O P E R AT I O N / P R O G R A M M I N G ® ExSite Series Explosionproof Positioning System C1300M-C (11/08)
Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enable Motion Detection (23X Day/Night Camera) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Edit Detection Areas (23X Day/Night Camera) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules.
Welcome Thank you for purchasing Pelco’s ExSite™ IPSXM Series explosionproof positioning system. Your new system features a high resolution, camera/optics package with programmable software. This manual is designed to be a reference tool for the operation and programming of your system. Inside you will find information about the features and commands of your IPSXM system, as well as a detailed menu tree.
How to Operate Your System Operation How to Control Pan and Tilt Move joystick or press the direction keys left/right and up/down. Zoom Far To zoom far, do the following: 1. Press the Zoom Tele button or turn the joystick clockwise until zoom stops at the 32X zoom limit. 2. Release the button or joystick for one second. 3. To continue zooming (digitally), press the button or turn the joystick clockwise again until you have the picture you want or reach the digital zoom* limit.
ACCESSING MAIN MENU (PRESET 95) You can call up the main menu on your monitor by programming (setting or creating) preset 95 (preset 28 if in AD32-preset mode). Programming preset 95 for Pelco’s controllers varies according to the type of controller you are using. Instructions for programming preset 95 are given below for various Pelco controllers. CM6700/CM6800 1. 2. 3. Enter the number of the IPSXM system and press the CAM key. Enter 95 and hold the PRESET key for two seconds.
Quick Start Guide: System Setup PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION Access the main menu (preset 95). See the Accessing Main Menu (Preset 95) section.
C1300M-C (11/08)
Language PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM EXIT ENGLISH OFF The language for the on-screen menus is selectable. Available languages include English, Spanish, French, German, Italian, Portuguese, Polish, Russian, Turkish, and Czechoslovakian. The factory default language is English. To change the display language: 1. Use the joystick to position the cursor beside LANGUAGE. 2.
Unit Inversion PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF Unit inversion reconfigures the system so that it operates normally when it is installed in an inverted postion. The following are the available settings for unit inversion. OFF (default) Use for normal installations (refer to Figure 1).
System Information PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF The system Information screen displays ExSite model, software version, available memory, and other diagnostic information. System settings cannot be changed using this screen. This screen is for reference only. Use the following steps to display the System Information screen: 1. 2.
Display Setup PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM Display setup allows you to program how labels are displayed on the monitor. The following labels are available: PRESET LABEL Identifies preset. ZONE LABEL Identifies zone. ZOOM Identifies the amount of magnification. AZIMUTH*/ ELEVATION** Amount of pan from 0° and the amount of tilt from 0° horizontal.
LABEL POSITIONS PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF Labels can be placed anywhere on the monitor. This feature allows you to customize the appearance of your monitor screen. The following labels are not set at fixed positions: Preset Label Zone Label Alarm 1 Azimuth*/Elevation**: XXX°/-XX° Zoom Ratio: XXX.XX Direction: Compass direction is shown.
Unit Settings CAMERA TYPE OF LIGHTING PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF Pelco has calibrated settings that optimize the white balance, and the picture, for multiple lighting conditions; settings differ depending upon the model. There are two types of lighting settings for 22X models: T1 (default) T2 RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM For use in outdoor applications.
IR CUT FILTER (23X DAY/NIGHT CAMERA) PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF ExSite IPSXM has two modes of operation: color and black-white. You can increase sensitivity in low light conditions by switching to black-white mode (removing the IR cut filter). Color mode is preferred in normal lighting conditions.
ADVANCED CAMERA SETTINGS SHUTTER SPEED PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM Shutter speed is the duration of the electronic shutter. Program shutter speed to operate automatically (Auto) or manually (Numeric Value). AUTO (default) The electronic shutter speed is set automatically by the amount of light sensed by the camera.
AUTO IRIS PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF Auto iris is the lens function that automatically opens and closes the iris in response to changing light conditions. Program the auto iris to operate automatically or at a user-defined level. RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM OFF Auto iris is disabled, and control is always manual.
BACKLIGHT COMPENSATION (BLC) PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF If a bright backlight is present, the subjects in the picture may appear dark or as a silhouette. Backlight compensation enhances objects in the center of the picture. The system uses the center of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash out to white.
MOTION PROPORTIONAL PAN PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the amount of zoom. At telephoto zoom settings, the pan and tilt speeds will be slower for a given amount of joystick deflection than at wide zoom settings. This keeps the image from moving too fast on the monitor when there is a large amount of zoom.
PARK TIME PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF This feature allows the system to begin a specified operation (scan, preset, or pattern) after a programmed time of inactivity. Park time can be programmed from 1 minute to 720 minutes (12 hours), or set to zero, which disables this feature. The default setting is zero.
SCAN SPEED PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF Scan speed is the degrees per second that the system will pan when in scan mode. Scan speed is adjustable from 1 to 40 degrees per second through the programming menu. The default setting is 25 degrees per second. PRESET FREEZE FRAME RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM This feature freezes the scene on the monitor when going to a preset.
LIMIT STOPS PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF Limit stops are programmable stops that limit the pan range of the unit. There must be two limits, a left and a right, to define an area. There are two types of limit stops: RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM MANUAL A manual (joystick) pan operation stops when a limit stop is reached.
AZIMUTH ZERO PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF Azimuth is the pan angle from 0 to 359 degrees. Azimuth zero is the pan position you specify to be the 0-degree point. Azimuth zero is normally set to magnetic north. Once set, azimuth and compass readings are based on the set Azimuth Zero point. To program azimuth zero: RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM 1. 2. 3.
POWER UP POWER UP ACTION PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF This setting defines a specific activity (scan, preset, pattern) to be performed in the event the power to the system is cycled.
LINE SYNC PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF Line sync refers to a programmable function that allows you to synchronize all cameras within a matrix system. NOTE: ExSite IPSXM automatically senses V-Sync input. No line sync setup is required for Pelco control systems that provide a V-Sync signal.
PRESETS PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF The ExSite IPSXM system has 80 programmable preset positions. Each preset can be programmed to use pan, tilt, all programmable camera settings, and motion detection. The presets are numbered 1-32 and 35-82. Presets 33 and 34 are fixed commands that cannot be programmed. Preset 33 is disabled in the ExSite IPSXM.
ENABLE MOTION DETECTION (23X DAY/NIGHT CAMERA) PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM The following are the settings for MOTION DETECTION ENABLED: OFF (default) Motion detection is turned off (disabled). ON Motion detection is turned on (enabled). NOTE: Motion detection does not work if the shutter speed is set at less than 1/60 of a second.
ACTIVATE AUX COMMAND (23X DAY/NIGHT CAMERA) PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM Motion detection can be programmed to trigger an auxiliary command when motion is detected. The following are the settings for ACTIVATE AUX: OFF (default) Motion detection will not trigger an AUX command. 1 Triggers a command to AUX 1. 2 Triggers a command to AUX 2.
PATTERNS PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF A pattern is a memorized, repeating, series of pan, tilt, zoom and preset functions that can be recalled with a command from a controller or automatically by a programmed function (alarm, park or power-up). The ExSite IPSXM can handle up to four user-defined patterns. Pattern length is based upon memory usage rather than a fixed amount of time.
ZONES A zone is a pan area, defined by a left and right limit, on the 360-degree pan plane. The IPSXM positioning system is capable of eight zones, each with a 20-character label. PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF To program a zone: 1. Use the joystick to position the cursor beside ZONE NUMBER. Press Iris Open the cursor moves to the right. RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM 2.
WINDOW BLANKING PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF Window blanking allows a user to program up to eight, four-sided, user-defined areas that cannot be viewed by the operator of the system. A blanked area will move with pan and tilt functions and automatically adjust in size as the lens zooms telephoto and wide. ExSite IPSXM has two style modes for window blanking, GRAY and SMEAR. If style is set to gray, the blanked area is covered with a solid gray window.
REVERSE PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF A blanked out area can be reversed to make it visible and the areas on both sides of it not visible. The areas above and below the blanking area remain visible. Reversing the window a second time will return it to its original condition. CLEAR WINDOW RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM All areas that have been set for window blanking are cleared.
ALARMS PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF The ExSite IPSXM system has seven alarm inputs, which can be programmed as high, medium or low priority. When an alarm is received, an input signal to the unit triggers the user-defined action (go to preset, run pattern, etc.) programmed for the alarm.
3. PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF Select the alarm priority: a. Use the joystick to position the cursor beside ALARM PRIORITY. b. Press Iris Open. The cursor moves to the right. c. Move the joystick up or down to view the available selections. Available settings include HIGH, MEDIUM, and LOW (default).
5. PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF Set the auxiliary to activate: a. Use the joystick to position the cursor beside ACTIVATE AUX. b. Press Iris Open. The cursor moves to the right. c. Move the joystick up or down to view the following available selections. RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM NO (default) Not activated. 1 An alarm action will activate AUX 1.
WIPER The following IPSXM unit models feature a window wiper to clear moisture from the window of the enclosure: PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF IPSXM31C22-2 IPSXM31C22-2X IPSXM31CBW23-2 IPSXM31CBW23-7 IPSXM31C22-7 IPSXM31C22-7X IPSXM31CBW23-2X IPSXM31CBW23-7X NOTE: The Wiper menu is available only on the above models. To check the unit model, refer to the System Information section of this manual.
SET WASHER SEQUENCE An external washer (not supplied by Pelco) can be used to wash the window of the enclosure. Accessing AUX 3 or selecting Preset 87 will start the washer sequence. PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF Use the following steps to program the washer sequence. 1. Use the joystick to position the cursor beside WIPER and then press Iris Open. The wiper menu appears on the monitor.
AUX An auxiliary output is a programmable signal from the system that can trigger another device to operate. An auxiliary output is programmable to trigger from an alarm or from a controller. PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF An AUX 1 command from the controller will activate the relay in the system and operate the device that is connected to the relay.
CLEAR Use this setting to clear user-defined settings or return the system to factory default settings. PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM EXIT The following are the available CLEAR settings: ALL ZONES Clears all zones. To clear a single zone, refer to the Zones section. ALL PRESETS Clears all presets. To clear a single preset, refer to the Presets section.
PASSWORD PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF ExSite IPSXM features password protection to prevent unauthorized changes to the system settings. An operator can open the System Information and Display Setup Screens, but cannot access any of the Unit Settings menus. Controller/keyboard commands cannot override password-protected settings. If a keyboard is used to set a preset, pattern, or zone, the Enter Password screen appears on the monitor.
Position Calibration PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION ENGLISH OFF RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM EXIT POSITION CALIBRATION *** PRESET NOT DEFINED *** BACK EXIT REFERENCE INFORMATION AZIMUTH ELEVATION ZOOM Position calibration sets the preset reference point for all automatic positioning system movements.
Reset, Cycle Power, Reboot RESET CAMERA PELCO EXSITE IPSXM LANGUAGE UNIT INVERSION RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM ENGLISH OFF Use this function to reset all camera settings to factory default parameters. NOTE: Reset camera restores all camera settings, except those associated with presets. CYCLE CAMERA POWER If the camera is not operating or if you lose camera control, cycle camera power.
Software/Language File Upload The ExSite IPSXM system allows access for on-site setup, testing, and uploading of revised operating software and language files. A Pelco field service tool is required to perform these operations. Field service tools include Pelco’s remote monitor kit (IPS-RMK), remote data port box (IPS-RDPE-2), and remote monitor cable (IPS-CABLE).
Specifications Day/Night (23X) Color NTSC, PAL 2:1 interlace 1/4-inch progressive scan CCD LowLight™ (22X) Color NTSC, PAL 2:1 Interlace 1/4-inch EXview HAD™ CCD NTSC 768 (H) x 494 (V) 768 (H) x 494 (V) PAL 752 (H) x 582 (V) 752 (H) x 582 (V) NTSC 540 TV lines >470 TV lines PAL 540 TV lines >460 TV lines f/1.6 (focal length, 3.6~82.8 mm optical) 23X optical, 10X digital 2.9/4.2/5.8 seconds 54° at 3.6 mm wide zoom 2.5° at 82.8 mm telephoto zoom Automatic with manual override f/1.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
www.pelco.com Pelco, Inc.