Installation Guide

Tools: Preparation/Assembly
1
2
• Adjustable wrench
• Groove joint plier
• Pipe tape
• Phillips screwdriver
Safety Tips
Things You May Need
• If soldering during faucet installation, the seats cartridges
and
washers will have to be removed before using flame.
Othe
rwise, warranty will be void on these parts.
• Protect your eyes with safety glasses when cutting or
soldering
water supply line.
• Cover your drain to avoid loosing parts.
Important points
Prior to beginning installation, turn off the cold and hot water
lines
and open the old faucet to release build-up pressure.
When
installing your new faucet, turn the connector nuts finger-
tight,
then use one wrench to anchor the fitting and a second
wrench to tighten the nut one additional tu
rn. Connections that
are
too tight will reduce the integrity of the system.
Wrap all threaded connections with pipe tape available at
your
local hardware or plumbing supply store. Always wrap in
a clockwise direction.
a
All
installations can vary depending on how your previous faucet was installed. Not all supplies for faucet
installation are
included; however they are available wherever plumbing supplies are sold. When
choosing
your installation supplies, make sure they are IAPMO and/or CSA approved products.
noit
a
l
l
a
tsni
Maintenance
What you need to know
Steps 1-4
Need help?
For additional assistance or service call:
1 888 328-2383 USA 1 800 487-8372 CAN
8 a.m. to 8 p.m. EST Monday-Friday
9 a.m. to 5 p.m. EST Saturday & Sunday
Shut off water supply before installation.
Installation
5
Steps 5-7 Steps 8-10
Installation
Installation
Troubleshooting
Steps 11-12
Pa
rts diagram
Installation
H125 x W120mm 813-971 A
BLACK
Your new bathroom faucet is designed for
years
of trouble-free performance.
Keep
it looking new by cleaning it periodically with a soft
cloth.
Avoid abrasive cleaners, steel wool and harsh chemicals
as
these will dull the finish and void your warranty.
For models:
944-264
Remove rubber washer, metal washer and lock nut
from the spout shank.
3
Insert faucet body through the correct faucet hole in the
sink.
4
Slide the rubber washer and metal washer up the
mounting shank and secure faucet body with lock nut.
Thread adaptor assembly onto the shank.
6
Loosen screw on hose adapter at the end of flex hose,
push adapter with hose coupling until you hear a “click”.
Tighten with screw.
7
Attach weights set to hose. For best results, be sure the
sprayhead is locked in the faucet body, and attached the
weights just above the lowest part of the hose as it rises
to the spout. This will ensure pulling force all the way into
the faucet body.
8
Wrap supply inlets with pipe tape and connect to water
supply.
9
Lift plastic pump from soap dispenser connector.
Unthread the bottle, lock nut and washer from soap
dispenser connector.
10
From above sink, install soap dispenser connector through
the sink. From below, secure with washer and locknut.
11
From below sink, install bottle. Insert pump into
decorative dispenser nozzle and place assembly into
dispenser connector.
12
After installing faucet, remove pull-down spray and turn
on water to remove any leftover debris. Re-assemble
spray.
Metal Handle Assembly
Screw(M5 * 5mm L)
Trim Cap
Lock Nut
Ceramic Disc Cartridge
Spout Seal kit
O-Ring(Ø7/8" ID * Ø1-1/8" OD)
Hose Guide
Hand Spray Button
Aerator
Hand Spray W/ Check valve
O-Ring(Ø2-11/16" ID * Ø2-13/16" OD)
Lock Nut
Mounting Hardware
Shank Adaptor Assembly
O-Ring(Ø5/16" ID * Ø1/2" OD)
Check Valve
Hose Adaptor Assembly
O-Ring(Ø5/16" ID * Ø7/16" ID)
Supply Pipe-Hot
Supply Pipe-Cold
Back Flow Prevention Device
Coupling Nut
Weight
Hex Wrench (H2.5 * 19 mm L * 53 mm L)
Pipe Tape
Spray Hose
Soap Dispenser Assembly
Soap Dispenser Nozzle
Soap Pump
Soap Dispenser Sleeve
O-Ring(Ø1-1/2" ID * Ø1-11/16" OD)
Nut & Washer
Soap Bottle
A662598
A008003
A103290
A104207
A507348N
A603638
A004051
A126003
A66D097
A500841N-50
A523484N
A072013
A054062
A66D098
A66D099N
A004031N
A519204N
A663880
A004001N
A051406N
A051404N
A603661N
A009016
A504713
A031000
A203000
A512101N
A502227
A605121
A602530
A665583
A048071
A66D111
A116000
1
⊙
.
2.
3
⊙
.
4.
5.
6.
7.
8.
9.
10
⊙
.
11
⊙
.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27
⊙
.
28
⊙
.
29
⊙
.
30.
31
⊙
.
32.
33.
34.
PROBLEM
Leaks underneath handle.
CAUSE
Adjusting ring or cap have come loose or O-ring is dirty or twisted.
SOLUTION
Tighten the adjusting ring or cap. Clean or replace O-ring.
PROMBLEM
Aerator leaks or has an inconsistent water flow pattern.
CAUSE
Aerator is dirty or improperly installed.
SOLUTION
Remove aerator, check for debris in the aerator screens, and confirm the rubber washer is properly installed.
PROBLEM
Water will not shut off completely.
CAUSE
Dirty or worn out plastic washer in the cartridge.
ACTION
Remove handle and cartridge to check if ceramic disk is damage permanently or dirty. Re-install cartridge.
5.
4.
3.
1.
7.
6.
8.
9.
11.
10.
12.
13.
14.
21.
16.
17.
18.
15.
24.
25.
26.
19.
22.
23.
20.
2.
27.
29.
30.
31.
32.
28.
33.
34.
944-264 (V1)