O L- 3 0 5 4 5 -0 1 Cisco Model DPC3829 and DPC3829M DOCSIS 3.
Please Read Important Please read this entire guide. If this guide provides installation or operation instructions, give particular attention to all safety statements included in this guide.
Notices Trademark Acknowledgments Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. DOCSIS is a registered trademark of Cable Television Laboratories, Inc., and PacketCable is a trademark of Cable Television Laboratories, Inc. The Wi-Fi Protected Setup mark is a mark of the Wi-Fi Alliance. Wi-Fi Protected Setup is a trademark of the Wi-Fi Alliance.
Copyright © 2013 Cisco Systems, Inc. All rights reserved. Printed in the United States of America. Information in this publication is subject to change without notice. No part of this publication may be reproduced or transmitted in any form, by photocopy, microfilm, xerography, or any other means, or incorporated into any information retrieval system, electronic or mechanical, for any purpose, without the express permission of Cisco Systems, Inc.
Contents IMPORTANT SAFETY INSTRUCTIONS vii United States FCC Compliance xi Chapter 1 Introducing the DOCSIS Wireless Residential Gateway 1 Introduction ......................................................................................................................... 2 What's In the Carton? .......................................................................................................... 3 Front Panel Description .............................................................................
Notice to Installers The servicing instructions in this notice are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions, unless you are qualified to do so. Notice à l’attention des installateurs de réseaux câblés Les instructions relatives aux interventions d’entretien, fournies dans la présente notice, s’adressent exclusivement au personnel technique qualifié.
Mitteilung für CATV-Techniker Die in dieser Mitteilung aufgeführten Wartungsanweisungen sind ausschließlich für qualifiziertes Fachpersonal bestimmt. Um die Gefahr eines elektrischen Schlags zu reduzieren, sollten Sie keine Wartungsarbeiten durchführen, die nicht ausdrücklich in der Bedienungsanleitung aufgeführt sind, außer Sie sind zur Durchführung solcher Arbeiten qualifiziert.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
IMPORTANT SAFETY INSTRUCTIONS Protect the Product from Lightning In addition to disconnecting the AC power from the wall outlet, disconnect the signal inputs. Verify the Power Source from the On/Off Power Light When the on/off power light is not illuminated, the apparatus may still be connected to the power source. The light may go out when the apparatus is turned off, regardless of whether it is still plugged into an AC power source.
IMPORTANT SAFETY INSTRUCTIONS Protect from Exposure to Moisture and Foreign Objects WARNING: Avoid electric shock and fire hazard! Do not expose this product to dripping or splashing liquids, rain, or moisture. Objects filled with liquids, such as vases, should not be placed on this apparatus. WARNING: Avoid electric shock and fire hazard! Unplug this product before cleaning. Do not use a liquid cleaner or an aerosol cleaner.
United States FCC Compliance United States FCC Compliance This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against such interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
United States FCC Compliance RF Exposure Statements Note: This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. This equipment should be installed and operated with a minimum distance of 7.9 inches (20 cm) between the radiator and your body. For products available in the USA/Canada market, only channels 1-11 can be operated. The selection of other channels is not possible.
United States FCC Compliance National Restrictions This product is for indoor use only. USA/Canada This system has been evaluated for RS-210. When operating this system, adhere to the following requirements: OL-30 545 -01 When operating in the band 5150-5250 MHz, the device is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
United States FCC Compliance Ce système a été évalué pour les normes radioélectriques RS-210. Lorsque vous exploitez ce système, respectez les exigences listées ci-dessous. Quand l'appareil est exploité dans la bande 5150-5250 MHz, il peut uniquement être utilisé à l'intérieur pour réduire le risque de brouillage préjudiciable qui pourrait affecter les systèmes satellites portables sur la même voie.
United States FCC Compliance Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle frequenze in Italia. Se non viene installato all 'interno del proprio fondo, l'utilizzo di prodotti Wireless LAN richiede una “Autorizzazione Generale”. Consultare http://www.comuni cazi oni.it/i t/ per maggiori dettagli. Latvia The outdoor usage of the 2.4 GHz band requires an authorization from the Electronic Communications Office.
1 Chapter 1 Introducing the DOCSIS Wireless Residential Gateway Purpose This guide covers the following product models: DPC3829 DOCSIS Wireless Residential Gateway DPC3829M DOCSIS Wireless Residential Gateway All features described in this guide are standard to these models of residential gateways unless otherwise noted. For the purpose of this guide, whenever a feature or option applies to only a specific model, the model number is specified.
Chapter 1 Introducing the DOC SIS Wireless Residential Gateway Introduction Your Wireless Residential Gateway meets industry standards for high-speed data connectivity. This residential gateway delivers data and wired (Ethernet) or wireless gateway capabilities to connect a variety of devices in the home or small office and support high-speed data access and cost-effective voice services, all in one device.
What's In the Carton? What's In the Carton? When you receive your residential gateway, you should check the equipment and accessories to verify that each item is in the carton and that each item is undamaged. The carton contains the following items: One DPC3829 or DPC3829M DOCSIS Wireless Residential Gateway One power adapter (models requiring external power supply) One Ethernet cable (May not be provided with all products.) One USB cable (Image may vary from actual product.
Chapter 1 Introducing the DOC SIS Wireless Residential Gateway Front Panel Description The front panel of your residential gateway provides LED status indicators that indicate how well and at what state your residential gateway is operating. See Operation of Front Panel Indicators (on page 17), for more information on front panel LED status indicator functions. 4 1 POWER—ON, power is applied to the residential gateway. 2 DS—ON, the residential gateway is receiving data from the cable network.
Front Panel Description 8 OL-30 545 -01 WIRELESS SETUP—Press this button to activate the Wireless Setup feature. This feature allows users to add new Wireless Protected Setup (WPS) compliant wireless clients to the home network. When the SETUP indicator is OFF (normal condition), it indicates that the wireless setup is not active. BLINKING indicates the user has activated wireless setup to add new wireless clients on the wireless network.
Chapter 1 Introducing the DOC SIS Wireless Residential Gateway Back Panel Description The following illustration identifies the back panel components on the DPC3829 residential gateways. Descriptions for each component follow the illustration. Important: Do not connect your PC to both the Ethernet and USB ports at the same time. Your residential gateway will not function properly if both the Ethernet and USB ports are connected to your PC at the same time.
Back Panel Description CAUTION: The RESET button is for maintenance purposes only. Do not use unless instructed to do so by your service provider. Doing so may cause you to lose any settings you have selected.
2 Chapter 2 Installing the DOCSIS Wireless Residential Gateway Introduction This chapter describes how to properly install the residential gateway and to connect the residential gateway to a computer and other devices. In This Chapter OL-30 545 -01 Installation P reparations ....................................................................10 Install the Wireless Res idential Gateway .........................................
Chapter 2 Installing the D OC SIS Wireless Residential Gateway Installation Preparations Before installing the residential gateway, make sure that your system meets or exceeds the requirements listed in this section. Also, make sure that you have prepared your home and home devices as described in this section.
Installation Preparations Information Your Serv ice Prov ider Needs You will need to give your service provider the following information, which is printed on the bar code label attached to the device: The Serial Number (S/N) of the residential gateway. The serial number consists of a series of nine digits. The Media Access Control (CM MAC) address of the residential gateway. The CM MAC address consists of a series of 12 alphanumeric characters.
Chapter 2 Installing the D OC SIS Wireless Residential Gateway gateway for high-speed Internet service. Choose a location that is near an existing RF coaxial connection to eliminate the need for an additional RF coaxial outlet. Choose a location that is relatively protected from accidental disturbance or harm, such as a closet, basement, or other protected area. Choose a location so that there is plenty of room to guide the cables away from the residential gateway without straining or crimping them.
Installation Preparations Location and Dimensions of the Wall-Mounting Slots The following illustration shows the location and dimensions of the wall-mounting slots on the bottom of the residential gateway. Use this illustration as a guide for mounting the residential gateway to the wall. Note: Image not to scale. Mounting the Residential Gateway on a Wall 1 Using a drill with a 3/16-inch bit, drill two holes at the same height and 4 inches apart.
Chapter 2 Installing the D OC SIS Wireless Residential Gateway 3 Install the mounting screws into the wall; leave a gap of about 1/4-inch between the screw head and the wall. Then, go to step 4. 4 Verify that no cables or wires are connected to the residential gateway. 5 Lift the residential gateway into position.
Install the Wireless Residential Gateway Install the Wireless Residential Gateway This section describes how to connect your residential gateway to support the services that the residential gateway offers. Connect the Wireless Residential Gateway The following installation procedure ensures proper setup and configuration for the residential gateway.
Chapter 2 Installing the D OC SIS Wireless Residential Gateway More information about the factory default configuration of your wireless residential gateway can be found later in this guide in Configure Wireless Settings. 5 Locate the AC power cord provided with your residential gateway. Insert one end of the power cord into the AC connector on the back of the residential gateway. Then, plug the AC power cord into an AC outlet to power-up the residential gateway.
3 Chapter 3 Operation of Front Panel Indicators Introduction This section describes the behavior of the front panel indicators when the residential gateway is first powered up, during normal operations, and in special conditions. In This Chapter OL-30 545 -01 Initial Power Up, Calibration, and Registration (AC Power Applied) ..............................................................................................18 Normal Op erations (AC Power Applied) ........................................
Chapter 3 Operation of Front Panel Indicators Initial Power Up, Calibration, and Registration (AC Power Applied) The following chart illustrates the sequence of steps and the corresponding appearance of the residential gateway front panel LED status indicators during power up, calibration, and registration on the network when AC power is applied to the residential gateway. Use this chart to troubleshoot the power up, calibration, and registration process of your residential gateway.
Initial Power Up, Calibration, and Registration (AC Power Applied) OL-30 545-01 6 USB On or Blinking 7 WIRELESS ON/OFF On or Blinking 8 WIRELESS SETUP Off 18
Chapter 3 Operation of Front Panel Indicators Normal Operations (AC Power Applied) The following chart illustrates the appearance of the residential gateway front panel LED status indicators during normal operations when AC power is applied to the gateway.
Special Conditions Special Conditions The following chart describes the appearance of the residential gateway front panel LED status indicators during special conditions to show when you have been denied network access.
4 Chapter 4 Troubleshooting the DOCSIS Wireless Residential Gateway Introduction This chapter describes the most common issues that may occur after the residential gateway is installed and provides possible solutions and tips for improved performance of the residential gateway. In This Chapter OL-30 545 -01 Frequently Asked Questions .............................................................24 Common Troubles hooting Issues .....................................................
Chapter 4 Troubleshooting the D OCSIS Wireless Residential Gateway Frequently Asked Questions This section provides answers to common questions about the residential gateway. How Do I Configure TCP/IP Protocol? To configure TCP/IP protocol, you need to have an Ethernet Network Interface Card (NIC) with TCP/IP communications protocol installed on your system. TCP/IP is a communications protocol used to access the Internet.
Frequently Asked Questions 9 To get a DNS server address automatically using DHCP, click Obtain DNS server address automatically, and then click OK. To specify a DNS server address, click Use the following DNS server addresses, and then, in the Preferred DNS server and Alternate DNS server boxes, type the addresses of the primary and secondary DNS servers. To change advanced DNS, WINS, and IP settings, click Advanced. 10 When you are finished, click OK. 11 Try to access the Internet.
Chapter 4 Troubleshooting the D OCSIS Wireless Residential Gateway Note: Make sure that the Load only when needed option is unchecked. 6 Verify that the Use 802.3 option located in the upper-right corner of the TCP/IP window is unchecked. If there is a check mark in the option, uncheck the option, and then click Info in the lower-left corner. 7 Is there a Hardware Address listed in this window? If yes, click OK.
Frequently Asked Questions Renew ing the IP Address on Macintosh Sy stems 1 Close all open programs. 2 Open your Preferences folder. 3 Drag the tcp/ip preferences file to the Trash. 4 Close all open windows and empty the Trash. 5 Restart your computer. 6 As your computer starts, simultaneously press and hold down the Command (Apple), Option, P, and R keys on your keyboard.
Chapter 4 Troubleshooting the D OCSIS Wireless Residential Gateway How Do I Arrange for Installation? Call your service provider to inquire about professional installation. A professional installation ensures proper cable connection to the residential gateway and to your PC, and it ensures the proper configuration of all hardware and software settings. Contact your service provider for more information about installation.
Common Troubleshooting Issues Common Troubleshooting Issues This section describes common problems and offers solutions. I don't understand the front panel status indicators See Operation of Front Panel Indicators (on page 17), for more detailed information on front panel LED status indicator operation and function.
Chapter 4 Troubleshooting the D OCSIS Wireless Residential Gateway Tips for Improved Performance If your residential gateway does not perform as expected, the following tips may help. If you need further assistance, contact your service provider. Verify that the plug to your residential gateway AC power is properly inserted into an electrical outlet. Verify that your residential gateway AC power cord is not plugged into an electrical outlet that is controlled by a wall switch.
5 Chapter 5 Customer Information Introduction If you have technical questions, call Cisco Services for assistance. Follow the menu options to speak with a service engineer. Access your company's extranet site to view or order additional technical publications. For accessing instructions, contact the representative who handles your account. Check your extranet site often as the information is updated frequently.
Index power switch • 6 product • 2 A accessing the Internet • 28 accessories • 3 P C performance, tips to improve • 30 product accessories • 3 features • 2 overview • 2 cable service • 27 connections description of • 6 to computer • 28 E S Ethernet • 29 exposure to moisture • viii safety instructions • vii ground product • viii system requirements • 10 F T features, product • 3 T CP/IP configuring for Macintosh systems • 25 configuring for Windows XP • 25 troubleshooting • 23 I indicators beha
Americas Headquarters http://www.cisco.com Cisco Systems, Inc. Tel: +1-408 526-4000 170 West Tasman Drive +1-800 553-6387 San Jose, CA 95134-1706 Fax: +1-408 527-0883 USA This document includes various trademarks of Cisco Systems, Inc. Please see the Notices section of this document for a list of the Cisco Systems, Inc. trademarks used in this document. Product and service availability are subject to change without notice. © 2013 Cisco and/or its affiliates. All rights reserved.
