® DD08 Intercept Dome Series Fixed mount Installation/Operation Manual C290M-A (6/99) PELCO • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981 FAX (800) 289-9150 or (1-559) 292-3827
TABLE OF CONTENTS Section Page 1.0 WARNINGS ........................................................................................................................................1 2.0 SCOPE ...............................................................................................................................................2 3.0 DESCRIPTION ................................................................................................................................... 2 3.1 MODELS .......
INSTALLATION/OPERATION MANUAL DD08 INTERCEPT DOME SERIES FIXED MOUNT 1.0 WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture. 3.
2.0 SCOPE 3.1 MODELS The information contained in this manual covers the DD08 Series fixed mount for the IDS08 Series Intercept Domes. The model designator is DD08XXX, where each “X” represents a feature that is essential for operation. This manual pertains only to the fixed mount. Proceed with installation of the fixed mount and the camera/lens once back box installation has been completed.
4.0 INSTALLATION 4.1.1 INSTALLING FIXED MOUNT 4.1 FIXED MOUNT INSTALLATION AND REMOVAL To install the fixed mount: 1. Turn off back box power switch, if applicable to your back box. (See Figure 1 for switch location.) 2. Remove the hairpin style safety pins from the two latches in the back box (see Figure 2). 3. Remove dome from fixed mount. This is only a pull apart procedure (refer to Figure 3.) 4. Grasp the fixed mount with two hands as shown in Figure 4. 5.
4 Figure 1. Back Box Power Switch Location Figure 3. Removing/Attaching Dome to Fixed Mount Figure 2. Removing Safety Pins Figure 4.
4.1.2 REMOVING FIXED MOUNT To remove the fixed mount: L = Latch P = Pin 1. Remove the back box bezel/trim ring as described in back box manual, C456M, and the dome. 2. Turn off back box power switch, if applicable to your model (see Figure 1). 3. Remove the two hairpin style safety pins from the back box latches (see Figure 2). 4. Open only one of the latches by pressing the latch arm with your finger. 5. Grasp the unit with one hand to prepare for the 510 lb (2.27-4.54 kg) load.
5.0 ADJUSTMENTS To adjust the horizontal and vertical position of the fixed mount perform the following steps: Figure 7. Locking Fixed Mount in Place 4.2 LENS WIRING Refer to back box manual, C456M, for wiring pinouts and wire lens according to manufacturers instructions . 4.3 CAMERA/LENS INSTALLATION Install the camera/lens you have selected for use with the IDS08 series dome as follows: 1.
7.0 SPECIFICATIONS MECHANICAL Pan: 360° movement in horizontal plane Tilt: -90° movement from horizontal plane Approximate Camera/Lens Size: Figure 8. Bezel Attachment 6.0 CARE AND MAINTENANCE Regularly scheduled maintenance will prolong the operational life and appearance of the equipment. Connectors Video: BNC Camera Power: Spade lugs GENERAL Construction Fixed Mount: IMPORTANT The acrylic dome is an optical surface.
8.0 EXPLODED ASSEMBLY DIAGRAM Figure 9.
8.1 MECHANICAL PARTS LIST The following parts list corresponds to the exploded assembly diagram in Figure 9. Item No. 1 2 3 4 5 6 7 8 9 Quantity 2 2 1 1 1 1 1 2 1 10 11 12 13 2 2 2 6 14 1 Description Bushing, delrin 3/8" ID x 5/8" OD Push nut, .
9.0 WARRANTY AND RETURN INFORMATION WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex® Series products (multiplexers, server, and keyboard).
