Installation/Operation MC3610 and MC3710 Series Black-White Camera C2913M-F (08/05) Pelco Worldwide Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.
® Pelco, the Pelco logo, Spectra, Genex, Legacy, Esprit and Camclosure are registered trademarks of Pelco. ™Endura and ExSite are trademarks of Pelco ™DLP is a trademark of Texas Instruments, Inc. ™SuperHAD CCD is a trademark of the Sony Corporation. © Copyright 2005, Pelco. All rights reserved.
CONTENTS IMPORTANT SAFETY INSTRUCTIONS ........................................................................................................... 4 REGULATORY NOTICES ................................................................................................................................. 5 DESCRIPTION ................................................................................................................................................... 5 Models ...........................................
IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
REGULATORY NOTICES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAMERA LAYOUT Figure 1. Camera Layout INSTALLATION Lens Mounting MC3610 and MC3710 Series cameras can use fixed iris, manual iris, auto iris, or direct drive lenses. Cameras are factory-set for CS-mount lenses, but are easily adjusted for C-mount lenses. 1. C-Mount Lens Only - Loosen the two back focus locking screws. Rotate the back focus adjustment ring fully counterclockwise before installing the C-mount lens (refer to the section on Back Focus Adjustment). 2. Screw the lens onto the lens mount.
Camera Mounting Mounting points are provided on the top and bottom of the camera and are used to mount the camera on a bracket or tripod. They are designed to accept standard photographic mounting bolts (1/4-inch UNC-20). The mounting bracket must be capable of supporting the weight of the camera and its lens. NOTE: Some installation codes dictate that the mounting bracket must be capable of supporting up to four times the combined weight of the camera and lens. Figure 3.
Power Connections MC3610 and MC3710 Series cameras are available in AC high voltage and AC/DC low voltage types. The voltage required to operate the camera is clearly marked on the rear panel of the camera. The green POWER LED on the rear panel indicates that power is connected. Power low voltage cameras only from a UL Listed Class 2 isolated power supply. Power consumption is 4 watts.
Table B. Wiring Distances for 5 VA Cameras (24 VAC/12 VDC) The following are the recommended maximum distances for low voltage cameras. These distances are calculated with a 10 percent voltage drop. (Ten percent is generally the maximum allowable voltage drop for AC-powered devices.) Wire Gauge 24 VAC 12 VDC AWG mm2 Feet Meters Feet Meters 24 22 20 18 16 14 12 10 0.25 0.35 0.5 1 1.5 2.
Genlock Connection (MC3710H Series Only) Genlock (short for generator lock) is a system that allows the synchronization of two or more cameras to a specific timing signal. The signal may come either from one of the cameras (a 1 V peak-to-peak video signal) or from an external generator (a standard sync plus blanking signal). Genlock synchronization allows you to switch the video source displayed on a monitor without noticeable jump or roll in the video.
RJ45-10 Connections The RJ45-10 connector allows video (composite and twisted pair except MC3710S models) and power connections to be made to the camera using a single Cat5-style cable. NOTE: The PCM150 camera mount is designed for the MC3610 and MC3710 Series camera. It comes with preconfigured auxiliary connectors and cables as well as an easy-to-wire adapter plate. Before installation, identify the RJ45-10 connector leads to be used.
To send composite video through the RJ45-10 connector: 1. Connect composite video out to pin 3. 2. Connect composite video ground to pin 2. Unshielded Twisted Pair (UTP) Pins 5 and 6 allow video to be transmitted over unshielded twisted pair (UTP) wiring to equipment fitted with a suitable receiver (except MC3710S models). Ensure that connection polarity is observed in relation to the connected twisted pair receiver. To implement UTP, you must use 5-pair unshielded twisted cable, Cat5e, or an equivalent.
CAMERA SETUP Lens Setup and Focus Procedures Video Drive or Direct Drive (DC) Auto Iris Lens 1. Set the ESC switch and AGC switch to OFF. 2. Adjust the lens for the optimum picture. Video Drive. Refer to the lens instructions and adjust the lens for the optimum picture (video output level of 1 V peak-to-peak). Direct Drive. Use an appropriate screwdriver to turn the lens level potentiometer (refer to Figure 1) fully clockwise.
Back Focus Adjustment The back focus adjustment is located at the front of the camera and is accessible from either side of the case. To adjust the back focus: 1. Loosen the two back focus locking screws (one on each side). 2. Turn the back focus ring counterclockwise until the CCD sensor assembly is as far away from the back of the lens as possible. 3. Turn the back focus ring clockwise until focus is achieved. 4. When the back focus adjustment is satisfactory, tighten the locking screws.
Switch Settings Figure 9. Switch Settings (White indicates default switch position.) NOTE: Under most conditions, no setting of switches will be required. Please read the details of each switch before making any adjustments. AGC (Automatic Gain Control) - Switch Setting 1 Automatically adjusts the image to compensate for low levels of illumination. Choose between the following settings: ON (Default setting) - Enables the AGC mode. OFF - Disables the AGC mode.
Flickerless - Switch Setting 4 The flickerless setting can reduce the flicker caused by certain lighting conditions. The Electronic Shutter Control must be off for the correct operation of the flickerless function. Choose between the following settings: ON - Enables the Flickerless mode. OFF (Default setting) - Disables the Flickerless mode. INT/LL Synchronization Selection - Switch Setting 5 Line lock (LL) locks the frame rate to the power supply frequency.
Camera Synchronization When using more than one camera power supply, a brief vertical roll may occur on the monitor when a camera view is switched. To eliminate this vertical roll, it is necessary for the cameras to be synchronized. If the cameras are connected to certain Pelco matrix products, the cameras will automatically lock to the pulse signal that is transmitted up-the-coax. If not, it will be necessary to synchronize manually.
SPECIFICATIONS GENERAL Imaging Device: Picture Elements MC3710H and MC3610H: MC3710S: Sensing Area: Scanning System EIA: CCIR: Synchronization System: Horizontal Resolution MC3610H models: MC3710S models: MC3710H models: Iris Control: Electronic Shutter Range EIA: CCIR: Auto Iris Lens Type: Minimum Illumination MC3610H models: MC3710S models: MC3710H models: Signal-to-Noise Ratio: Vertical Phase: Automatic Gain Control: Electronic Shutter Control: Backlight Compensation: Flickerless Mode: Internal Sync: Sig
MECHANICAL Lens Mount: Camera Mount: C/CS mount (adjustable) 1/4–inch UNC-20 screw, top or bottom of camera housing ENVIRONMENTAL Operating Temperature: Storage Temperature: Operating Humidity: Storage Humidity: 14° to 122°F (-10° to 50°C) 14° to 158°F (-10° to 70°C) 20% to 80%, non-condensing 20% to 90%, non-condensing PHYSICAL Dimensions: Weight (without lens): 5" L x 2.9" W x 2.6" H (12.8 x 7.2 x 6.7 cm) 0.8 lb (0.4 kg) (Design and product specifications subject to change without notice).
[ 20 ] Pelco Manual C2913M-F (08/05)
Pelco Manual C2913M-F (08/05) [ 21 ]
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex® Series products (multiplexers, server, and keyboard).
REVISION HISTORY Manual # C2913M C2913M-A 0 C2913M-B C2913M-C C2913M-D C2913M-E C2913M-F Date 05/04 7/04 09/04 11/04 11/04 12/04 08/05 Comments Original version. Lens connector pin out changed. Clarified instructions for UTP use. Added UL warning for high-voltage models. Revised safety instructions. Revised back focus instructions and table C. WEEE directive added.Warranty and return information amended.
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.
