vertical. Situar la mano en la parte superior del respaldo y tirar de la palanca con los dedos.
Instalación de la silla de auto sobre la base Ahora que la base está instalada en su vehículo, puede instalar la silla de auto sobre la base. 1• Sosteniendo la silla de auto por el asa, móntela orientada hacia atrás presionándola sobre la base hasta oír el clic. Si la silla de auto está bien bloqueada, no debería ser posible moverla. Compruebe que la base esté todavía nivelada correctamente. De lo contrario, quite la silla de auto y ajuste la base adecuadamente.
Diferentes tipos de cinturones de seguridad Importante! No instale esta silla de auto en asientos con: A C inturones de cadera/hombro motorizados. B Cinturones montados en la puerta. C Asientos orientados hacia los costados. D Asientos orientados hacia atrás o giratorios. A B Para la seguridad de su niño, siempre lea en el manual de su vehículo las instrucciones de instalación de sillas de auto para niños.
Cómo instalar el clip de bloqueo B R UJA EMP Para instalar el clip de bloqueo, sostenga la correa de hombro y el cinturón de cadera juntos, sobre la hebilla. Desabroche el cinturón sosteniendo las correas. Enganche el clip de bloqueo en torno a ambas correas como indica la figura. A Deje media pulgada entre el clip y el seguro. Abroche de nuevo el cinturón.
clip de bloqueo (guardado en la base de la silla) para poder asegurarlo adecuadamente (página 21). III Cinturón de cadera/hombro con placa de seguro con bloqueo Si tiene un cinturón de cadera/hombro con placa de seguro con bloqueo y el cinturón queda suelto después de abrocharlo, desabróchelo, inviértalo y vuelva a abrocharlo. De este modo el cinturón debería quedar bloqueado. Si no, lea instrucciones más específicas en el manual de su vehículo.
Instalación de la base con diferentes tipos de cinturones de seguridad Primo Viaggio Sip 30•30 está diseñada para utilizarse con cinturones de seguridad de cadera o de hombro. A continuación se listan cuatro de los tipos más comunes. Lea el manual de instrucciones de su vehículo para saber cómo instalar una silla de auto para niños utilizando los cinturones de seguridad del vehículo.
izquierda o la derecha hasta que esté en la posición correcta. 3• Haga pasar el cinturón de cadera por las ranuras de la base y bloquee la placa del seguro en la hebilla como indica la figura. 4• Tire de la correa para apretar el cinturón de seguridad. Presione la base con el peso de su cuerpo para apretar la correa aún más. Empuje y tire de la base. Si la base se desplaza más de una pulgada, apriete el cinturón aún más. Con la base bien apretada, controle el indicador de nivel.
II - Cómo instalar la base utilizando los CINTURONES DE SEGURIDAD DEL VEHÍCULO Importante! No todos los cinturones de seguridad funcionan de la misma manera. Para asegurarse de que la silla de auto para niños esté bien instalada con los cinturones de seguridad, lea el manual de su vehículo. El manual le indicará cómo montar la silla de auto correctamente en su vehículo. Aparque el vehículo sobre un terreno llano. 1• Quitar la silla de coche de la base colocando la palanca en posición vertical.
5• Asegúrese de que la correa del seguro esté colocada planamente contra la base. 6• Apriete la base contra el asiento tirando del extremo libre de la correa de seguridad. Empuje la base con el peso de su cuerpo para apretarla más. Controle el indicador de nivel. Si se hubiese salido del área verde, gire el pomo hasta que el indicador vuelva a estar dentro del área. Para ello puede ser necesario aflojar la correa ligeramente. Empuje y tire de la base.
EMPUJAR 3• Quite los dos seguros de anclaje de sus alojamientos. Los seguros están a los costados de la base. Primero afloje la correa del seguro pulsando el botón gris y tirando de la correa como indica la figura. Pulse el botón rojo sobre el seguro y quite el seguro de su alojamiento. Repita la operación del otro lado. B A EM PU JA R A B 4• Empuje cada seguro en la barra de anclaje ubicada entre el respaldo y el fondo del asiento de su vehículo. Presione hasta oír el clic.
I - Cómo instalar la base utilizando el sistema de seguro LATCH SYSTEM Instale la base con el vehículo aparcado sobre un terreno llano. 1• Quitar la silla de coche de la base colocando la palanca en posición vertical. Situar la mano en la parte superior del respaldo y tirar de la palanca con los dedos. Nota: La silla se quitará con más facilidad si se tira cerca del centro de la palanca. 2• Coloque la base orientada hacia atrás sobre el asiento trasero del vehículo.
Instalación de la base Para utilizar Primo Viaggio Sip 30•30 con la base, primero hay que instalar la base y luego la silla de auto sobre la base. Importante! Lea el manual de instrucciones de su vehículo para saber en qué parte del vehículo se puede instalar mejor una silla de auto para niños. Hay dos maneras de instalar la base: I CON EL sistema de seguro LATCH SYSTEM.
Instrucciones de instalación Peg Perego Primo Viaggio Sip 30•30 está certificada para utilizarse con o sin base. Se recomienda utilizar la base para que la instalación resulte más fácil y, por lo tanto, segura.
Números de Serie Primo Viaggio Sip 30•30 contiene debajo de la parte delantera de su asiento las siguientes informaciones: Nombre del producto, fecha de fabricación y número de serie. Fecha de fabricación de la hebilla. Fecha de fabricación del arnés. Estos elementos son de utilidad para el consumidor en caso de que el producto presente anomalías.
Sistema de Viaje Silla Duette SW Triplette SW Aria Twin 6040 Si Pliko Mini Vela easy drive Pliko Four Switch Four Uno GT3 Skate Book Book Plus Base 10
Base de la silla de auto LATERAL Ranuras para cinturón con goma antideslizante DEPÓSITO DE CLIP DE BLOQUEO Indicador de nivel POSTERIOR FRONTAL Pomo de nivel Clip de bloqueo Correa de seguro Seguros de anclaje Bolsillo para manual del usuario 9
Silla de auto SISTEMA DE ARNÉS DE 5 PUNTOS CAPOTA Clip de arnés pectoral Placa de seguro del arnés Hebilla del arnés FRONTAL Asa de la silla POSTERIOR Palanca de apertura Protección de cabeza contra impacto lateral Correa del arnés Hebillas de anclaje Almohadillas para el niño. Regulador deslizante Botón de ajuste del arnés Correa de ajuste del arnés Estructura revestida en espuma de poliestireno expandido (EPS) que absorbe energía, con reposacabezas para una mayor protección contra el impacto.
Reglas de seguridad • Utilice el dispositivo sólo con niños de 5 a 30 libras (2,3 a 13,5 kg) de peso y hasta 30 pulgadas (76 cm) de estatura. Si su bebé tiene muy poco peso, pida al médico instrucciones especiales sobre cómo utilizar una silla de auto. • Utilice esta silla de auto en vehículos con cinturones de cadera o de hombro estándar o con anclajes inferiores universales. Si su vehículo tiene anclajes inferiores, utilícelos para asegurar la silla de auto en vez de utilizar el cinturón de seguridad.
sean las instrucciones del manual de su vehículo. Según las estadísticas de accidentes automovilísticos, cuando los niños están sujetados correctamente en el asiento trasero, se encuentran más a salvo que en el asiento delantero. • Instale esta silla de auto únicamente en asientos orientados hacia delante. No la utilice en asientos orientados hacia atrás o hacia los costados, ni en vehículos con cinturones de hombro motorizados o montados en las puertas.
Advertencia Seguridad • Esta silla de auto es conforme o supera todos los requisitos de la Norma Federal de Seguridad de Vehículos 213 para el uso en vehículos de motor y aviones. • Su niño podría sufrir graves heridas en caso de incumplimiento de las instrucciones y etiquetas de advertencia. • Utilice esta silla de auto únicamente orientada hacia atrás. Esta silla no está diseñada para orientarse hacia delante.
Servicio al cliente Formulario de registro Peg Perego U.S.A., Inc. 3625 Independence Drive Fort Wayne, IN 46808 Si desea tener más de una base, puede adquirirla a través de su revendedor local, o llamando al 1-800-671-1701 (gratuito) o visitando www.pegperego.com. Importante! Los dispositivos de retención para niños pueden ser reclamados para actualizaciones por motivos de seguridad. Registre este dispositivo de retención para permitir que le llamen.
Antes de empezar 1 Lea este manual atentamente. Conserve este manual en el bolsillo plástico de la base de la silla de auto. 2 Revise una a una las piezas de la silla de auto y lea las instrucciones. Lea también las etiquetas. Lea y entienda todas las instrucciones antes de utilizar esta silla de auto. 3 Rellene y envíe el formulario de registro (página 4). 4 El ensamblaje debe ser llevado a cabo por un adulto. 5 No utilice la silla de auto si falta o si está dañada alguna pieza.
Tabla de contenidos 3 Antes de empezar 4 Servicio al cliente 4 Formulario de registro 5 Seguridad 7 Reglas de seguridad 8 Silla de auto 9 Base de la silla de auto 10 Sistema de Viaje 11 Números de Serie 12 Instrucciones de instalación 13 Instalación de la base 14 Cómo instalar la base utilizando el sistema de seguro LATCH SYSTEM 17 Cómo instalar la base utilizando los CINTURONES DE SEGURIDAD DEL VEHÍCULO 19 Instalación de la base con diferentes tipos de cinturones de seguridad 21 Cómo instala
USA Instrucciones de uso ES (LF) PRIMO VIAGGIO SIP 30•30 Side Impact Protection M A N U A L ADVERTENCIA: D E L No instale ni utilice este dispositivo de retención para niños sin antes leer y entender todas las instrucciones de este manual. Para evitar heridas graves a su bebé, siga las instrucciones atentamente y asegúrese de sujetar a su bebé con el arnés de 5 puntos.