Installation Manual

ManualsBrandsPelco ManualsElectronics1 Channel Video Fiber Transmitter ST Connector, Single Mode

C5632M / REV 11-06-12

Tech SupporT: (800) 289-9100 InTernaTIonal: +1 (559) 292-1981

INSTALLATION AND OPERATION MANUAL

FSV10D1(M,S)1(ST,FC)

10-BIT DIGITAL VIDEO TRANSMITTER

WITH BIDIRECTIONAL RS422 OR COAXITRON

UP-THE COAX DATA FOR PELCO™ DOME CAMERAS

The FSV10D1(M,S)1(ST,FC) series video transmitters and receivers support

simultaneous broadcast-quality video transmission of 10-bit digital video and

bidirectional RS422 data or Coaxitron

up-the-coax protocol, utilizing time-based

correction to achieve distances up to 69km (43mi), over one multimode or single mode

optical fiber. The transmitters are designed to plug directly into the Pelco Spectra® IV

dome, and connect with power, video input and two way data via the Pelco electrical

connector. See Figure 3 on Page 4 for in-dome installation instructions.

The receiver can be configured to communicate with the in-dome transmitter in RS422

or Coaxitron mode. See Figures 7 and 8 on Page 6 for configuration settings.

See Figures 1 – 8 for complete installation details.

Summary of content (8 pages)

PAGE 1
INSTALLATION AND OPERATION MANUAL FSV10D1(M,S)1(ST,FC) 10-bit digital video TRANSMITTER with bidirectional RS422 OR COAXITRON® UP-THE COAX DATA for Pelco™ dome cameras The FSV10D1(M,S)1(ST,FC) series video transmitters and receivers support simultaneous broadcast-quality video transmission of 10-bit digital video and bidirectional RS422 data or Coaxitron® up-the-coax protocol, utilizing time-based correction to achieve distances up to 69km (43mi), over one multimode or single mode optical fiber.
PAGE 2
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
PAGE 3
INSTALLATION AND OPERATION MANUAL FSV10D1(M,S)1(ST,FC) FIGURE 1 – TRANSMITTER Each model includes one optical fiber cable as follows: • FSV10D1M1ST – 13 inch multimode ST cable • FSV10D1S1ST – 13 inch single mode ST cable • FSV10D1S1FC – 13 inch single mode FC cable MULTIMODE OR SINGLE MODE OPTICAL FIBER FIGURE 2 – TRANSMITTER TOP Tech Support: (800) 289-9100 International: +1 (559) 292-1981 BOTTOM C5632M / Rev 11-06-12
PAGE 4
INSTALLATION AND OPERATION MANUAL FSV10D1(M,S)1(ST,FC) FIGURE 3 – MOUNTING INSTRUCTIONS See your Pelco Spectra IV Dome installation manual for details of dome installation. Remove lower dome and dome drive from Spectra IV dome according to the dome’s instruction manual to reveal the back box (A). A Open the hinged door of Spectra IV back box to reveal the circuit board (B).
PAGE 5
INSTALLATION AND OPERATION MANUAL FSV10D1(M,S)1(ST,FC) FIGURE 3 – MOUNTING INSTRUCTIONS (CONT’D) Route the power cord from the 24 volt power connector away from the fiber transmitter, as seen demonstrated by the red and black wires here. Do not leave a “service loop” of power cord in the back box. All slack wire should be removed from the power cord.
PAGE 6
MECHANICAL INSTALLATION INSTRUCTIONS FIGURE 5 – LED INDICATORS (RECEIVER) As displayed on FRV10D1(M,S)1(ST,FC) Receiver LINK VIDEO DATA IN DATA OUT POWER GREEN Communication link has been established over optical fiber An active video signal is present on the BNC connector. An active data signal is present on the input pins of the data connector. An active data signal is present on the output pins of the data connector. Unit powered up RED Communication link has not been established.
PAGE 7
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
PAGE 8
www.pelco.