I N S T A L L A T I O N Endura™ KBD5000 Series Keyboard C1620M-B (9/05)
Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Parts List . . . . . . . . . . . . . . . . . . . . . . . .
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules.
Description The KBD5000 Series keyboard is the controller for Pelco’s network-based video system products. It is the point from which all user functions can be accessed. The KBD5000 Series is configured with three control modules that are installed in receptacles on the keyboard base. Modules can be placed into any receptacle, creating a customized keyboard for operation with either the left or right hand.
PACKAGE CONTENTS When installing the KBD5000, refer to Figure 1. ACCESSORY PACK JOG/SHUTTLE MODULE 1 EA. KEYBOARD BASE 1 EA. KEYPAD MODULE 1 EA. POWER SUPPLY AND USB CABLE 1 EA. USA STANDARD POWER CORD (110 VAC) 1 EA. SECURITY BIT 1 EA. EUROPEAN STANDARD POWER CORD (220 VAC) 1 EA. WRIST SUPPORT 1 EA. SHOWN ACTUAL SIZE PHILLIPS PAN HEAD SCREW 4-40 X .312-INCH 4 EA. BUTTON HEAD SCREW 10-32 3/8-INCH 3 EA. JOYSTICK MODULE 1 EA.
Rear Panel Connectors Figure 3. Rear Panel Connectors Input power USB Type A port USB Type B port (Attaches to a VCD5000 or Endura Workstation [WS5000 Series]; use the supplied Type B-to-Type A adapter cable.) Headphone connector/speaker Microphone connector NOTES: • Any USB cable attached to the keyboard must be no longer than 16.4 feet (5.0 m). • You can use the USB ports to export video, clips, or still images.
Installation INSTALLING THE WRIST SUPPORT AND CONTROL MODULES The KBD5000 comes with three control modules that fit in three receptacles on the base. You can choose which module will be located in which receptacle, and each module can be rotated ±60 degrees in each receptacle. The KBD5000 also has a wrist support that can be easily installed and removed. This system allows custom tailoring of the keyboard to your preferences.
3. Refer to Figure 5. Select a module. Each receptacle on the base has an attached USB cable. Turn the module upside down. Plug the USB connector cable into the USB port on the bottom of the module. Thread the USB connector cable through the plastic strain reliefs on the module to hold the cable in place. Figure 5. Installing the Modules 4. Refer to Figure 5. Turn the module upright so its top faces the rear of the base. (The rear of the base is the side with the connectors.
CONNECTING THE KEYBOARD To hook up the KBD5000, connect the USB Type B-to-Type A cable (supplied) from the USB connector on the rear of the KBD5000 to the USB connector on either the front or rear of the Pelco VCD5000 virtual console display or to the USB connector on an Endura Workstation (WS5000 Series). (As an example, Figure 6 shows a connection to either the rear or front of a VCD5000.) NOTE: Any USB cable attached to the keyboard must be no longer than 16.4 feet (5.0 m).
Operation The following is only a simple guide. For details on operating the KBD5000, refer to the Pelco VCD5000 Virtual Console Display Operation manual, C1618M. KEYS The callouts in Figure 7 correspond to the reference numbers in Table A. Figure 7. Keyboard Keys Table A.
OVERVIEW OF VCD5000 MENUS The KBD5000 works in conjunction with the VCD5000 virtual console display and its menus. • To display the on-screen menu, press either Menu key on the jog/shuttle module. • To hide the menu, press either Menu key on the jog/shuttle module. • There are two ways to navigate within a menu and select an item. (1) Joystick Use the joystick to navigate within a menu and click the button atop the joystick to select an item.
Troubleshooting If the following instructions fail to solve your problem, contact Pelco Technical Support for help at 1-800-289-9100, or 1-559-292-1981 if calling internationally. You should have the serial number from the bottom of the keyboard ready in case it is needed. Do not try to repair a keyboard yourself. Opening it immediately voids any warranty. Leave maintenance and repairs to qualified technical personnel. Swap a defective unit with a replacement unit and return the defective one for repair.
Specifications POWER SUPPLY Input Voltage 100-240 VAC, 50/60 Hz Output Voltage 12 VDC Power Output 20 W Input Connector Type Universal, interchangeable Output Connector Type 2.5 mm screw-on barrel Cable Type Supplied with grounded power cord; molded connector, 3 prongs, 6 ft (1.8 m); 1 USA standard (110 VAC), 1 European standard (220 VAC), 1 UK standard (250 VAC) KEYBOARD BASE Keyboard Interface USB 2.0 Cable USB, captive, 16.4 ft (5.0 m) Input Voltage 12 VDC Input Current 1.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. • Three years on Genex ® Series products (multiplexers, server, and keyboard). If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information: 1. Model and serial number 2.
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.
