ADDENDUM Addendum No. C1573M Date February 1, 2006 Manuals Affected C1572M, C1555M-F, C1566M-C Manual Update The front and rear mounting rails and the mounting brackets are no longer supplied with the CM9700-CC1. Disregard the CM9700-CC1 mounting information in the above referenced manuals. To mount the CM9700-CC1 into a standard 19-inch EIA rack follow these instructions: 1. Insert the CM9700-CC1 into the rack. 2. Tighten the CM9700-CC1 to the rack using the four supplied Phillips screws with washers.
INSTALLATION/OPERATION System 9780 ® C1566M-C (10/05)
Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 List of Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 List of Tables . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . .
List of Illustrations 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 4 CM9780-MXB Mounting Baffle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Mounting the CM9780-MXB on Top of the Mounting Baffle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
List of Tables A B C D E F G H I J K L M N O LEDs Illuminated During a Basic Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Data Connections—Single Node Systems Without a Hot Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Data Connections—Networked System Without a Hot Switch . . . . . . . . . . . . . . . . . . . . . . .
Description The System 9780 is a full-featured video matrix switching control system that allows you to view and control up to 4,096 cameras and 512 monitors on a single node. Video patch panels (CM9700-VPP) allow you to connect up to 512 cameras on each CM9780-MXB bay compared to 256 cameras on the System 9770. The System 9780 has the following basic components: • CM9700-CC1—This is the system CPU; connect matrix bays, keyboards, PTZ camera control lines, and peripheral devices to the CC1.
Network Interface Unit CM9700-NW1 Network interface unit; network CPU and software necessary for joining two or more independent systems together. Keyboards The following keyboards are compatible with the System 9780: CM9760-KBD Full-function desktop variable-speed keyboard; 120 VAC, 60 Hz. CM9760-KBD-X Same as CM9760-KBD except 230 VAC, 50 Hz. CM9760-KBR Full-function 19-inch EIA rack mount keyboard; 120 VAC, 60 Hz. CM9760-KBR-X Same as CM9760-KBR except 230 VAC, 50 Hz.
Installation UNPACKING 1. Unpack and inspect all equipment, and verify delivery according to the packing slip. Before shipping, Pelco connects, tests, and programs each system according to the individual sales order. Contact Pelco immediately if there is any discrepancy in the equipment that you receive.
MOUNTING Install the System 9780 in EIA-standard, 19-inch (48.26 cm) racks. CM9780-MXB 1. Install the CM9780-MXB mounting baffle first (refer to Figure 1). The mounting baffle uses 1 rack unit (RU), and it has front and rear mounting ears, which are attached to the front and rear mounting rails. The rear mounting brackets are adjustable to allow for different depths of cabinets. NOTE: Be sure to use all eight screws provided with the mounting baffle.
Figure 2. Mounting the CM9780-MXB on Top of the Mounting Baffle 3. (Optional) Install additional CM9780-MXB mounting trays and matrix bays to the side of and below the first unit, as necessary. WARNING: Always install equipment starting from the bottom of the rack frame or cabinet. Installing equipment from the top down will make a rack or cabinet top heavy and could cause the equipment to tip over. NOTE: Each CM9780-MXB has a unique label for identifying the bay location in the installation.
3. Attach one set of support rails to the equipment rack in the desired location as follows: a. Position the ear of the front-mounting support rail against the front of the equipment rack and align the holes in the ear of the rail with the threaded holes in the rack. Attach the ear of the rail to the rack using two 10-32 x 0.375-inch flat head screws. b. Adjust the support rails to the correct depth of the equipment rack by sliding the rear-mounting support rail to the back of the equipment rack. c.
CM9700-VPP There are two ways you can mount a CM9700-VPP video patch panel into a rack. 1. Single panels into a rack 2. Up to 16 panels using the CM9700-VPP-RK The following illustration shows how to mount a single panel into a rack. The panel is mounted horizontally. You can mount multiple panels horizontally. This takes up more rack space than if using the CM9700-VPP-RK. RACK CABLE BRACKET CM9700-VPP (4) SCREWS, 10-32X3, PHILLIPS PANHEAD WITH WASHERS RACK MOUNT BRACKET Figure 4.
VIDEO INPUT/OUTPUT CONNECTIONS The following steps provide an overview of how to connect video input and output sources. More complete procedures are provided in the subsequent sections. NOTE: If your System 9780 is configured by Pelco, the appropriate number of video input cards and monitor output cards and BNC and DFC rear panels are installed at the factory, and steps 1 and 2 are not necessary. If this is the case, skip to Step 3. 1. Install the CM9780-VCC and CM9780-VMC cards in the matrix bay.
INSTALLING VIDEO INPUT CARDS (CM9780-VCC) Video input cards are inserted into every slot, starting with slot 1 (refer to Figure 6). To add a video card, slide the card into the first slot. Continue as necessary, using every slot, up to a maximum capacity of sixteen video input cards. HOT SWAPPING: You can “hot swap” a video input card—remove a card and/or insert a new card—while the system is powered and running.
INSTALLING MONITOR OUTPUT CARDS (CM9780-VMC) The monitor output card located in slot 18 is the primary card, and it handles video for monitors 1-16. Refer to Figure 7. Note that the CM9780-MXB will not function without a CM9780-VMC card inserted into slot 18. An optional secondary VMC card can be installed in slot 17. This card routes video for monitors 17-32. HOT SWAPPING: You can “hot swap” a monitor output card—remove a card and/or insert a new card— while the system is powered and running.
PERFORMING A BASIC LED CHECK You should perform a basic LED check before you connect any video input or output to the matrix bay. The LED check allows you to make sure that the system is operating properly. 1. Turn on the power switch on the rear of the matrix bay. The front cover can either be open or closed during the LED check. 2. Various LEDs will blink during the initialization process as the software verifies communication and version level information.
INSTALLING REAR PANEL CARDS The following rear panel cards can be used with the CM9780-MXB matrix bay: • CM9780-DFC—This card is used to connect video ribbon cables from the CM9700-VPP video patch panels (this card can also be used for sideframing, downframing, and looping video; refer to the Looping Video section and to the Sideframing and Downframing sections in the Appendix for more information). • CM9780-RPM—This is the BNC card for monitor connections.
When looping video out to another device (such as a DVR, VCR, or switcher), set the termination jumpers on the CM9780-DFC cards to the unterminated position. INPUT FROM CM9700-VPP PATCH PANEL – CONNECTOR A TERMINATED UNTERMINATED JP16 JP15 JP14 JP13 JP12 JP11 32 1 JP10 JP9 JP8 JP7 JP6 JP5 JP4 JP3 JP2 JP1 UNTERMINATED TERMINATED INPUT FROM CM9700-VPP PATCH PANEL – CONNECTOR B JP32 JP31 JP30 JP29 JP28 JP27 JP26 JP25 JP24 JP23 JP22 JP21 JP20 JP19 JP18 JP17 Figure 9.
3. Tighten the screws at the top and bottom of the BNC card. PRIMARY VMC CARD (SLOT 18) OPTIONAL: SECONDARY VMC CARD (SLOT 17) 2 CM9780-RPM BNC PANELS (SECOND PANEL OPTIONAL) Figure 10.
LOOPING VIDEO Use the CM9700-VPP panels to loop video from the CM9780-MXB out to another device (such as a DVR, VCR, or switcher), as shown in Figure 11. When looping video, set the termination jumpers on the CM9780-DFC cards to the unterminated position. Terminate the video signal at the final device. CAMERA CM9700-VPP PORT A CAMERA PORTB CM9700-VPP PORT A PORTB CM9780-MXB CM9700-VPP PORT A PORTB CM9700-VPP PORT A PORTB DVR DVR Figure 11.
VIDEO INPUT/OUTPUT CAPACITY Single Bay A single CM9780-MXB can support up to 512 camera inputs (in increments of 32) and 32 monitor outputs (in increments of 16). Refer to Figure 12. CM9700-CC1 PRINTER COM 1 COM 2 CM9780-MXB CAMERA 17 MONITOR 1 VIDEO RIBBON CABLE MONITOR 32 PORT B CM9700-VPP VIDEO RIBBON CABLE CM9700-VPP-RK PORT B PORT B PORT A CAMERA 512 Figure 12.
Multiple Bays, Single Node In a single-node system with one CM9700-CC1 (not networked), you can connect multiple CM9780-MXBs using “sideframing” and “downframing” for a maximum capacity of 4,096 camera inputs and 256 monitor outputs. NOTE: When using CM9760-MDA units, you can increase the monitor output capacity to a maximum of 512. Refer to the Downframing section in the Appendix for more information on using CM9760-MDA units.
CAMERA 1025 CM9700-VPP PORT A PORT B CM9700-VPP PORT A CM9700-VPP PORT B PORT A CM9700-VPP PORT B PORT A CAMERA 1536 PORT B CAMERA 1024 CAMERA 512 CAMERA 1 CAMERA 513 PORT B PORT A CM9700-VPP CM9700-VPP PORT A MONITOR 1 PORT A PORT B PORT B MONITOR 32 PRINTER TO CM9700-CC1 COM 1 COM 2 TO CM9700-CC1 OUTPUT BAY OPTIONAL: ADD CM9780-VCC VIDEO CARDS AND DFC INPUT CARDS TO CONNECT ADDITIONAL VIDEO INPUTS (THROUGH VPP PANELS) DIRECTLY TO THE OUTPUT BAY CM9780-MXB CM9780-MXB CM9780
PORT B PORT A CM9700-VPP CM9700-VPP PORT A PORT A PORT B PORT B CAMERA 1536 CAMERA 1024 CAMERA 1025 CAMERA 513 CM9700-VPP MONITOR 1 PORT A MONITOR 32 CM9700-CC1 CM9700-VPP PORT B PORT A PORT B PRINTER COM 1 COM 2 SIDEFRAME CABLES CM9780-MXB OUTPUT BAY CM9780-MXB CM9780-MXB OPTIONAL: ADD CM9780-VCC VIDEO CARDS AND CM9780-RPC BNC CARDS TO CONNECT SIDEFRAME CABLES FROM ADDITIONAL BAYS, OR TO CONNECT CAMERAS DIRECTLY TO THE OUTPUT BAY (WHEN USING SEVEN MATRIX BAYS OR FEWER) TO CM9700-C
Refer to the Downframing section in the Appendix for detailed downframing instructions. CM9700-CC1 CAMERA 480 PRINTER COM 1 COM 2 CM9700-VPP PORT A PORT B CAMERA 512 MONITOR 1 VIDEO RIBBON CABLES CM9780-MXB CAMERA 1 CM9700-VPP PORT A PORT B CAMERA 32 VIDEO RIBBON CABLES MONITOR 32 DOWNFRAME CABLES CM9780-MXB MONITOR 33 MONITOR 64 Figure 16.
Networked System A networked system with multiple nodes uses an NIU (network interface unit) to combine up to 24 CM9700-CC1 systems into a network—each CC1 system is called a “node.” Multiple CM9780-MXB units can be connected to each CC1 through sideframing and downframing. An NIU is a CM9700-CC1 loaded with networking software, sold as a CM9700-NW1. Refer to Figure 17. CM9700-CC1 NW1 CM9700-CC1 NODE 5 CM9700-CC1 NODE 7 CM9700-CC1 NODE 6 CM9780-MXB CM9780-MXB CM9780-MXB Figure 17.
THE POWER SUPPLY MODULE (CM9700-MPS) You can add a backup power supply module (CM9700-MPS) to a System 9780 matrix bay to provide redundancy to the bay’s power supply. NOTE: You can “hot swap” a backup power supply module—remove and/or insert a backup power supply—while the system is powered and running. INSTALL A BACKUP POWER SUPPLY 1. Open the matrix bay front cover. 2. Remove the blank-off plate from the empty power input slot. 3. Slide the power input module partially into the bay, on the guide rail.
HOW TO REPLACE THE FUSE IN A POWER SUPPLY MODULE The matrix bay is shipped from the factory configured for the correct input power. The power input panel, on the rear panel of the matrix bay, provides two separate power input receptacles, one for each power supply. NOTE: The power input panel is not serviceable and should be removed or installed only by Pelco. Each power input receptacle is equipped with a fuse assembly. In addition, each fuse assembly also provides a spare fuse. Refer to Figure 19.
HOW TO TURN OFF THE AUDIBLE POWER SUPPLY ALARM The power supply module contains an audible alarm, which operates in conjunction with the fault LEDs located on the power supply front panel. To turn off this alarm, complete the following steps: 1. Turn off the matrix bay power. 2. Remove the power supply module from the matrix bay frame. 3. Move the speaker switch to the OFF position (refer to Figure 20). 4. Insert the power supply module back into the matrix bay frame. 5. Turn on the power.
SYSTEM DEVICE CONNECTIONS 1. Turn off the power to all system devices and disconnect all power line cords while connecting system devices. 2. Complete the following steps to connect one or more CM9760-KBD system keyboards. NOTE: CM9760-KBD software version 8.03 or higher is required. a. Connect the keyboard to the CM9505-UPS using the straight cable supplied with the keyboard. b. Connect the CM9505-UPS to one of the RS-422 COM ports on the CC1 using the 6-foot (1.
CM9700-MGR VGA MONITOR CM9700-CC1 PS/2 KEYBOARD Figure 22. CM9700-CC1 Device Connections CM9700-MGR PC COM PORT RS-232 CABLE CM9700-CC1 COM 1/COM 2 PIN 3 (TX) PIN 2 (RX) PIN 2 (RX) PIN 3 (TX) PIN 5 (GND) PIN 5 (GND) DB9 FEMALE DB9 FEMALE CM9700-MGR PC COM PORT CM9700-CC1 COM 1/COM 2 RS-232 CABLE PIN 2 (TX) PIN 2 (RX) PIN 3 (RX) PIN 3 (TX) PIN 7 (GND) PIN 5 (GND) DB25 FEMALE DB9 FEMALE Figure 23. CM9700-MGR PC Pin-Out Detail 6. Install any additional system peripheral devices.
RS-422 COM PORT (“SERCOM”) CONNECTIONS All peripheral equipment in a System 9780 connect through the RS-422 COM ports on the CM9700-CC1 rear panel. (These ports are also known as “sercom” ports, short for “serial communication” ports.) If you exceed the number of CM9700-CC1 rear panel ports available, you can add ports with the CM9700/9760-SER port expander unit.
Table D. Data Connections—Single Node, Hot-Switched System MXB connection(s) CC1 port 6 and next consecutive ports, as necessary—connected through the hot switch. Hot Switch connection CC1 port 5. Other peripherals Any available port— connected through the hot switch. These connections do not have to be in sequential ports. Table E. Data Connections—Networked, Hot-Switched System MXB connection(s) CC1 port(s) 7 and next consecutive ports, as necessary—connected through the hot switch.
CM9700-CC1 REVERSED CABLE PIN 1 CM9780-MXB PIN 8 CM9780-MXB RJ-45 PIN-OUTS PIN 1 = TX+ PIN 2 = TXPIN 7 = RXPIN 8 = RX+ REVERSED DATA CABLE CM9700-CC1 RJ-45 PIN-OUTS PIN 1 = TX+ PIN 2 = TXPIN 7 = RXPIN 8 = RX+ Figure 24. Sample CM9780-MXB to CM9700-CC1 Connection CM9700-NW1 CM9700-CC1 NODE 5 CM9700-CC1 NODE 7 CM9700-CC1 NODE 6 CM9780-MXB CM9780-MXB CM9780-MXB Figure 25.
System Start-Up To start up your system you must complete the following tasks: 1. Install the CM9700-MGR on a PC connected to the CC1. Refer to System Device Connections in the Installation section for instructions on connecting a PC to the CC1. Refer to the CM9700-MGR Software Guide for instructions on installing the CM9700-MGR software. 2. Complete the following steps on the CM9700-MGR PC (instructions are provided in the CM9700-MGR Software Guide): a. Copy the CM9700 system design file (the *.
VERIFY SYSTEM OPERATION 1. Power up all the remaining equipment. 2. After the CM9700-CC1 loads the configuration files, “SYSTEM 97XX” appears on the CM9760-KBD LCD. 3. Enter the default operator password on the CM9760-KBD keypad. “ENTER MONITOR #” appears on the LCD. NOTE: The default password for operator 1 is 0101; operator 2 is 0202; operator 3 is 0303; and so on. These numbers are defined in the Operator PIN field in CM9700-MGR. 4. Enter 1, and then press the MON key.
MONITOR COLOR ADJUSTMENT Once you have connected all devices and powered the system, you can use the System 9780 color bars as a reference tool for adjusting the color on each monitor. 1. Enter the monitor number, and then press the MON key. 2. Enter 999998, and then press the CAM key. Broadcast quality color bars appear on the monitor. BLACK BLUE RED MAGENTA (LIGHT PURPLE) GREEN CYAN (LIGHT BLUE) YELLOW WHITE 3.
Programming Your System When you open CM9700-MGR, the Getting Started dialog box appears. Figure 28. Getting Started Dialog Box The CM9700-MGR provides the following configuration options: • Setup Wizard: This option opens the Setup Wizard (a series of dialog boxes), which provides assistance in setting up a new system. • New System: This option opens the CM9700-MGR main window with a blank system. Use this option when you want to create a new system configuration from scratch.
GETTING HELP USING CM9700-MGR Instructions for how to use CM9700-MGR are provided throughout the software. The CM9700-MGR provides wizards to help users complete tasks, such as adding a device or a group. Each wizard screen contains instructions and explanatory text. Figure 29. Sample Wizard Page When you are working within the table view or tree view (refer to Figure 30) on the CM9700-MGR main window, help is provided as “real-time” help.
Operation A brief description of System 9780 operation is provided here. Power-up the system. Refer to the System Start-Up section. Switch monitor. Enter the monitor number. Press the MON key. Select camera. Enter the camera number. Press the CAM key. Control PTZ receivers. Use the appropriate PTZ control keys or joystick (depending on the keyboard used). Call a preset. Program the preset through the keyboard. Enter the preset number.
Appendix SYSTEM ARCHITECTURE NOTE: The System 9780 is similar to Pelco’s System 9760 but uses different matrix bay hardware and provides more features. Users familiar with the System 9760 should note the following differences: • Each System 9780 video input card (CM9780-VCC) receives input from 32 video connections (from the CM9700-VPPs which contain 32 BNC connectors). A fully loaded CM9780-MXB matrix bay supports 512 video inputs with sixteen video input cards.
INSTALLING ADDITIONAL MATRIX BAYS When either more cameras and/or more monitors are needed than can be accommodated by one matrix bay (512 x 32), you can install additional matrix bays in either of the following configurations: • Sideframing—This option increases the number of available video inputs • Downframing—This option increases the number of monitors available for output Sideframing To expand the matrix video inputs beyond 512, you can use multiple bays, with video from the monitor outputs on eac
1 2 3 Figure 32. CM9780-RPC Termination Jumpers—Right Card 3 1 Figure 33. CM9780-RPC Termination Jumpers—Left Card NOTE: You will note that the video DFC card consists of two cards connected into one unit. Each video DFC card (CM9780-DFC) provides 32 video input connections and connects to one video input card (CM9780-VCC).
Downframing To expand the matrix video outputs beyond 32, you can loop the video from the first CM9780-MXB to subsequent CM9780-MXB units for an additional 32 monitor outputs on each matrix bay. You can also loop the video using CM9700-VPPs and DVRs. Refer to Figure 34 and Figure 35.
CM9780-MXB CM9780-MXB CM9780-MXB CM9700-VPP PORT A PORTB CM9700-VPP PORT A PORTB DVR DVR Figure 35.
Downframe Card When you are downframing video, each downframed bay must be populated with CM9780-DFC cards. Set the termination jumpers in the unterminated position in each bay that is not the final device. Terminate the video signal at the final point in the downframe configuration, which could be either of the following: • If you are not looping video out from the final bay, terminate the video in the final bay.
HOW TO INSTALL OR REPLACE A CM9700-SER CARD IN THE CC1 If you have ordered a replacement or additional CM9700-SER serial communication card, complete the following steps to configure the jumpers on the CC1 board for the slot position the new SER card will occupy. NOTE: When connecting peripheral equipment to the serial communication ports, shielded cabling is required to comply with CE emissions guidelines. 1. Turn off the CC1 power switch.
W1 IRQ SELECT IRQ 15 IRQ 14 IRQ 12 IRQ 10 IRQ 11 IRQ 7 IRQ 9 IRQ 5 IRQ 6 PIN 21 IRQ 4 PIN 22 PIN 1 IRQ 3 PIN 2 W2 ADDRESS SELECT PIN 2 PIN 4 PIN 1 PIN 3 Figure 39. SER Card Jumper Assignments 4. Insert the new SER card into an available ISA slot. The default CM9700-CC1 configuration provides SER cards in ISA slots 1 and 2, so you will most likely insert the new card into slot 3 or 4. Refer to Figure 40. 5. Replace the top cover of the CC1. 6. Power up the CC1.
VIDEO INPUT CARD (CM9780-VCC) DETAIL VSYNC OFF ON GREEN AMBER RED AMBER Figure 41. CM9780-VCC Card Table H. Video Input Card (CM9780-VCC) LEDs Front Panel Label Color When LED Is On + Green The +5 VDC power source is functioning properly. - Green The -5 VDC power source is functioning properly. HB Amber The CPU is active; this “heartbeat” LED blinks at a different rate, according to the current activity: 0.
MONITOR OUTPUT CARD (CM9780-VMC) DETAIL DIP SWITCH GREEN AMBER Figure 42. CM9780-VMC Card Table I. Monitor Output Card (CM9780-VMC) LEDs Front Panel Label 50 Color When LED is on or blinking + Green The +5 VDC power source is functioning properly. - Green The -5 VDC power source is functioning properly. HB Amber The CPU is active; this “heartbeat” LED blinks at a different rate, according to the current activity: Primary VMC—0.
The monitor output card DIP switch selects various options. These switches are set in the proper position at the factory, but they can be changed, if necessary. Table J.
NETWORKING Networking of systems is required when any of the following conditions apply: • Two or more individual systems need to share video and control features. The CM9700-NW1 network interface unit (NIU) allows you to link any combination of the following systems into a network: • One or more System 9740 or 9760 systems (note that the CM9740-CC1/CM9760-CC1 must be upgraded to software version level 9.02) • One or more System 9780 systems • More than 2,048 cameras are required.
CONNECTING SATELLITE DEVICES You can connect a CM6800E-48X8 matrix switcher or a CM6700-SAT device to the System 9780. Refer to the CM9760-SAT Installation/Operation manual or to the CM6800E-48X8 Installation/Operation manual for instructions. The procedure for using a satellite device with a CM9700-CC1 is the same as for a CM9760-CC1, except that the programming within CM9700-MGR is more user-friendly. You just need to add the satellite device using the Add Device wizard.
MOUNTING THE CM9780-MXB IN AN OPEN RACK Figure 46. Mounting the CM9780-MXB in an Open Rack DOS ENVIRONMENT AND COMMAND REFERENCE DOS stands for Disk Operating System. Every time you turn on the CM9700-CC1 or every time you reboot (Alt +Ctrl +Del), the computer loads DOS from the CC1 disk into the memory (RAM). Once loaded DOS lets you run other programs, in particular, the CM9700.EXE program. On factory-configured systems the autoexec.
4. If the “hidden” files are present, IO.SYS loads first and executes. An initialization program called SYSINIT contained within IO.SYS reads in the MSDOS.SYS file; SYSINIT next locates the CONFIG.SYS file and executes its files for it to configure itself in memory. Then, SYSINIT locates and invokes COMMAND.COM. If SYSINIT cannot find COMMAND.COM, DOS displays the “Bad or missing Command Interpreter“ error message. NOTE: Since COMMAND.
DOS Commands DOS commands are divided into two groups. Because of the large number of DOS commands available, only the most commonly used commands are loaded into memory (RAM). The remaining commands reside in the DOS directory. The commands loaded into memory are called internal commands and the commands in the DOS directory are called external commands. When DOS reads a command, it looks first in RAM, then it looks in the DOS directory, and then it looks in the directory from which the command was issued.
If you entered the same command again (CD..) at the c:\9700> prompt and pressed the ENTER key, you would finally end up again at the root directory as previously done. To proceed directly from the directory you are in to another directory, no matter where in the directory tree you are, enter the total directory path of the location you wish to go to at the system prompt. For example, to get to the C:\9700\BKUPTST directory from the root directory, type C:\> CD [directory path], and then press the ENTER key.
DOS REFERENCE The following table provides a list of the most common DOS commands that you are most likely to use when operating the CC1. In addition, you can use the command HELP to access the MS-DOS command reference on the CC1. NOTE: In DOS, the backslash symbol (\) used alone, refers to the root directory. The [..] symbol refers to the parent directory. Table K.
COMMAND EXAMPLE(S) FASTHELP C:\>FASTHELP Lists and briefly describes every command provided with MS-DOS. This list is much less detailed than the list you get using the HELP command. C:\>FASTHELP DIR Specifies the name of the command that you wish FASTHELP to give information about, in this example, DIR. C:\>FORMAT A: Formats a disk for use with MS-DOS. FORMAT C:\>FORMAT A:/S HELP SWITCHES /S COMMENTS Transfers system files to the formatted disk.
Troubleshooting Problems with the CC1 Problems with the CC1 as part of a 9780 system may occur in the following areas: • The CC1 itself • Setup files (also known as configuration files) • Peripheral devices connected to the CC1 • DOS operating system A log is recommended for keeping track of changes made to the system. The log should document the change made, why it was made, the date it was made and the person responsible for the change.
The VCC Card CF LED Is Illuminated and the AUX LED Is Blinking Problem: The LED labeled “CF” on the CM9780-VCC Video Input card is illuminated, and the LED labeled “AX” is flashing. Solution: Refer to Table N to interpret the flashing of the AX LED. Table N.
Specifications CM9700-CC1 ELECTRICAL Input Voltage 120 VAC, 60 Hz or 230 VAC, 50 Hz, autoranging Power Consumption 57 watts Processor Pentium® class CPU Clock Speed 733 MHz Memory 64 MB RAM Disk Drive 3.5-inch, 1.
CM9780-MXB ELECTRICAL Input Voltage 100-240 VAC, 50/60 Hz, autoranging Power Consumption 60 watts maximum (fully populated) Communication Full duplex RS-422 using an RJ-45 connector VIDEO Inputs Card slots support up to 512 inputs per bay Outputs Two output card slots for supporting 32 outputs per bay Video Input Level 0.5 to 2 Vp-p, RS-170 composite video Impedance 75 ohms terminating (looping versions available) Crosstalk–Adjacent Channel -61 dB at 3.
Regulatory Notices CM9780-MXB This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series products (multiplexers, server, and keyboard).
® Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.
