User's Manual
WARNING: Avoid electric shock and re hazard! Unplug
this product before cleaning. Do not use a liquid cleaner or an
aerosol cleaner. Do not use a magnetic/static cleaning device
(dust remover) to clean this product.
WARNING: Avoid electric shock and re hazard! Never
push objects through the openings in this product. Foreign
objects can cause electrical shorts that can result in electric
shock or re.
Service Warnings
WARNING: Avoid electric shock! Do not open the
cover of this product. Opening or removing the cover may
expose you to dangerous voltages. If you open the cover,
your warranty will be void. This product contains no user-
serviceable parts.
Check Product Safety
Upon completion of any service or repairs to this product, the service
technician must perform safety checks to determine that this product
is in proper operating condition.
Protect the Product When Moving It
Always disconnect the power source when moving the apparatus or
connecting or disconnecting cables.
Compliance Information
United States FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against such interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy. If not installed and used in accordance
with the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment OFF and ON, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit di erent from that
to which the receiver is connected.
• Consult the service provider or an experienced radio/television
technician for help.
Any changes or modifications not expressly approved by Cisco
Systems, Inc., could void the user’s authority to operate the equipment.
The information shown in the FCC Declaration of Conformity paragraph
below is a requirement of the FCC and is intended to supply you with
information regarding the FCC approval of this device. The phone
numbers listed are for FCC-related questions only and not intended
for questions regarding the connection or operation for this device.
Please contact your service provider for any questions you may have
regarding the operation or installation of this device.
IMPORTANT NOTE: FCC RF Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
CXD01ANI XiD-C Set-Top
Model: CXD01ANI
Manufactured by: Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134 USA
www.cisco.com/go/contacts
Canada EMI Regulation
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class B est conforme à la norme NMB-
003 du Canada.
AVC VIDEO LICENSE
With respect to each AVC/H.264 product, we are obligated to provide
the following notice:
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO
LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER
USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i)
ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC
VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY
A CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS
OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC
VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY
OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM
MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM.
Accordingly, please be advised that service providers, content providers,
and broadcasters may be required to obtain a separate use license from
MPEG LA prior to any use of AVC/H.264 encoders and/or decoders.
ROVI CORPORATION COPYRIGHT NOTICE
This product incorporates copyright protection technology that is
protected by U.S. patents and other intellectual property rights of
Rovi Corporation. Use of this copyright protection technology must
be authorized by Rovi Corporation, and is intended for home and
other limited viewing uses only unless otherwise authorized by Rovi
Corporation. Reverse engineering and disassembly are prohibited.
Disclaimer
Cisco Systems, Inc. assumes no responsibility for errors or omissions that
may appear in this manual. We reserve the right to change this manual
at any time without notice.
Open Source GNU GPL Statement
Cisco Model CXD01ANI XiD-C set-top(s) may contain, in part, certain
free and/or open source software (“Open Source”) under separate
license terms. Examples of such licenses may include all versions of
the GNU General Public License (GPL), GNU Lesser General Public
License (LGPL), BSD license, MIT license, Mozilla Public License,
Eclipse Public License, Apache license, and others. To nd specic
information regarding the Open Source in your product, including copies
of the applicable license documentation and related information, go to:
(i) for North America http://www.cisco.com/web/consumer/support/
open_source.html, or (ii) for outside North America http://www.cisco.
com/web/consumer/support/open_source.html#international. Once
at the site, search for the product listing and click the related items
identied. If you have any questions or problems accessing any of
the links, contact: spvtg-external-opensource-requests@cisco.com.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its aliates in the U.S. and other countries. To view a list of Cisco’s trademarks, go
to this URL: www.cisco.com/go/trademarks.Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company. (1110R)
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Denition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
© 2015 Cisco and/or its aliates. All rights reserved. Last Updated: June 2015 Part Number 78-100744-01A0
Printed in China