® CCC1300H-2, CCC1300H-2X, and MCC1300H-2 1/3-Inch CCD Camera Installation/ Operation Manual C1961M-B (3/01) Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • Pelco Online @ www.pelco.
CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ................................................................. 3 REGULATORY NOTICES ........................................................................................... 3 DESCRIPTION ................................................................................................................... 4 MODELS .....................................................................................................................
IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service and installation personnel. 2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approved materials. 3. Use only installation methods and materials capable of supporting four times the maximum specified load.
DESCRIPTION The CCC1300H-2, CCC1300H-2X, and MCC1300H-2 Digital Cameras are high resolution, compact video cameras that feature a 1/3-inch CCD imager. The camera’s high resolution and high-density image sensor ensure a sharp and clear picture over a wide range of conditions.
10 ESC - Electronic Sensitivity Control This function changes the sensitivity of the camera by varying the electronic shutter speed according to the amount of incident light. The ESC range is 1:300. To reset the ESC function switch, move the ON/OFF switch right or left. The ESC is factory set to the ON position. 11 BLC - Backlight Compensation The backlight compensation function allows fine picture correction to prevent the subject from being extremely dark due to strong backlight.
POWER CONNECTIONS To connect to the power supply: 1. Strip at least .50 inch (13 mm) from the power cord to expose the wires. 2. Insert the three wires into the holes in the terminal strip until they snap into place. 3. Confirm that the cord is connected to terminal securely by lightly tugging on the cord.
GENERAL LENS INFORMATION The CCC1300H-2, CCC1300H-2X, and MCC1300H-2 can use fixed, manual, or passive (DC-controlled) auto iris lenses. The camera has a standard CS lens mount, but can use a C-mount lens when a C/CS-mount adapter is installed between lens and camera. LENS MOUNTING 1. Screw the lens onto the lens mount. Be careful to prevent dust from entering the space between the lens and the CCD element. If necessary, use clean, compressed air to remove any foreign matter. 2.
5. Adjust the back focus. a. Use an Allen wrench to loosen the back focus lock screw at the side of the camera. b. Turn the lens mount to obtain the sharpest image on the monitor. c. Turn the back focus locking ring clockwise to tighten. NOTE: Do not over tighen the back focus lock screw. Over tightening the back focus lock screw can damage the threads on the mount of the lens. MOTORIZED ZOOM LENSES 8 1. With the camera operating, position the camera to view an object at least 70 feet (25 m) away.
CAMERA SYNCHRONIZATION The power supply of each camera is set to the same synchronized phase at the factory and usually does not need to be readjusted. When using more than one camera power supply, a brief vertical roll may occur on the monitor each time a camera view is switched. To eliminate vertical roll, adjust the phase control by synchronizing, or line locking, the cameras to one another. Use the LL switches on the back of the camera to make adjustments.
ECLIPSER ADJUSTMENT The eclipser is set at the factory and usually does not need to be readjusted. However, if fine tuning is necessary, do the following: 1. Set the DIP switches. a. AGC: OFF b. ELC: OFF c. BLC: OFF 2. Set the IRIS MODE selector. a. Auto iris lens controlled by video signal - VIDEO b. Auto iris lens controlled by DC voltage - DC 3. Set the variable resistors and Eclipse DIP switch. a. THRE: Counterclockwise b. ECLP: Mechanical center c. GRAY: Mechanical center d. ECLIPSER DIP: OFF 4.
SPECIFICATIONS GENERAL CCD Sensor: Picture Elements CCC1300H-2, MCC1300H-2: CCC1300H-2X: Sensing Area: 1/3-inch interline transfer 768H x 494V (approx. 380K) 752H x 582V (approx. 440K) 3/16 x 1/8 - inch (4.7 mm x 3.5 mm) Synchronize System: AC Line lock Horizontal Resolution CCC1300H-2, CCC1300H-2X: 470 TV lines MCC1300H-2: 560 TV lines Iris Control: Electronic/passive Minimum Illumination CCC1300H-2, CCC1300H-2X: 1.5 lux at f1.2, 75% highlight reflectance, at 77°F (25°C) MCC1300H-2: 0.15 lux at f1.
PELCO CCC1300H-2, CCC1300H-2X, and MCC1300H-2 Tested to Comply with FCC Standards FOR HOME OR OFFICE USE WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • • • • • • • • Five years on Pelco manufactured cameras (CC3500/ CC3600 and MC3500/MC3600 Series); two years on all other cameras.