FD1 Series 540 TV lines High Resolution Camera Installation/Operation Manual (FD1-F Series) (FD1-IR Series) C3909M-EN (03/12) Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
CONTENTS Important Safety Instructions ........................................................................................................................ 3 Troubleshooting Tips ..................................................................................................................................... 4 Regulatory Notices ........................................................................................................................................ 5 1. Introduction....................
Important Safeguards and Warnings Important Safety Instructions 1. Read Instructions. All the safety and operating instructions should be read before the camera is operated. 2. Retain Instructions. The safety and operating instructions should be retained for future reference. 3. Heed Warnings. All warnings on the camera and in the operating instructions should be adhered to. 4. Follow Instructions. All operating and use instructions should be followed. 5.
Important Safeguards and Warnings a. When the power supply cord or plug is damaged. b. If liquid has been spilled or objects have fallen into the camera. c. If the camera has been exposed to rain or water. d. If the camera does not operate normally by following the operating instructions.
Important Notices Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules.
1. Introduction Introduction INTRODUCTIO The dome camera series are ideal for indoor installation in commercial environment. With 2 or 3-axis mount support, it provides flexible installation: 2 axis mounts on ceilings only and 3 axis mounts on a ceiling or wall even at an angle. 1.1 Package Contents Check that the items received match those listed on the order form and packing slip.
Introduction INTRODUCTIO Figure 1-2 FD1-IRF4(X)/FD1-IRV9(X) (typical) 1.
Introduction INTRODUCTIO Figure 1-4 FD1-IRF4 1. FD1-F series: Cable Y used for surface run power/video connector Figure 1-5 FD1-IRV9 5. Zoom lever FD1-IR series: Conduit hole used for surface run power/video connector 6. Focus lever 2. Bottom case A. Video Output Terminal 3. Camera housing B. DC12V Power Connector ( Red+/Black- ) 4. Dome cover Note: See Figure 2-3 for camera board controls. 1.4 Routine Maintenance • The dome cover is an optical part.
Installation OSD Setup Menu 2. Installation Section 2(A) is installation for FD1-F Series. 2.1(A) Inserting Screw Anchors 1. Mark hole positions on the desired location. 2. Drill 2 holes according the two fixing holes in camera bottom case and insert screw anchors provided. Figure 2-1(A) Insert Screw Anchors 2.2(A) Connecting the Wiring Refer to Figure 1-3 to connect the video connect output connector (A) and DC12V power connector (B).
Installation OSD Setup Menu Figure 2-2(A) Camera Installation 2.4(A) Adjusting the Camera Position The dome camera has two axes for positioning the camera. While monitoring the picture on the monitor, adjust the camera position as follows: • Pan Adjustment: Rotate 3D assembly in the base. Do not turn assembly more than 360°as this may cause the internal cables to twist and disconnect or break.
Installation OSD Setup Menu 2.5(A) Locking (fixing) the Camera Body Adjust the camera position and lock the camera body by tightening screws. This screw is used to fix body. Tilt angle hole.
Installation OSD Setup Menu Section 2(B) is installation for FD1-IR Series. 2.1(B) Disassembling the Camera Before you mount and adjust the camera, follow these steps to disassemble the camera. 1. Insert a coin or flat tool to the side hole and twist to remove the dome cover. 2. Remove the dome cover (#3) by gently pulling it free from the tilt adjustment bracket (#2). 3. Set the dome cover (#3) aside. 1. Bottom case 2. Tilt adjustment bracket 3.
Installation OSD Setup Menu 2.2(B) Connecting the Wiring Refer to Figure 1-4 and Figure 1-5 to connect the video connect output connector (A) and DC 12V power connector (B). Caution: For DC power supply use, make sure the polarity is correct to avoid malfunction and / or camera damage. 2.3(B) Mounting the Camera 1. Attach the mounting template to the wall or ceiling. 2. Drill two holes, then insert the screw anchors (#1) into the holes. 3.
Installation OSD Setup Menu 2.4(B) Adjusting the Camera Position The dome camera has three axes for positioning the camera. While monitoring the picture on the monitor, adjust the camera position as follows: • Pan Adjustment: Rotate 3D assembly in the base. Do not turn assembly more than 360°as this may cause the internal cables to twist and disconnect or break. • Tilt Adjustment: After loosening the screw on the bracket, position the camera as desired, then tighten the screw back to the bracket.
Installation OSD Setup Menu 2.5(B) Adjusting the Lens (if equipped with varifocal lens) Refer to Figure 2-3(B), for FD1-IRV9, please carry out the following steps to adjust the lens: 1. Loosen the zoom lever (#5) counter-clockwise a little, then rotate the zoom lever and determine the image view. 2. Loosen the focus lever (#4) counter-clockwise a little, then adjust the focus for optimum picture sharpness. 3. Re-tighten the zoom lever and focus lever after adjustment.
Specification 3. Specifications FD1-F Series Camera System Type Format Optical System Image Size IR Cut Filter Electronic Syncronization Horizontal resolution Field Of View Min.
Specification FD1-IR Series Camera System Type Format Optical System Image Size IR Cut Filter Electronic Syncronization Horizontal resolution Lens Options Field Of View Min.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
PRODUCT WARRANTY AND RETURN INFORMATION written explanation with the product when returned. Method of return shipment shall be the same or equal to the method by which the item was received by Pelco. RETURNS To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair) and designated return location.
www.pelco.
