I N S T A L L A T I O N EPS5000-120 External Power Supply For Fiber Optic Modules C1632M-A (10/06)
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules.
Description The EPS5000-120 external power supply, which is 1 rack unit (RU) high, has dual 120 W power supplies that slide into a tray. The external power supply can be mounted into a 19-inch, EIA-standard rack.
BACK VIEW Power Switch (2) AC Power Cord Connector (2) 6-Pin Power Connector (2) Relay Output Connector (2) Spare Fuse (2) Figure 2.
Installation The following items are supplied with each EPS5000-120. 1 Rack mount chassis 2 Snap-on ferrites 2 Power supplies (EPSPWR-120) 4 Power cords (2 USA standard and 2 European standard) 2 G-power cables (over-molded) 4 Screws, 10-32 x 0.750-inch, Phillips, pan head with washers ATTACHING THE FERRITES Two snap-on ferrites are supplied with the EPS5000-120 external power supply, one for each over-molded cable.
Figure 3. Mounting an EPS5000-120 into a Rack EPS5000-120 POWER CORD POWER CORD OVER-MOLDED CABLE RK5000-3U OVER-MOLDED CABLE RK5000PS-3U Figure 4.
Service REPLACING A POWER SUPPLY You can easily replace either of the two power supplies in the EPS5000-120 in case of failure. The power fail LED on the front of each power supply turns red if there is a problem with the power supply. The blue Pelco badge will turn off if one of the power supplies fails. Before replacing a power supply, check the fuse. It can be replaced easily with the supplied spare.
Specifications ELECTRICAL Input Voltage 100-240 VAC Input Current 3.2 A total Output Voltage 12 VDC per power supply Output Current 10 A per power supply Fuse Rating 1.6 A per power supply Relay Rating 1 A, 40 VDC MECHANICAL Rack Units 1 Construction Aluminum Finish Black GENERAL 10 Operating Temperature 32° to 122°F (0° to 50°C) Operating Humidity 80% maximum relative humidity, noncondensing Dimensions 1.73" H x 17.40" W x 12.00" D (4.39 x 44.20 x 30.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted pair transmission products. • Three years on Spectra® IV products. • Three years on Genex® Series products (multiplexers, server, and keyboard).
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.