® AUX2000 Auxiliary Control Box Installation/ Operation Manual C916M (11/90) Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USAwww.pelco.
TABLE OF CONTENTS Section Page 1.0 WARNINGS ........................................................................................................................................ 1 2.0 SCOPE ...............................................................................................................................................2 3.0 DESCRIPTION ................................................................................................................................... 2 3.
INSTALLATION/OPERATION MANUAL AUX2000 AUXILIARY CONTROL BOX FOR THE COAXITRON® AND WIRETRON RECEIVER/DRIVER 1.0 WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 4. Only use replacement parts recommended by Pelco. 1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes. 5. 2.
2.0 SCOPE 3.2 RECOMMENDED CONTROLS The information contained within this manual covers the installation and operation of the AUX2000. CX9024RX 3.0 DESCRIPTION The AUX2000 is an auxiliary control box for the Coaxitron® and Wiretron receiver/drivers. It enables the logic level AUX 1-3 signals from the Coaxitron® and Wiretron receiver/drivers to control devices such as motors for motor operated gates, lights for parking areas, or power relays for high power requirements.
4.0 INSTALLATION Refer to the following instructions when installing the AUX2000 auxiliary control box for the Coaxitron® and Wiretron receiver/drivers. 1. Determine the location for the AUX2000 auxiliary control box for the Coaxitron® or Wiretron receiver/ drivers. To determine the mounting location, consider the distance between the AUX2000 auxiliary control box for the Coaxitron® and Wiretron receiver/ drivers and auxiliary functions used.
4.1 MATING CONNECTOR ASSEMBLY Installation and/or testing will require you to assemble the connector parts provided. Fabricate the interconnecting cable according to the following steps (reference Figure 2). 1. 2. 3. 4. The contact pins supplied with the mating connector are the “crimp” type which may also be soldered if you so desired (item 4). 5. After crimping or soldering the contact pins to the conductors, push them into the proper holes in the connector until they snap in place.
5.0 OPERATION The AUX2000 is operated by the Coaxitron ® or Wiretron controller. 5.1 SYSTEM TEST Using the systems controller, verify that the auxiliary devices function. 6.0 TROUBLESHOOTING GUIDELINES In the event that the auxiliary equipment do not work, retrace the wiring and verify correctness and check the fuse to make sure it did not open. Correct all errors in wiring and replace the fuse if opened. Retry to operate the auxiliary equipment.
7.0 AUX2000 MECHANICAL PARTS LIST Description Part Number Enclosure Fuse holder Terminal Strip Strain Relief Mating Connector (Sockets) Mating Connector (Pins) DS100JA4000COMP FUS357001 TRS20007 EH5510043 CONA37S CONA37P 8.0 ELECTRICAL PARTS LIST Schematic ID CON1 CON2-CON3 CON4-CON5 CON6 F1 L1-L3 Plug 1 RY1-RY3 6 Description Connector, 37 pins Connector, 6 position Connector, 2 position Connector, 37 sockets Fuse, 3 AMP, 3AG Choke, 6.
1 2 3 5 6 7 8 9 10 11 12 13 14 36 30 34 33 P/T COMMON MANUAL IRIS LEFT DOWN UP RIGHT GROUND CAMERA AC (HIGH) IRIS FOCUS ZOOM LENS COMMON CAMERA AC (LOW) COMMON AUX 1 AUX 2 AUX 3 CON1 Pelco Manual C916M (11/90) 4 1 6 2 PCB1500522 CON2 3 4 3 4 3 4 2 1 2 1 2 1 RY3 RY2 RY1 FEED THROUGH CON3 2 1 2 1 2 4 3 F1 CON5 CON4 L3 L2 L1 18 19 17 16 15 1 2 3 5 6 7 8 9 10 11 12 13 14 AC HI AC NEUTRAL AUX 3 AUX 2 AUX 1 PLUG 1 P/T COMMON MANUAL IRIS LEFT DOWN UP RIGHT GROUND
.0 SPECIFICATIONS MECHANICAL Enclosure: UL listed gray industrial control panel enclosure Weatherproofing: Cover and connectors fully gasketed Mounting Means: 6 - 0.31" (.79 cm) diameter holes Dimensions: 11.31" H x 9.44" W x 4.32" D (28.7 cm x 4.25 cm x 10.97 cm) Unit Weight: 7 lbs (3.15 kg) Shipping Weight: 9 lbs (36.
NOTES Pelco Manual C916M (11/90) 9
11.0 WARRANTY AND RETURN INFORMATION WARRANTY RETURNS Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex® Series products (multiplexers, server, and keyboard).
