INSTALLATION/OPERATION IXE Series Extended Platform Network Camera Sarix Technology ™ C2953M-B (10/09)
Contents Important Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Legal Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . .
Configuring Auto Focus Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Configuring Manual Focus Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Setting Tone Map Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
List of Illustrations 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 4 Camera Connections and Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Remove Back Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Notices LEGAL NOTICE SOME PELCO EQUIPMENT CONTAINS, AND THE SOFTWARE ENABLES, AUDIO/VISUAL AND RECORDING CAPABILITIES, THE IMPROPER USE OF WHICH MAY SUBJECT YOU TO CIVIL AND CRIMINAL PENALTIES. APPLICABLE LAWS REGARDING THE USE OF SUCH CAPABILITIES VARY BETWEEN JURISDICTIONS AND MAY REQUIRE, AMONG OTHER THINGS, EXPRESS WRITTEN CONSENT FROM RECORDED SUBJECTS.
Introduction The IXE Series is an extended platform network-based camera with a built-in, Web-based viewer for live streaming to a standard Web browser (Microsoft® Internet Explorer® or Mozilla® Firefox®). The camera features open architecture connectivity for third-party applications and is also Endura Enabled™ and compatible with Digital Sentry® to record, manage, configure, and view multiple live streams. The camera supports two compression formats and many resolutions.
GETTING STARTED Before installing your camera, thoroughly familiarize yourself with the information in this section. NOTES: • Pelco recommends connecting the camera to a network that uses a Dynamic Host Configuration Protocol (DHCP) server to address devices. • Do not use a network hub when configuring the network settings for the camera. • To ensure secure access to the IP camera, place the camera behind a firewall when it is connected to a network.
ACT Product Overview 24V~ RELAY ALARM ACC RESET LINK PoE R1 A1 (FRONT COVER OPENED) F V Figure 1.
ì RJ-45 Network Port: Connects the camera to the IP network. Also supplies power to the camera through the network using PoE. If PoE is not available, the camera is prewired for 24 VAC. î ï ñ ó Ethernet Activity LED: Flashes green to indicate that data is being transmitted or received by the camera. r Reset Button: Reboots the camera or restores the camera’s factory default settings. This button is recessed.
Installation NOTE: Megapixel lenses are designed and tested to deliver optimal image quality to megapixel cameras. A standard definition lens installed on a megapixel camera will limit the resolution of the camera and create poor image quality. 1. Install the lens. a. Remove the cover from the lens mount. b. Screw the lens onto the lens mount. Be careful to prevent dust from entering the space between the lens and the imager.
4. For FCC Class B installations, attach the supplied ferrite to the network cable (refer to Figure 5). The ferrite should be installed on the cable approximately 1 inch (2.54 cm) from the camera’s RJ-45 network port. Figure 5. Ferrite Installation WARNING: The ferrite must be installed for the camera to meet FCC Class B compliance standards. Failure to correctly install the ferrite might cause harmful interference to radio communications. 5.
SERVICE CABLE The camera includes a service port that outputs camera video. Use it at the installation site to set up the field of view and to focus the camera. Pelco offers an optional service cable (IX-SC) that plugs directly into the service port. To access the service port, you must slide down the front cover front cover down (refer to Figure 1 on page 8). The service cable has a male BNC output for most standard viewers. NOTE: The ICS-SC and CST150 are not compatible with this camera.
WIRING CAT5 CABLE Connect a Cat5 cable to an RJ-45 network connector (not supplied). The 8-pin connector includes video and PoE for the camera. PoE (IEEE 802.3af) injects power over the same cabling that carries the network data, eliminating the need for a separate power supply. This simplifies the installation and operation of the camera without affecting network performance. NOTE: The camera will autosense and configure itself to use either a crossover cable or a straight cable.
ALARM, RELAY, AND 24 VAC CONNECTOR Single Camera Wiring If PoE is not available: 1. Connect the alarm, relay, and 24 VAC wires to the supplied mating connector (refer to Figure 8). NOTE: Only use the 24 VAC wires if PoE is not available. 2. When finished, attach the mating connector to the green connector on the back of the camera. Multiple Camera Wiring If you are operating the camera using 24 VAC and you are wiring more than one camera to the same transformer: 1.
Connecting Alarms The camera provides an alarm input for external signaling devices, such as door contacts or motion detectors. Both normally open and normally closed devices are supported. Supervised Alarms When an alarm is configured as a supervised alarm, the camera maintains a constant electrical current through the alarm circuit (3.3 VDC, 1 ohm). If the alarm circuit length changes, due to an electrical short or a bypass, the voltage fluctuates from its normal state and activates an alarm.
Unsupervised Alarms When an alarm is configured as an unsupervised alarm, the camera only activates an alarm when the normal alarm state (open or closed) changes. Figure 12 illustrates the alarm and no alarm conditions of an unsupervised alarm input. NORMALLY CLOSED NO ALARM GND NORMALLY OPEN +V NO ALARM GND +V ALARM GND +V ALARM GND +V ALARM GND +V NO ALARM GND +V +V ALARM GND CUT NO ALARM GND CUT +V BYPASS BYPASS Figure 12.
Operation CAMERA CONFIGURATION SEQUENCE Once the camera is installed and power is applied, the camera will start a configuration sequence: the green LED flashes five times per second for approximately two minutes and then glows solid green, indicating that the boot cycle is complete and the camera is on line. NOTE: If the camera is not connected to a Dynamic Host Configuration Protocol (DHCP) server and DHCP is enabled, the configuration sequence might take up to five minutes to complete.
ACCESSING THE IP CAMERA The first time you access the camera, the live video page appears. By default, you are viewing the video as a public user and only have access to the single stream live view. If, for security purposes, users should not be allowed to view video without first logging on to the camera, change the permissions for public users. LOGGING ON TO THE CAMERA 1. Open the Web browser. 2. Type the camera’s IP address in the browser address bar.
Live Video Page The live video page allows you to manage the way you view live video and capture images. You can also view live video from this page and access menus on the navigation bar (based on user permissions). Figure 15.
LIVE VIDEO PAGE ICONS Viewable icons are based on user permissions. Show Device List: Displays a list of viewable cameras connected to the same virtual local area network (VLAN) as the camera to which you are logged on. Disable Viewer: Closes the live view window. 1 x 1 Mode: Displays a single video pane. 2 x 2 Mode: Displays 4 video panes in rows of two. 3 x 3 Mode: Displays 9 video panes in rows of three. 4 x 4 Mode: Displays 16 video panes in rows of four.
SELECTING A STREAM 1. Click the Select Stream button. 2. Select one of the following stream options from the Select Stream page: Primary Stream: To select this stream, click the button next to Primary Stream. Secondary Stream: To select this stream, click the button next to Secondary Stream. QuickView Stream: To select this stream, click the button next to QuickView Stream. NOTES: • If the secondary stream has not been configured, only Primary Stream and QuickView Stream are available.
TAKING A SNAPSHOT 1. Click the “Take a Snapshot” button. 2. The File Download dialog box opens, and the following message appears: “Do you want to open or save this file?” 3. Select one of the following options: Open: Your computer’s photo editing program opens and displays the screen image. This function is available only when using Microsoft® Internet Explorer® 7.0 (or later) or Mozilla® Firefox® 3.0 (or later). Save: The image is saved as a JPEG file on your computer.
Settings Page Depending on user permissions, the Settings page allows you to manage camera system settings, set up users and groups, and control the camera. NOTE: The Settings menu might not be available if the user does not have permission to access this feature. ACCESSING THE CAMERA MENUS 1. Log on to the camera. 2. Click the Settings link in the navigation bar located in the upper-right corner of the page; a list of menu tabs appears. 3.
System Tab The System tab includes configurable and read-only fields. The General Settings and Time Settings fields are configurable. The System Information fields are read-only and include the firmware version, hardware version, model number, and serial number of the system. This information is typically required by Pelco Product Support for troubleshooting purposes. You can also use the System Tab to generate a system log, reboot the camera, or to restore the camera's factory default settings. Figure 17.
CHANGING THE DEVICE NAME 1. Click the System tab. 2. Click the Device Name box and highlight the text. 3. Type a user-friendly name into the Device Name box (2 to 64 characters). A user-friendly name makes it easier to recognize the device on the network. Examples of user-friendly names are Front Door, Lobby, or Parking Lot. 4. Click Save to save the new device name, or click Reset to restore to the previously saved device name. CONFIGURING THE TIME SETTINGS 1. Click the System tab. 2.
Network Tab Use the Network tab to change the camera’s general network settings, configure Secure Sockets Layer (SSL), and enable Secure Shell (SSH). General Network Settings The General Network page includes programmable and read-only fields for network communication settings. Available settings include the Hardware Address, Hostname, IP Address, Subnet Mask, Gateway, and DNS Servers. You can also enable or disable the Dynamic Host Configuration Protocol (DHCP) server from the General Network page.
TURNING ON DHCP The default Dynamic Host Configuration Protocol (DHCP) setting for the camera is DHCP On. If the DHCP option is set to Off, complete the following steps to reset it to On. 1. Place your mouse pointer over the Network tab. 2. Select General from the drop-down menu. 3. Select the On option for DHCP. 4. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.
SELECTING THE SECURE SOCKETS LAYER MODE Figure 18. SSL Configuration Page 1. Place your mouse pointer over the Network tab. 2. Select SSL from the drop-down menu. 3. Select one of the following modes: Required: A signed Secure Sockets Layer (SSL) certificate must be installed, and a secure URL that begins with the protocol name “https:” must be used to access the camera. Sensitive data is always encrypted during transmission.
GENERATING A CERTIFICATE REQUEST 1. Place your mouse pointer over the Network tab. 2. Select SSL from the drop-down menu. 3. Click the Install Certificate button located at the bottom of the SSL Configuration page. The Select Certificate Install Method option buttons appear on the page. 4. Select Generate Certificate Request, and then click Next. The Certificate Request Form opens. 5. Fill in all of the fields, and then click Generate Request.
ENABLING SECURE SHELL Figure 19. SSH Settings Page 1. Place your mouse pointer over the Network tab. 2. Select SSH from the drop-down menu. 3. Select the Enabled check box. NOTE: The username is always root and cannot be changed. The username and password are required when accessing the camera through a third-party SSH client. 4. Click in the Password box and type a password (4 to 16 alphanumeric characters). Passwords are case-sensitive. 5. Click in the Re-type Password box and retype your password. 6.
Imaging Tab Use the Imaging tab to change the camera’s general image settings, adjust the camera exposure, program the focus mechanism, adjust the tone map settings to increase scene detail, or tune the white balance settings for scenes with fluctuating lighting conditions. General Imaging Settings General imaging settings include adjustments for camera orientation and digital processing. The Orientation settings reconfigure the image 180 degrees horizontally and 180 degrees vertically.
CONFIGURING THE ORIENTATION OF THE SCENE Figure 20. Orientation Page 1. Place your mouse pointer over the Imaging tab. 2. Select General from the drop-down menu. 3. Select one of the following options: 32 • Click the “Flip left-to-right” box to rotate the camera image 180 degrees horizontally. • Click the “Flip top-to-bottom” box to rotate the camera image 180 degrees vertically.
CHANGING THE DIGITAL PROCESSING SETTINGS Figure 21. Digital Processing Page 1. Place your mouse pointer over the Imaging tab. 2. Select General from the drop-down menu. 3. Select the mode: Manual or Auto. Auto is the default. 4. Move the slider to the left or right to change the following settings: Sharpness Adjust/Sharpness: Controls the clarity of detail in a scene. Move the slider to the right to increase the sharpness; move the slider to the left to decrease the sharpness.
SELECTING AUTO EXPOSURE SETTINGS Figure 22. Auto Exposure Page 1. Place your mouse pointer over the Imaging tab. 2. Select Exposure from the drop-down menu. 3. Select the Auto mode. 4. Select the Light Control mechanism that controls the exposure time of the camera. Digital Exposure: The camera controls the exposure time. This setting automatically adjusts the exposure time depending on the light level of the scene, up to the maximum exposure time setting.
7. Day/night cameras only: Set the Day Exposure Time and the Night Exposure Time. Day Exposure Time: This setting is the maximum time in milliseconds that an image is exposed during daytime conditions. Decreasing exposure time decreases the light sensitivity of the scene and reduces the streaking of fast moving objects (motion blur); however, it increases the amount of noise in the scene. The day maximum exposure time range is 1 to 500 msec; the default setting is 33.3 msec.
SELECTING MANUAL EXPOSURE SETTINGS Figure 23. Manual Exposure Page 1. Place your mouse pointer over the Imaging tab. 2. Select Exposure from the drop-down menu. 3. Select the Manual mode. 4. Move the Analog Gain slider to the desired position. Increasing the gain increases the brightness of the image, but it also increases the amount of noise in the image. The analog gain range is 1.00 to 15.75; the default setting is 1.00. 5. Move the Exposure Time slider to the desired position.
DAY NIGHT SETTINGS The Day Night mode controls the position of the IR cut filter, which determines the color or black-white setting of the camera. The Day Night mode settings change depending on the Exposure settings. If the camera is set to Auto Exposure mode, the Day Night mode can be set to Auto or Manual and all of the respective settings are available.
CONFIGURING AUTO FOCUS SETTINGS Figure 24. Auto Focus Page 1. Place your mouse pointer over the Imaging tab. 2. Select Focus from the drop-down menu. 3. Select the Auto mode. 4. Set the Temperature Change Refocus setting. The camera is programmed to run a quick automatic focus sequence when the internal temperature sensor of the camera detects an environmental temperature change of 41°F (5°C). This focus sequence adjusts the center focal point of the scene to maintain optimal focus.
CONFIGURING MANUAL FOCUS SETTINGS Figure 25. Manual Focus Page NOTE: It is recommended to set the focus to Manual when using analytics. If the focus is set to Auto, significant background changes will occur when the camera automatically adjusts to different points within a scene resulting in frequently changing image sharpness. This may cause problems with scene recognition, which will suspend analytics operation or cause false alarms. 1. Place your mouse pointer over the Imaging tab. 2.
SETTING TONE MAP OPTIONS Figure 26. Tone Map Page 1. Place your mouse pointer over the Imaging tab. 2. Select Tone Map from the drop-down menu. 3. Move the Tone Map sliders to adjust the following image settings: Black Clip Percent: Adjusts the percent of pixels set to black. Move the slider to the right to darken the scene by increasing the number of pixels that are mapped to absolute black. The black clip percent range is 0 to 25; the default setting is 0.5.
SELECTING AUTO WHITE BALANCE SETTINGS Figure 27. Auto White Balance Page 1. Place your mouse pointer over the Imaging tab. 2. Select White Balance from the drop-down menu. 3. Select the Auto mode. 4. Move the sliders to adjust the following settings in Auto mode: Red Gain Adjust: Adjusts the image output in the red range. Move the slider to the right to increase the red level; move the slider to the left to decrease the red level. As you move the slider, you will see the color change on your monitor.
SELECTING MANUAL WHITE BALANCE SETTINGS Figure 28. Manual White Balance Page NOTE: Manual white balance is recommended only for indoor applications that have a single, unchanging primary light source. 1. Place your mouse pointer over the Imaging tab. 2. Select White Balance from the drop-down menu. 3. Select the Manual mode. 4. Move the sliders to adjust the following settings in Manual mode: Red Gain: Adjusts the image output in the red range.
A/V Streams Tab Use the A/V Streams tab to configure the video and audio streams for the camera. The A/V Streams tab includes a Video Presets page, a Video Configuration page, and an Audio Configuration page. Video Presets The Video Preset page includes three fully-configured video presets, which include primary and secondary video stream settings for easy setup. These presets may also be used as a starting point for a custom video configuration. These preset configurations vary depending on camera model.
SELECTING A VIDEO PRESET CONFIGURATION Figure 29. Select Video Preset Configuration Page 1. Place your mouse pointer over the A/V Streams tab. 2. Select the Video Preset option from the drop-down menu. 3. Click the button next to the video preset stream configuration (High, Medium, or Low) that you want to select. 4. Click the Save button to save the settings, or click the Reset button to clear your selection without saving it.
CONFIGURING A CUSTOM VIDEO STREAM CONFIGURATION Figure 30. Custom Video Stream Configuration Page 1. Place your mouse pointer over the A/V Streams tab. 2. Select Video Configuration from the drop-down menu. 3. Click both of the Clear buttons to delete the primary and secondary streams settings. 4. Optional: In the Primary Stream section, type a user-friendly name in the Name box (2 to 64 characters). A user-friendly name makes it easier to recognize the stream (for example, Live and Recording). 5.
COMPRESSION STANDARDS JPEG: A commonly used video compression scheme, also known as MJPEG. JPEG has the least impact on the camera's processor, but it requires the most bandwidth. H264: A new version of MPEG-4 compression used in high-definition video players such as Blu-ray™ and HD-DVD. H.264 is the most processor-intensive, but it requires the least amount of bandwidth. AVAILABLE CAMERA RESOLUTION Refer to the following table for the resolution capabilities of your camera model Table B.
ENDURA SIGNING Enabling the Endura Signing feature allows an Endura® system to authenticate video from an Endura recorded stream. This setting is only available with H.264. RATE CONTROL The rate control setting determines the bit rate and quality of each frame in the video stream. There might be a trade-off between image quality and the resources required for video storage when selecting a rate control setting. CBR: The constant bit rate (CBR) streams video at a fixed number of bits per second.
SELECTING THE AUDIO CONFIGURATION SETTINGS To use audio with the camera you must have an audio device connected to the accessory port located on the back of the camera. Once the device is connected, audio can only be enabled through the primary stream. Audio and video is not synced when viewing and listening to the primary stream through a Web browser. You will experience a three-second delay in video when viewing the primary stream with audio.
Users and Groups Tab Use the Users and Groups tab to create and manage user accounts, group permissions, and to change the way the camera manages the users and groups settings. Users User accounts can be created and added to groups to limit the permissions given to individuals logged on to the camera. Use the features on the Users page to create, modify, or delete user accounts. NOTE: The only defined user that cannot be deleted is admin; however, the administrator password can be changed.
Groups Groups can be created to assign permissions to users within each group. Use the features on the Groups page to create, modify, and delete groups and permissions. Multiple permissions can be assigned to each group. Figure 33. Group Page Refer to the following sections for more information.
CREATING A NEW USER 1. Place your mouse pointer over the Users and Groups tab. 2. Select Users from the drop-down menu. 3. Click in the Username box and type a user name (2 to 23 alphanumeric characters). User names are not case-sensitive and are saved in lowercase characters. 4. Click in the Password box and type a password (4 to 16 alphanumeric characters). Passwords are case-sensitive. 5. Click in the Retype Password box and retype your password. 6.
CREATING A NEW GROUP 1. Place your mouse pointer over the Users and Groups tab. 2. Select Groups from the drop-down menu. 3. Click in the Group Name box and type a name for the group you are creating (2 to 23 alphanumeric characters). 4. Click in the Description box and type a description for the group you are creating (2 to 23 alphanumeric characters). 5. Select the appropriate check boxes to choose the permissions you want to assign to this group. 6.
GENERAL SETTINGS FOR USERS AND GROUPS The general settings for user and groups allow you to change the way the camera manages the users and groups settings. These settings can be managed on a camera-to-camera basis or by using a centralized server to apply changes to multiple cameras. Figure 34. User and Group Settings Page The available general settings for users and groups are as follows: Standalone: The camera manages its users and groups locally.
Events Tab Use the Events tab to program sources and handlers to manage camera events. Sources Figure 35. New Event Source Page An event is a preprogrammed camera function that is automatically activated by an event source. The camera supports three types of event sources: Alarm Source: The camera supports one alarm source. The sources are the camera inputs for external signaling devices, such as door contacts or motion detectors. System Source: A system source is activated when the camera restarts.
Handlers Figure 36. New Event Handler Page Event handlers are the actions that the camera takes when an event occurs. The camera supports four event handlers. Send Email: Sends an email to a defined email address when an event is activated. The SMTP server must be configured to accept the camera IP address. Write JPEG to SD Card: Saves a JPEG of the activated event to a mini SD card. An SD card must be installed in the device for this handler to function. NOTE: The mini SD card must be formatted as FAT32.
CREATING AN ALARM EVENT SOURCE 1. Place your mouse pointer over the Events tab. 2. Select Sources from the drop-down menu. 3. Click in the Name box and type a user-friendly name (2 to 23 alphanumeric characters). 4. Select Alarm from the Type drop-down menu. 5. Move the Dwell Time slider to set the amount of time in seconds that the alarm is active. The dwell time range is 0.1 to 200 seconds; the default setting is 0.1. 6. Select either normal or reversed from the Polarity drop-down menu. 7.
DELETING AN EVENT SOURCE 1. Place your mouse pointer over the Events tab. 2. Select Sources from the drop-down menu. 3. Click the source profile that you want to delete from the defined source box located on the left side of the page. 4. Click the Delete Source button. A dialog box appears with the message “Are you sure you want to delete the source?” 5. Click OK. The source profile is deleted from the defined source box.
CREATING AN EVENT HANDLER: WRITE JPEG TO SD CARD 1. Install an SD card in the mini SD card slot located on the back of the camera. NOTE: The mini SD card must be formatted as FAT32. Other formats are not compatible with the camera. 2. Place your mouse pointer over the Events tab. 3. Select Handlers from the drop-down menu. 4. Click in the Name box and type a user-friendly name (2 to 23 alphanumeric characters). 5. Select “Write JPEG to SD Card” in the Type drop-down menu. 6.
CREATING AN EVENT HANDLER: OPEN/CLOSE RELAY 1. Place your mouse pointer over the Events tab. 2. Select Handlers from the drop-down menu. 3. Click in the Name box and type a user-friendly name (2 to 23 alphanumeric characters). 4. Select Open/Close Relay in the Type drop-down menu. 5. Move the On Time slider to set the amount of time that the relay will remain open. The time range is 0.1 to 200 seconds; the default setting is 0.1. 6.
EXAMPLE HANDLER FILTER SETUP If you do not want a handler activated every time an event occurs, use the filter fields to limit handlers. For example, you only want a handler activated when an event occurs after business hours. Your business is open Monday through Saturday, 8:00 a.m. to 6:00 p.m., and it is closed on Sunday. 1. Create a handler for Monday through Saturday: a. Select the day filter fields Monday through Saturday. b. Type 0000 in the Start box and 0800 in the End box. c.
Help Menu Online Help documents the basic instructions for configuring the camera. Click the Help hyperlink in the navigation bar to access these instructions. Log Off Menu To log off, click the Log Off button in the navigation bar. A login dialog box appears.
Specifications Models IXE20C 2.1 megapixel extended platform network color camera IXE20DN 2.1 megapixel extended platform network day/night camera IXE20C-PM Sarix IXE Series, extended platform network camera, 2.1 megapixel color with built-in Pelco Standard Suite IXE20DN-PM Sarix IXE Series, extended platform network camera, 2.1 megapixel day/night with built-in Pelco Standard Suite IXE20C-PO Sarix IXE Series, extended platform network camera, 2.
Electrical Port RJ-45 network connector for 100Base-TX; Auto MDI/MDI-X Cabling Type Cat5 or better for 100Base-TX Power Input 24 VAC or PoE (IEEE 802.3af class 3) Power Consumption (camera only) <7 W Current Consumption PoE 24 VAC <200 mA maximum <295 mA nominal; <390 mA maximum Local Storage Mini SD Alarm Input 10 VDC maximum, 5 mA maximum Relay Output 0 to 15 VDC maximum, 75 mA maximum Service Connector External 3-connector, 2.
Users Unicast Multicast Up to 20 simultaneous users Unlimited users H.264 Security Access Password protected Software Interface Web browser view and setup, up to 16 cameras Pelco System Integration Endura 2.0 (or later), Digital Sentry 4.2 (or later) Open IP Integration Pelco IP camera API Environmental Operational Temperature 14° to 122°F (-10° to 50°C) Storage Temperature 14° to 158°F (-10° to 70°C) Storage Humidity 20% to 90%, noncondensing Physical Dimensions 5.4” D x 3.1” W x 3.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
www.pelco.com Pelco, Inc.
