C2604M.
C2604M.
C2604M.book Page 3 Friday, July 14, 2006 1:08 PM Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Description . . . . . . . . . . . . . . .
C2604M.book Page 4 Friday, July 14, 2006 1:08 PM Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
C2604M.book Page 5 Friday, July 14, 2006 1:08 PM The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. C2604M (7/06) CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN.
C2604M.book Page 6 Friday, July 14, 2006 1:08 PM Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules.
C2604M.book Page 7 Friday, July 14, 2006 1:08 PM Product Overview DESCRIPTION The FT85011A/FR85011A fiber transmitter and receiver provide the ability to transmit one unidirectional composite video channel and one bidirectional data channel over one optical fi ber. In addition, patentpending technology provides the solution for allowing Coaxitron® pan/tilt/zoom (PTZ) control data to be transmitted the full distance of the fiber (up to 6 km for multimode fiber and up to 46 km for singlemode fiber).
C2604M.book Page 8 Friday, July 14, 2006 1:08 PM • Meets NEMA TS 2 and Caltrans traffic signal control equipment standards for ambient operating temperature, mechanical shock and vibration, humidity with condensation, high-line/low-line voltage conditions, and transient voltage protection NOTE: Conformal coating is required for operation in environments with relative humidity above 95% (condensing).
C2604M.
C2604M.book Page 10 Friday, July 14, 2006 1:08 PM FRONT PANEL The front panel of the FT85011A transmitter and the FR85011A receiver provides LED indicators that allow you to monitor data activity, signal status, laser status, and operating power (refer to Figure 2). Tx Tx Rx Rx 1 FT85011A TRANSMITTER FR85011A RECEIVER Figure 2.
C2604M.book Page 11 Friday, July 14, 2006 1:08 PM REAR PANEL All connections to the FT85011A transmitter and the FR85011A receiver are made to the rear panel of the modules (refer to Figure 3). 1 2 3 4 5 6 7 8 GND 3 12 4 3 12 4 0 9 0 1 2 3 4 5 6 7 8 GND 5 9 8 7 6 5 8 7 6 1 FT85011A TRANSMITTER 1 FR85011A RECEIVER Figure 3.
C2604M.book Page 12 Friday, July 14, 2006 1:08 PM Installation PACKAGE CONTENTS The following items are supplied: 1 FT85011A transmitter or FR85011A receiver 1 Regulated switching power supply with four plug adapters (North American, Australian, U.K., and European configurations); 100-240 VAC, 50-60 Hz input, 12 VDC output 1 Wall clip with two 4-40 x 0.
C2604M.book Page 13 Friday, July 14, 2006 1:08 PM With the FT85011A transmitter/FR85011A receiver powered off, set the Data Selection switch to the required data communication using a small screwdriver. Refer to Table A for data communication switch settings. Table A. Data Communication Switch Settings Data Communication RS-232 Switch Setting 0 (default setting) RS-422 1 RS-485 2-Wire 2 RS-485 4-Wire 3 Manchester/Bi-Phase 4 Coaxitron 5 NOTE: Switch positions 6-9 are not used.
C2604M.book Page 14 Friday, July 14, 2006 1:08 PM MOUNTING The FT85011A transmitter/FR85011A receiver can be mounted into a rack or can be used as a stan dalone module. As a stand-alone module, the unit can be placed on a desktop or can be mounted to a wall. NOTE: As a matter of convenience, it is recommended that you set the desired data communication before mounting the FT85011A transmitter/FR85011A receiver. To set the desired data communication, refer to the Data Communication Setup section.
C2604M.book Page 15 Friday, July 14, 2006 1:08 PM Mounting the Transmitter/Receiver Using the Wall Clip NOTE: Before mounting the FT85011A transmitter/FR85011A receiver to a wall, ensure that there is adequate space at both ends for viewing the front-panel LEDs and for making the various rear-panel cable connections. To attach the FT85011A transmitter/FR85011A receiver to a wall using the supplied wall clip, refer to Figure 5 and do the following: 1.
C2604M.book Page 16 Friday, July 14, 2006 1:08 PM CONNECTIONS Connections to the FT85011A transmitter and the FR85011A receiver are made on the rear panel of the modules and consist of the following: • Power connection NOTES: – A 12 VDC or 24 VAC power supply can be used to power the transmitter/receiver when used as a stand-alone module. A 12 VDC power supply is provided.
C2604M.book Page 17 Friday, July 14, 2006 1:08 PM Table B.
C2604M.
C2604M.
C2604M.
C2604M.
C2604M.
C2604M.
C2604M.book Page 24 Friday, July 14, 2006 1:08 PM Troubleshooting LED indicators on the front panel of the FT85011A transmitter/FR85011A receiver (refer to Figure 2) allow you to monitor signal status, laser status, data activity, and operating power. Table C provides information about the front-panel indicators and associated troubleshooting guidelines . Table C.
C2604M.book Page 25 Friday, July 14, 2006 1:08 PM Table C. Troubleshooting with Front-Panel Indicators (Continued) Indicator Color Meaning Possible Cause Corrective Action Optic Fault LED Green The optical signal is being received and laser is operating properly. — No action required. Red The optical signal is not being received. Remote fiber module is not powered on. Check power connections. Replace power supply if necessary. Fiber optic cable is not connected. Check fiber optic connections.
C2604M.book Page 26 Friday, July 14, 2006 1:08 PM Table C. Troubleshooting with Front-Panel Indicators (Continued) Indicator Color Meaning Possible Cause Corrective Action Data Tx LED Flashing amber Data is being trans- — mitted onto the fiber by the data port. Red Data Selection switch is set to an invalid setting. Not lit Data is not being Data is not present on the transmitted onto the channel. fiber by the data Data connection is faulty. port. Data communication cable is defective.
C2604M.
C2604M.book Page 28 Friday, July 14, 2006 1:08 PM OPTICAL POWER BUDGET, TRANSMISSION DISTANCE, AND LASER CLASS 1 LIMIT FT85011A TRANSMITTER AND COMPATIBLE RECEIVERS Model No. FT85011A Transmitter Compatible Receivers Wavelength Optical Power Budget Maximum Transmission Distance Laser Class 1 Limit* 26 dB† 6 km (3.7 mi)‡ <15.6 mW 26 dB † 6 km (3.7 mi) ‡ <0.78 mW 20 dB † 6 km (3.7 mi) ‡ <15.6 mW 20 dB † 6 km (3.7 mi) ‡ <0.78 mW 28 dB 46 km (28.6 mi)§ <15.6 mW 28 dB 46 km (28.
C2604M.book Page 29 Friday, July 14, 2006 1:08 PM OPTICAL POWER BUDGET, TRANSMISSION DISTANCE, AND LASER CLASS 1 LIMIT FR85011A RECEIVER AND COMPATIBLE TRANSMITTERS Model No. FR85011A Receiver Compatible Transmitters Maximum Transmission Distance Laser Class 1 Limit* 26 dB† 6 km (3.7 mi)‡ <15.6 mW 26 dB † 6 km (3.7 mi) ‡ <0.78 mW 1310 nm (video) 20 dB † 6 km (3.7 mi) ‡ <15.6 mW 850 nm (data) 20 dB† 6 km (3.7 mi)‡ <0.78 mW Wavelength Optical Power Budget Multimode (62.
C2604M.book Page 30 Friday, July 14, 2006 1:08 PM . This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
C2604M.book Page 31 Friday, July 14, 2006 1:08 PM PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic products. • Three years on Genex® Series products (multiplexers, server, and keyboard).
C2604M.book Page 32 Friday, July 14, 2006 1:08 PM ® Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.
