® EH6500 Series Environmental Enclosure Installation/ Operation Manual C459M-E (1/96) Pelco • 300 W. Pontiac Way, Clovis, CA 93612-5699 • USA • Pelco Online @ http://www.pelco.
TABLE OF CONTENTS Section Page 1.0 WARNINGS ........................................................................................................................................ 1 2.0 SCOPE ...............................................................................................................................................2 3.0 DESCRIPTION ................................................................................................................................... 2 4.
LIST OF ILLUSTRATIONS Figure 1 2 3 5 6 7 8 Page EH6500 Series Enclosure Dimension Drawing ............................................................................... 2 Wiring Diagram for Blower and Heater, 120V ................................................................................. 3 Wiring Diagram for Blower and Heater, 230V ................................................................................. 4 Enclosure with Pan/Tilt and WM2000 Wall Mount with ST1 Strut ........................
(This page intentionally left blank.
INSTALLATION/OPERATION MANUAL MODEL EH6500 SERIES ENVIRONMENTAL ENCLOSURE 1.0 WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 4. Only use replacement parts recommended by Pelco. 1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes. 5. 2.
2.0 SCOPE 3.0 DESCRIPTION The information contained within this manual covers the EH6500 Series Environmental Enclosure. The EH6500 Series offers an environmental enclosure designed to accept ENG (Electronic News Gathering) cameras which are used in a variety of applications. The enclosure is constructed of 5052H32 aluminum and opens from the rear by releasing the two latches. Opening is assisted by dual gas springs, which securely holds the lid when fully opened. If necessary, the lid can be removed.
4.0 INSTALLATION 4.1 BLOWER AND HEATER ELECTRICAL CONNECTION (IF APPLICABLE) The heater and blower assemblies are factory pre-wired for power input and only require connection of power to the terminal block. Refer to Figure 2, 3 or 4 for the proper connections. MOTOR BLUE WHITE N.O . COM 80W @ 120VAC WHITE N.C. BLACK S1 WHITE WHITE 80W @ 120VAC 5 8 2 VIOLET 37.
MOTOR BLUE N.O. WHITE COM 80W @ 230VAC N.C. WHITE 80W @ 230VAC BLACK S1 WHITE WHITE 5 6 4 WHITE 1 + DIODE BRIDGE 10 2 VIOLET AC 8 - AC WHITE 37.5W DEFROSTER 120 VAC SOLENOID PUMP WHITE FAN 11 12 13 14 15 16 17 8 9 10 5 4 3 21 21 22 23 24 25 26 27 28 29 30 18 19 20 PCB9000255A LENS 1 2 3 4 5 6 7 VACINPUT INPUTWIRING WIRINGDIAGRAM DIAGRAM INPUT VAC WIPER TRIGGER INPUT LINE AC HIGH AC NEUTRAL GROUND WHITE 80W @ 230VAC WHITE WHITE 80W @ 230VAC WHITE WHITE 37.
WHITE 37.5W @ 24VAC WHITE WHITE 37.5W @ 24VAC WHITE WHITE 37.5W DEFROSTER 24VAC CAP WHITE FAN DIODE BRIDGE 11 12 13 14 15 16 17 8 9 10 54 32 1 LENS RED BLK PCB9000255A 21 22 23 24 25 26 27 28 29 30 18 19 20 1 2 34 5 6 7 INPUT VAC INPUT WIRING DIAGRAM AC HIGH AC NEUTRAL GROUND WHITE 37.5W @ 24VAC WHITE WHITE 37.5W @ 24VAC WHITE CAP WHITE 37.
4.2 INSTALLATION OF CAMERA/LENS 4. To install the camera/lens, perform the following steps: 1. Open the lid by releasing the two latches at the rear of the enclosure. The gas springs will securely hold the lid in place when fully opened. If necessary, the lid can be removed. 2. Remove the camera sled from the rail by loosening the two Phillips head screws and sliding the sled to the rear. Attach the camera/lens with the 1/4-20 Phillips head screws provided.
4.3 ENCLOSURE MOUNTING - PAN/TILT 3. The EH6500 Series Enclosure can be mounted to a pan/ tilt assembly in addition to a wall or pedestal/ceiling mount. Secure the mount to a suitable load bearing surface. Use fasteners with a minimum 1/4-inch diameter. 4. Attach the pan/tilt to the mount. The pan/tilt control connector should be positioned towards the building/mounting location. Note the “front” label on the pan/tilt. 5. Install the camera/lens according to the instructions in paragraph 4.
4.4 SUN SHROUD ASSEMBLY INSTALLATION (OPTIONAL) The sun shroud provides air space between the sun shroud and the enclosure to protect from direct rays of the sun and reduces the internal temperature approximately 10-15°F (6°-10°C). NOTE: Use the six (6) 10-32 x .375 Phillips head screws and nylon washers from the enclosure assembly. 4.
5.0 CARE AND MAINTENANCE a. Maintenance performed at regularly scheduled intervals will help prolong the operational life and appearance of the equipment. Remove the two Phillips head screw and pull the filter assembly out of the enclosure for access to the filter. b. Remove the wire screen and filter pad. Clean the pad with water and mild detergent, dry thoroughly, and reinsert or replace with a new pad. (Replacement pads, part number EH550010045, are available from Pelco.) 1.
7.0 WW6500 MECHANICAL PARTS LIST Item Qty 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Not Shown 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 3 1 3 1 1 1 1 1 1 2 1 1 51 4 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 3 1 1 4 4 2 8 4 4 2 1 10 Description Bearing Diode, full brdg. rect.
8.0 MODELS EH6500-1 Enclosure, Environmental with 120V Heater and Blower EH6500-2 Same as EH6500-1, except 24V EH6500-3 Same as EH6500-1, except 230V 8.1 OPTIONAL ACCESSORIES FACTORY INSTALLED WW6500 WW6500/220 WD6500 WD6500/220 TI6500 LK6500 Window wiper, 120 VAC Window wiper, 230 VAC Window defroster, 120 VAC, 75 vA Window defroster, 230 VAC Thermal insulation Tamper resistant lock kit for EH6500 Series 8.
10.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one (1) year after the date of shipment. Exceptions to this warranty are as noted below: • Two (2) years on all standard motorized and fixed focal length lenses. • Two (2) years on Legacy®, Intercept®, CM6700/ CM8500/CM9500/CM9750/CM9760 Matrix, Spectra™, DF5 Series and DF8 Fixed Dome products.