® EH8000 Series Pressurized Camera Enclosures Installation/ Operation Manual C418M (8/97) Pelco • 300 W.
TABLE OF CONTENTS Section Page 1.0 SCOPE .............................................................................................................................................. 1 1.1 WARNINGS ............................................................................................................................. 1 2.0 DESCRIPTION .................................................................................................................................. 1 2.1 MODEL NUMBERS .............
INSTALLATION/OPERATION MANUAL MODEL EH8000 SERIES PRESSURIZED CAMERA ENCLOSURES CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. 4. Only use replacement parts recommended by Pelco. 1.0 SCOPE The information contained within this manual covers the installation and operation of the EH8004, EH8006, EH8006-26, and the EH8008 environmental enclosures. 1.1 WARNINGS 5.
2.1 MODEL NUMBERS EH8004 EH8006 EH8006-26 EH8008 4" (10.16 cm) diameter, 17" (43.18 cm) long pressurized camera enclosure with lens preset capabilities. Provided with one (1), 40 watt heater. 6" (15.24 cm) diameter, 20" (50.80 cm) long pressurized camera enclosure with lens preset capabilities. Provided with two (2), 80 watt heaters. 6" (15.24 cm) diameter, 26" (66.04 cm) long pressurized camera enclosure with lens preset capabilities. Provided with two (2), 80 watt heaters. 8" (20.
3.0 SPECIFICATIONS ELECTRICAL Input Voltage: 120 VAC (230 VAC optional) for heaters Power Requirements: 40 watts (EH8004) 160 watts (all other models) Connector: Mating Connector: Maximum Camera/Lens Size: EH8004 3.75" (9.53 cm) diameter x 14" (35.56 cm) long or 14"L x 2.8"W x 2.8"H (35.56 cm x 7.11 cm x 7.
Sand and Dust: MIL-E-5400T, para. 3.2.24.7. 4.1 ENCLOSURE MOUNTING — FIXED Fungus: MIL-E-5400T, para. 3.2.24.8. The enclosure can be mounted to either a wall mount or a ceiling/pedestal mount. Salt Atmosphere: MIL-E-5400T, para. 3.2.24.9. Explosion: For proper mounting, refer to the mounting instructions accompanying the specific mount you are using. MIL-E-5400T, para. 3.2.24.10. (Design and product specifications subject to change without notice.
4.2 ENCLOSURE MOUNTING — PAN/TILT The enclosure can be mounted to a pan/tilt which is mounted to a wall or ceiling. For proper mounting, refer to the mounting instructions accompanying the specific mount and pan/tilt you are using. To insure suitable load bearing, a minimum of 1/4-inch (0.63 cm) diameter fasteners should be used to secure the mount and/or pan/tilt to the mounting surface. The enclosure should be attached to the mount/ pan/tilt by a minimum of two 1/4-20 fasteners.
4.3 CAMERA/LENS INSTALLATION AND ADJUSTMENTS To install the camera/lens combination, perform the following steps: 1. Disassemble the enclosure as specified in the Maintenance Section, Section 7.0. CAUTION Pressure must be released prior to opening the enclosure or personal injury may result. 2. Install the camera/lens on the camera sled (Figure 10, item 11) by screwing the camera to the sled. 3.
Figure 6.
Figure 7.
Figure 8.
4.5 SUN SHROUD INSTALLATION 5.1 SYSTEM TEST The sun shroud provides an air space between itself and the enclosure to protect the enclosure from the direct rays of the sun and reduces the internal temperature of the enclosure approximately 10-15° F (-12.22°-9.44° C). 1. Power up the camera. To install the sun shroud, perform the following steps (see Figure 9): 6.0 TROUBLESHOOTING GUIDELINES 1. Insert the mounting straps through the holes in the standoffs inside the shroud. 2. Align the sun shroud. 3.
CAUTION: Pressure must be released prior to opening the enclosure or personal injury may result. 5. Once the internal pressure has been relieved, use a screwdriver to pry the end of the spiral retaining ring (Figure 10, item 5) from the retaining ring groove in the enclosure body. 6. Next, pull on the “T” handle to remove rear plate from housing.
8.0 EXPLODED ASSEMBLY DIAGRAM Figure 10. EH8000 Series Enclosures Exploded Assembly Diagram 9.0 EH8000 SERIES ENCLOSURES MECHANICAL PARTS LIST The following parts lists correspond to Figure 10. EH8004 MECHANICAL PARTS LIST Item No. Qty 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 1 2 1 1 2 1 1 3 1 1 1 1 1 1 1 1 2 1 1 2 4 6 12 Description Connector, solder receptacle jam nut Strap, cradle Cradle enclosure Glass, 4.105" diameter x .
EH8006, EH8006-26 MECHANICAL PARTS LIST Item No. Qty. Description 1 1 Connector, solder receptacle jam nut 2 2 Strap, cradle 3 1 Cradle enclosure 4 1 Glass, 6.100" diameter x .225" 5 2 Ring, retaining, spiral SS 6 1 Valve, tank, Schraeder 9466-L8 7 1 Bag, Desiccant 8 3 “O” RING 9 1 Valve, pressure relief 10 1 Body assembly 11 1 Camera sled 12 1 Rear plate 13 1 Sealing ring, window 14 1 Elevation block 15 1 Camera sled spacer 16 1 Terminal block jumper 17 3 Terminal block, 4-position 18 1 Screw, 1/4-20 x .
11.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one (1) year after the date of shipment. Exceptions to this warranty are as noted below: If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information: 1. Model and serial number 2. Date of shipment, P.O.
