Spec Sheet

Pelco by Schneider Electric
3500 Pelco Way, Clovis, California 93612-5699 United States
USA & Canada Tel [phone] Fax [phone]
International Tel [phone] Fax [phone]
www.pelco.com
TECHNICAL SPECIFICATIONS
MODELS
EH8104-1 Pressurized enclosure with two 120 VAC
heaters; 10.16 cm (4-inch) inside diameter
EH8104-3 Pressurized enclosure with two 230 VAC
heaters; 10.16 cm (4-inch) inside diameter
EH8106-1* Pressurized enclosure with two 120 VAC
heaters; 15.24 cm (6-inch) inside diameter
EH8106-3* Pressurized enclosure with two 230 VAC
heaters; 15.24 cm (6-inch) inside diameter
ELECTRICAL
Input Voltage
EH8104-1, EH8106-1 120 VAC
EH8104-3, EH8106-3 230 VAC
Power Consumption
EH8104 Series 40 W
EH8106 Series 80 W
Heater
EH8104-1 2 at 20 W each, 120 VAC
EH8104-3 2 at 20 W each, 230 VAC
EH8106-1 2 at 40 W each, 120 VAC
EH8106-3 2 at 40 W each, 230 VAC
Heater(s) are thermostatically controlled to
activate at 4°C (40°F) and turn off at
15°C (60°F)
Connector 16-pin receptacle with jam nut
Mating Connector MS-type connector (supplied)
Maximum Cable Distances
120 VAC EH8104 Series EH8106 Series
16 AWG (1.5 mm
2
) 1,365 m (4,477 ft) 682 m (2,238 ft)
18 AWG (1.0 mm
2
) 860 m (2,821 ft) 430 m (1,410 ft)
20 AWG (0.5 mm
2
) 540 m (1,773 ft) 270 m (886 ft)
230 VAC
16 AWG (1.5 mm
2
) 15,014 m (16,449 ft) 2,507 m (8,224 ft)
18 AWG (1.0 mm
2
) 3,159 m (10,364 ft) 1,579 m (5,182 ft)
20 AWG (0.5 mm
2
) 1,985 m (6,514 ft) 993 m (3,257 ft)
MECHANICAL
Front Window
EH8104 Series 4-inch diameter tempered glass, 0.225-inch
thick
EH8106 Series 6-inch diameter tempered glass, 0.225-inch
thick
Camera Mounting Multiple mounting holes on camera sled
allow for linear adjustment
Maximum Camera
and Lens Size Accepts camera and lens combinations
†
(including BNC connector) up to:
EH8104 35.56 x 6.35 x 6.35 cm
(14.00" L x 2.50" W x 2.50" H) or
35.56 x 7.62 cm (14.00" L x 3.00" diameter)
EH8106 45.72 x 10.16 x 10.16 cm
(18.00" L x 4.00" W x 4.00" H) or
45.72 x 12.7 cm (18.00" L x 5.00" diameter)
Enclosure Mounting Adjustable cradle secured with type 316
stainless steel bands
Purge Fitting Standard Schrader valve to allow enclosure to
be filled with dry nitrogen
Purge Relief Fitting Prevents over pressurization of enclosure
GENERAL
Construction Aluminum 6061 T6
Finish Gray polyester powder coat
Weight Unit Shipping
EH8104 Series 3.62 kg (8 lb) 4.98 kg (11 lb)
EH8106 Series 6.79 kg (15 lb) 8.15 kg (18 lb)
ENVIRONMENTAL
Ambient Operating
Temperature -40° to 50°C (-40° to 122°F) with heater(s)
Vibration 5 to 60 Hz with 0.082-inch total travel (15 g at
60 Hz). From 60 to 1,000 Hz, 5 g RMS with
random vibration
Altitude Sea level to equivalent of 3,048 m (10,000 ft)
Acoustic Noise Operates in 150 dB acoustic noise
environments
Humidity Up to 100% relative humidity; standard
Schrader and pressure relief valves provide
positive internal pressure with dry nitrogen
CERTIFICATIONS/RATINGS
•CE
• UL/cUL Listed
• Meets NEMA Type 6 and IP67 standards
OPTIONAL ACCESSORIES
Sun Shroud SS8004 Sun shroud for EH8104 Series enclosure
SS8006 Sun shroud for EH8106 Series enclosure
Other EH8000RKIT Dry nitrogen recharging kit (nonrefillable)
PSKIT8100 Pressure sensor kit; provides a contact closure
that can be wired to trigger an alarm when
internal pressure drops to 2 psi
RECOMMENDED MOUNTS
EH8104 Series
EM1109, EM2000, EM2200 Medium duty mount for horizontal/vertical
pipe or pole; maximum load is 18.1 kg (40 lb)
EM22 Medium duty wall mount; maximum load is
18.1 kg (40 lb)
MM22 Medium duty ceiling/pedestal mount;
maximum load is 18.1 kg (40 lb)
EH8106 Series
PM2000, PM2010
‡
Pedestal/ceiling mount; maximum load is
56.62 kg (125 lb)
WM2000
‡
Wall mount; maximum load is 34 kg (75 lb);
increased to 68 kg (150 lb) when used with
ST1 strut
WM3026 Heavy duty wall mount with adjustable head;
maximum load is 136 kg (300 lb)
Adapters
AH2000 Adjustable head
STI Support strut
RECOMMENDED PAN/TILTS
PT570 Series Medium duty pan/tilt; maximum load is
18.14 kg (40 lb)
*For applications requiring an integrated positioning system, refer to our
Pressurized Legacy Series.
†
Assumes lens is fully extended.
‡
Use with AH2000 adjustable head.
Pelco, the Pelco logo, and other trademarks associated with Pelco products referred
to in this publication are trademarks of Pelco, Inc. or its affiliates. All other
product names and services are the property of their respective companies.
Product specifications and availability are subject to change without notice.
©Copyright 2011, Pelco, Inc. All rights reserved.