I N S T A L L A T I O N Heavy-Duty Spectra® IV Series In-Ceiling Back Box C3419M-B (11/06)
Installation BACK MOUNTING PLATES 1 CEILING 4 MOUNTING RING 2 2 5 3 6 C3419M-B (11/06)
1. Locate the center point of the mounting location and insert the compass tool. Draw a circle. 2. Cut the circle out of the ceiling. 3. Use the mounting ring as a template and mark the screw hole pattern onto the mounting surface. Prepare the holes. 4. Install the mounting plates. Use the eight 10-32 x 3-inch screws (supplied) and install the mounting ring (A) and two back mounting plates (B). a. Line up the mounting ring with the eight fastener holes. b.
7 ALARMS 8 AUX1 1 2 3 4 5 6 7 GND NO COM NC AUX2 GND VIDEO PWR- GND PWR+ RX- RX+ TX- TX+ UTP+ UTP- 4 C3419M-B (11/06)
7. Install the back box by compressing the spring clips and pushing the back box through the hole. Tighten the screws until you hear a clicking noise. WARNING: An electrical short in the back box may occur if the metal BNC connector is not completely covered by the protective boot. 8. Connect wiring to the circuit board inside the back box. When finished, close the door to the back box and turn on the power. The green LED will light.
SWITCH 1 AND 2 9 11 BALL STUD TRIM LEASH BALL STUD RECEIVER BARREL KEY LOCK 10 6 C3419M-B (11/06)
9. Configure DIP switches SW1 and SW2 located on the top of the dome drive. For DIP switch settings, refer to the labels located on the top of the dome drive or to the Switch Settings section of this manual. NOTE: When connecting more than one Spectra® dome to a single controller, terminate the unit farthest from the controller. To terminate the dome drive set the SW2-10 switch to the ON position. 10. Install the dome drive. Refer to Table D for a list of a compatible dome drives and back boxes.
Switch Settings WARNING: If you are using D-type or P-type control, your system may not operate if the baud rate and address switches are not set correctly. The switches are set at the factory at the defaults for D-type control (2400 baud and address 1). Table E. Switch Settings for SW2 Special Systems Switch Number AD-32 Preset System 1 2 3 4 5 6 7 8 9 10 ON CM9502 Setting ON Vicon Not currently available; SW2-3 is reserved for future use.
Table F. Switch Settings for SW1, P-Type Control NOTE: For Coaxitron controls, SW1 is not used; set all switches OFF. For D-type control systems, refer to Table G.
SWITCH SETTING SPECTRA ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 10 SWITCH SETTING SPECTRA ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 31 ON ON ON ON ON OFF OFF OFF 71 ON ON ON OFF OFF OFF ON OFF 32 OFF OFF OFF OFF OFF ON OFF OFF 72 OFF OFF OFF ON OFF OFF ON OFF 33 ON OFF OFF OFF OFF ON OFF OFF 73 ON OFF OFF ON OFF OFF ON OFF 34 OFF ON OFF OFF OFF ON OFF OFF 74 OFF ON OFF ON OFF OFF ON OFF 35 ON ON OFF O
SWITCH SETTING SPECTRA ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 SWITCH SETTING SPECTRA ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 111 ON ON ON ON OFF ON ON OFF 151 ON ON ON OFF ON OFF OFF 112 OFF OFF OFF OFF ON ON ON OFF 152 OFF OFF OFF ON ON OFF OFF ON ON 113 ON OFF OFF OFF ON ON ON OFF 153 ON OFF OFF ON ON OFF OFF ON 114 OFF ON OFF OFF ON ON ON OFF 154 OFF ON OFF ON ON OFF OFF ON 115 ON ON OFF OFF ON
SWITCH SETTING SPECTRA ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 12 SWITCH SETTING SPECTRA ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 191 ON ON ON ON ON ON OFF ON 223 ON ON ON ON ON OFF ON 192 OFF OFF OFF OFF OFF OFF ON ON 224 OFF OFF OFF OFF OFF ON ON ON ON 193 ON OFF OFF OFF OFF OFF ON ON 225 ON OFF OFF OFF OFF ON ON ON 194 OFF ON OFF OFF OFF OFF ON ON 226 OFF ON OFF OFF OFF ON ON ON 195 ON ON OFF OFF
Specifications GENERAL Construction Back Box Dome Drive Lower Dome ELECTRICAL (Dome Drive Only) Input Voltage Cage Color Aluminum Aluminum, thermoplastic Clear polycarbonate, 0.090-inch thick 0.12 x 0.30-inch cast stainless steel Black, for maximum discreetness Cable Entry (Back Box) 0.
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC. This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. If a warranty repair is required, the Dealer must contact Pelco at (800)þ289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information: Exceptions to this warranty are as noted below: 1. Model and serial number 2. Date of shipment, P.O.
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.
