DX8000-UPDVD Upgrade Installation Manual DX8000 Digital Video Recorder C1604M (6/04)
Protecting people and property in a million locations worldwide.
Introduction The following instructions serve as an installation guide for the DX8000-UPDVD drive kit. PARTS LIST NOTE: This upgrade kit includes a Pelco-certified DVD-RW drive. Using any other drive voids the manufacturer’s warranty for the DX8000.
Getting Ready 1. Familiarize yourself with the instructions throughout this manual. 2. Check that you have all the necessary parts and tools. Refer to the Parts List and Tools Needed section. 3. Shut down the DX8000 Series DVR unit. Refer to DX8000 Installation Manual or Operations and Programming Manual for instructions on shutting down your unit. 4. Unplug the power cord from the wall socket and then from the rear of the DVR.
Figure 2.
5. Ensure that the DX8000 Series DVR and all of its components are protected against electrostatic discharge (ESD). Before handling any electronic components, you should take steps to ground yourself properly so that any built-up static electric charges are dissipated away from the unit. The most effective method for combating ESD is to use a properly grounded wrist strap.
Prepare Unit for Drive Installation OPEN THE UNIT CHASSIS WARNING: The chassis assembly includes parts with sharp edges. To avoid injury, use caution when working in and around the DX8000’s chassis and components. 1. If the DX8000 is mounted in a rack, remove it and transport it to an area that will provide full access to the unit chassis: a. b. c. Disconnect any cables or connections that might restrict access to or the removal of the unit. Unscrew the fasteners that are securing the unit in the rack.
3. Using a Phillips-head screwdriver, remove the chassis cover: WARNING: Make sure unit is turned off and you are wearing a properly grounded ESD wrist strap before attempting to open the DX8000 chassis cover. Refer to the Getting Ready section. a. Remove the two top-most screws on the left and right side panels of the DX8000. Refer to Figure 4. b. Remove the four silver screws fastening the cover to the rear of the unit. These screws are the ones closest to the top of the unit. Refer to Figure 4. c.
4. Using a Phillips-head screwdriver, remove the side panel from the side of the unit closest to the CD/DVD drive: a. b. Remove the four screws from the side panel. Refer to Figure 5. Set the panel and screws aside for use later. Figure 5.
COMPONENT LAYOUT Figure 6 shows the location of your DX8000 Series DVR’s major components. Certain cables and components have been omitted from the illustrations in this manual for the purpose of clarity. DIMM SOCKETS (RAM) POWER SUPPLY CD-RW CPU HARD DRIVE REAR OF DVR FRONT OF DVR VGA CARD PCI SLOT 1 2 3 4 5 6 REAR CROSS-BRACE MOTHERBOARD IDE CONNECTORS (SECONDARY) FRONT CROSS-BRACE MOTHERBOARD IDE CONNECTORS (PRIMARY) Figure 6.
Remove the Existing Optical Drive DISCONNECT THE CD/DVD DATA CABLE AND POWER WIRES When removing data cable and power wires, pull the connectors straight out. Do not rock connectors back and forth or remove a connector by pulling it by its wires or cable. 1. Remove the IDE data cable from the existing CD/DVD by carefully pulling the plastic cable tab away from the rear of the drive. Refer to Figure 7. 1 Figure 7.
2. Remove the power connector from the CD/DVD drive. Refer to Figure 8. 2 Figure 8.
REMOVE THE CD/DVD DRIVE 1. Using a Phillips-head screwdriver, unfasten the two screws that attach the CD/DVD to the chassis. Refer to Figure 9. 1 Figure 9.
2. Gently pull the CD/DVD drive out of the DVR through the front of the unit. Refer to Figure 10. 2 Figure 10.
Install the New DVD-RW Drive into the Unit 1. Insert the new DVD-RW into the DVR: a. b. Make sure the drive is oriented correctly. Insert the new DVD-RW into the DVR through the front of the unit. Refer to Figure 11. DVD-RW 1b Figure 11.
c. Using a Phillips-head screwdriver and the two screws provided in the upgrade kit, secure the drive to the unit’s chassis. Refer to Figure 12. Tighten the screws securely but do not over-tighten. 1c Figure 12.
RECONNECT THE DATA CABLE AND POWER WIRES IMPORTANT: Data and power connectors fit together only one way. All connectors are keyed to ensure that they are inserted in the proper orientation. Examine the drive, motherboard and cable connectors before installation so that connectors are properly aligned. Make sure connectors are seated in the mating connectors securely, but do not force the connection.
2. Connect the DVD-RW drive to the system motherboard using the existing data cable. Refer to Figure 14. 2 Figure 14.
Reassemble the Unit 1. Using a Phillips-head screwdriver, reattach the side panel you removed earlier. Refer to Figure 15. Figure 15.
2. Replace the chassis cover using the same screws you removed from the side and rear of the unit. Refer to Figure 16. Figure 16.
4. Reinstall the unit in a rack enclosure if necessary, and reconnect all cables and peripheral equipment that you removed earlier. 3. Plug the power cord back into the power supply and then into the wall. 4. Turn on the power switch and allow the unit to start up and find the new DVD-RW. This may take several minutes. ON/OFF Figure 17.
Notes 20 C1604M (6/04)
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • • • • • • • • • Five years on the following fixed camera models: CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X.
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East Pelco and the Pelco logo are registered trademarks of Pelco. Windows is a registered trademark of Microsoft Corporation. C1604M (6/04) © Copyright 2004, Pelco. All rights reserved.
