I N S T A L L A T I O N TW3001AR Active Receiver Single Channel for UTP Transmission C1666M-A (4/06)
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules.
Description The TW3001AR is a single-channel active receiver that can receive live video over unshielded twisted pair (UTP) cable. The adaptive technology in the TW3001AR automatically adjusts the low, medium and high frequency components of the video signal allowing for the best possible video transmission. The adaptive technology eliminates the need for manual adjustment by automatically adjusting to provide the most favorable video transmission depending on cable length needed.
PARTS OF THE RECEIVER MODEL SN FREQ 4 5 AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUSING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, 3 2 1 + - W Figure 1. TW3001AR Parts 6 Rubber Feet (4): For placing unit on a flat surface, such as a desk or shelf.
Installation Make sure all parts are present for the unit. 1 1 1 1 Universal power supply (Part #PS04-1502-0512G) Wall clip 2-pin power connector 2-pin UTP connector MOUNTING The TW3001AR receiver is 3 rack units high and can be mounted into a fiber rack, onto a wall using a fiber wall mount kit or into the supplied wall clip. USING A RACK You can mount a TW3001AR into either an RK5000PS-3U (for power) or an RK5000-3U.
USING A WALL CLIP To attach the TW3001AR receiver to a wall using the supplied wall clip, refer to Figure 2 and do the following: 1. Attach the wall clip to a wall using two screws (not supplied). 2. Slide the receiver into the clip until the two holes on the bottom of the receiver align with the two holes on the lower flange of the clip. 3. Attach the receiver to the clip using the two Phillips pan head screws provided with the clip.
SETTING THE DIP SWITCHES You can override the adaptive technology by manually adjusting switches 1-4 on the DIP Switch. The factory default switch positions are shown in Figure 3. Switches 1-4 are set to AUTO and Switch 5 is set to High Mode. Figure 3. Default Switch Positions If you want to transmit video over 4,000 feet (1,219 meters) of UTP cable, set switch 1 to 4K.
APPLICATIONS You can connect the TW3001AR active receiver to transmitters, such as the TW3001P passive transceiver and the TW3001AT active transmitter, and to Pelco UTP cameras, such as the CC3710/CC3610 Series. Although you can connect these products using an unshielded twisted pair Cat3 and Cat5 cable, Cat5e and Cat6 are recommended for the best video performance. Always connect the UTP wires on the Cat cable from + to + and from - to -.
Figure 4 shows a TW3001AR connected to a UTP camclosure. TW3001AR POWER FROM RK5000PS-3U OR 12 VDC OR 24 VAC POWER SUPPLY + - CAMCLOSURE UTP BLUE WIRE = MONITOR GRAY WIRE = Figure 4.
Figure 5 shows a TW3001AR connected to a UTP fixed camera. TW3001AR POWER FROM RK5000PS-3U OR 12 VDC OR 24 VAC POWER SUPPLY + - FIXED CAMERA UTP PIN 5 + PIN 4 - MONITOR 10 PINS (5-/6+) 8 PINS (4-/5+) Figure 5.
Figure 6 shows a TW3001AR connected to a UTP Spectra dome for Coaxitron PTZ control. TW3001AR POWER FROM RK5000PS-3U OR 12 VDC OR 24 VAC POWER SUPPLY SPECTRA + VC-UTP BOARD COAXITRON UTP VIDEO MATRIX MONITOR Figure 6.
Figure 7 shows a TW3001AR connected to a TW3001P passive transceiver. The TW3001P then connects to a non-UTP fixed camera. TW3001AR POWER FROM RK5000PS-3U OR 12 VDC OR 24 VAC POWER SUPPLY + - UTP TW3001P DIRECT CONNECTION FIXED CAMERA MONITOR Figure 7.
Figure 8 shows a TW3001AR connected to a TW3032P passive transceiver. TW3001AR POWER FROM RK5000PS-3U OR 12 VDC OR 24 VAC POWER SUPPLY + - TW3032P UTP MONITOR Figure 8.
Figure 9 shows a TW3001AR connected to a TW3004P passive transceiver. The TW3004P then connects to a non-UTP fixed camera. TW3001AR TW3004P POWER FROM RK5000PS-3U 12 VDC OR 24 VAC POWER SUPPLY OR + - 4 3 UTP MONITOR 2 FIXED CAMERA 1 Figure 9.
Specifications ELECTRICAL Input Voltage Power Consumption Wire Type Wire Category DC Loop Resistance Differential Capacitance Transient Immunity Insertion Loss 12 VDC or 24 VAC, 50-60Hz 2.
C1666M-A (4/06)
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted pair transmission products. • Three years on Genex® Series products (multiplexers, server, and keyboard).
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.