I N S T A L L A T I O N EU3512-3X Environmental Enclosure and Light Duty Wall Mount C2428M-B (1/06)
Important Safety Instructions Prior to installation and use of this product, the following WARNINGS should be observed. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Only use attachments/accessories specified by the manufacturer. 6. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
Description The EU3512-3X is an indoor/outdoor light-duty camera enclosure and light-duty wall mount. The enclosure includes a sun shroud and 230 VAC heater and defroster. The wall mount has an adjustable tilt table allowing for mechanical positioning of the enclosure. Install the EU3512-3X to any wall or vertical surface capable of supporting up to 20 lbs (9 kg).
Installation INSTALL WALL MOUNT 1. Drill holes in mounting surface using the mount as a template and attach the mount securely with the recommended fasteners. • • If you are attaching the mount to a solid surface, use the two top outside holes and the bottom center hole. Secure with three 0.25-inch diameter fasteners (not supplied). If you are attaching the mount to a wall stud, use the top and bottom center fastener holes. Secure with one 0.3125-inch fastener and one 0.25-inch fastener (not supplied). 2.
CAMERA AND LENS INSTALLATION 1. To install the camera and lens onto the enclosure sled: a. Extend the lens to the maximum length. b. Position the camera and lens so that they do not extend beyond the track. c. Fasten the camera and lens to the sled with the two, 1/4-20 x 0.375 Phillips screws (supplied). The edges of the sled are bent, one side up and the other side down. One side of the sled has a wide lip and the other side has a narrow lip.
INPUT, AC HIGH INPUT, AC LOW (NEUTRAL) 1 2 3 4 5 6 7 8 9 10 DEFROSTER HEATER Figure 1. Wiring Diagram Table A. Heater and Defroster Wiring Distances The following cable sizes are the minimum recommended for use with the heater and defroster. WARNING: When using a single power source for both camera and accessories, consider the camera power consumption when determining the wire gauge. C2428M-B (1/06) Input Voltage Power Consumption 230 VAC at 50 Hz 43 watts Cable Size Cable Distance 20 AWG (0.
Table B. 24 VAC Wiring Distances The following are the recommended maximum distances for 24 VAC applications and are calculated with a 10 percent voltage drop. (Ten percent is generally the maximum allowable voltage drop for AC-powered devices.) Wire Gauge Total VA 20 AWG (0.5 mm2) 18 AWG (1.0 mm2) 16 AWG (1.5 mm2) 14 AWG (2.
Specifications ENCLOSURE Camera Mounting Multiple holes on adjustable camera sled; camera sled mounts in threaded strip for easier removal and can be inverted for additional camera elevation Camera and Lens Size Accommodates camera and lens combinations (including BNC connector) 2.87” W x 3.00” H x 9.00” L (7.28 x 7.62 x 22.86 cm) Viewing Window Lexan®, 0.187-inch (4.75 mm) thick, optically clear, impact-resistant, MR5 coated (U.L. 94HB rated) Viewing Area 2.25” H x 2.63” W (5.71 x 6.
5.1 (13.0) 14.75 (37.47) 3.8 (9.86) 11.25 (28.57) 12.75 (32.38) 2.0 (5.08) NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE IN INCHES. Figure 2. Enclosure Dimension Drawing 2.00 (5.08) Ø 0.272 (0.69), 3X 3.28 (8.33) 1.64 (4.17) 1.40 (3.56) 2.80 (7.11) 1.50 (3.81) 11.08 (28.14) 2.75 (6.99) 2.95 (7.49) 2.86 (7.26) Ø 0.281 (0.713), 3X 5.43 (13.79) 3.48 (8.84) Ø 0.343 (0.87), 1X 1.25 (3.18) 10.53 (26.75) NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE IN INCHES.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex® Series products (multiplexers, server, and keyboard).
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.