Data Sheet

ManualsBrandsPelco ManualsElectronicsEthernetConnect 4-Port Self Managed POE Switch

PRODUCT SPECIFICATION

transmission and power

C3978 / NEW 3-10-14

International Standards

Organization Registered Firm;

ISO 9001 Quality System

EC-4BY1SWC/U Series EthernetConnect

™

Switch

4-PORT, SELF-MANAGED, POE+ SWITCH WITH EXTENDED UPLINK

Product Features

• No Programming Required

• 10/100 Mbps Ethernet

– 4 x 10/100BASE-T/TX Electrical Ports Supporting PoE+

– 1 x 100 Mbps Extended Electrical Uplink

• Transmits Four Individual Ethernet Data Channels Over Standard

Cat5/Cat5e/Cat6 UTP Cable or Over Coaxial Cable

• Extends Ethernet up to 914 m (3,000 ft) at 10 Mbps or

610 m (2,000 ft) at 100 Mbps Over Cat5/Cat5e/Cat6 UTP Cable

• Extends Ethernet up to 1,524 m (5,000 ft) at 10 Mbps or

610 m (2,000 ft) at 100 Mbps Over Coaxial Cable

• Extended Temperature Operation of –40°C to 75°C (–40° to 167°F)

• 30 W PoE Capability on Ethernet Ports

• Electrical Ports Support Autonegotiation for 10 Mbps or 100 Mbps,

Full-Duplex or Half-Duplex Data

• Pre-Programmed Port for Uplink

• Full 10/100 Mbps Bandwidth

• Supports Multicast and Unicast

• Automatic MDI/MDI-X Crossover

• Designed to Meet Full Compliance with the Environmental

Requirements (Ambient Operating Temperature, Mechanical Shock,

Vibration, Humidity with Condensation, High-Line/Low-Line Voltage

Conditions and Transient Voltage Protection) of NEMA TS-1/TS-2 and

the Caltrans Specification for Traffic Signal Control Equipment

• Voltage Transient Protection on all Power and Signal Input/Output

Lines Provides Protection from Power Surges and Other Voltage

Transient Events

• Power and Activity Status LED Indicators

• Hot-Swappable Rack Modules

• Interchangeable Between Stand-Alone or Rack Mount Use

• IEEE802.3at Compliant

• Designed and Manufactured in the USA

The EthernetConnect

™

EC-4BY1SWC/U Series has two models

that provide different front panel connectors; the C model for coaxial

applications and the U model for UTP applications.

The EthernetConnect EC-4BY1SWC/U Series is an Ethernet switch

with uplink management functionality that operates on the Ethernet

over copper (EoC). It provides four ports operating at 10/100 Mbps

and is designed to combine these four electrical ports into a single

electrical extended port that forwards the data to the next network

device. The switch does not require programming prior to use.

The EC-4BY1SWC/U Series comes pre-programmed, preventing

network video flooding with DIP switch selection of the extended

distance port as uplink. Ports 1 through 4 can supply up to 30 W of

Power over Ethernet (PoE) and incorporate PoE+ features based on

the IEEE802.3at standard. Front panel LED indicators confirm the

operating status of the Ethernet switch.

The EC-4BY1SWC/U Series can be either wall-mounted or

chassis-mounted for rack installation. All application configurations

should be verified at time of ordering to facilitate ease of

installation.

EC-4BY1SWCPOE-W EC-4BY1SWUPOE-W

Summary of content (2 pages)

PAGE 1
PRODUCT SPECIFICATION transmission and power EC-4BY1SWC/U Series EthernetConnect™ Switch 4-PORT, SELF-MANAGED, POE+ SWITCH WITH EXTENDED UPLINK Product Features • No Programming Required • 10/100 Mbps Ethernet – 4 x 10/100BASE-T/TX Electrical Ports Supporting PoE+ – 1 x 100 Mbps Extended Electrical Uplink • Transmits Four Individual Ethernet Data Channels Over Standard Cat5/Cat5e/Cat6 UTP Cable or Over Coaxial Cable • Extends Ethernet up to 914 m (3,000 ft) at 10 Mbps or 610 m (2,000 ft) at 100 Mbps Over
PAGE 2
TECHNICAL SPECIFICATIONS GENERAL MODELS EC-4BY1SWCPOE-W EC-4BY1SWUPOE-W EthernetConnect 4-port coaxial self-managed PoE switch, 30 W per port, EoC using coaxial cable, extended uplink, wall mount EthernetConnect 4-port UTP self-managed PoE switch, 30 W per port, EoC using Cat5/ Cat5e/Cat6 UTP, extended uplink, wall mount Dimensions Operating Temperature Storage Temperature Relative Humidity Unit Weight Shipping Weight 15.5 x 13.5 x 2.8 cm (6.1" D x 5.3" W x 1.