® IOP19 Series Integral Color Camera/Lens for SB1900 Series Dome Installation/Operation Manual C718M (10/96) Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • (1-209) 292-1981 • (800) 289-9100 FAX (800) 289-9150 or (1-209) 292-3827
(This page intentionally left blank.
TABLE OF CONTENTS Section Page 1.0 WARNINGS ........................................................................................................................................ 1 2.0 SCOPE ...............................................................................................................................................2 3.0 DESCRIPTION ...................................................................................................................................2 3.1 MODELS .......
LIST OF ILLUSTRATIONS Figure 1 2 3 4 5 6 7 8 9 Page IOP Package Installation .............................................................................................................. 2 Wiring Diagram for SB1900 Dome and IOP Package ................................................................. 3 Back Focus Adjustment ............................................................................................................... 4 Camera Adjustments ...................................................
IOP19 SERIES INTEGRAL COLOR CAMERA/LENS PACKAGE FOR SB1900 SERIES DOMES 1.0 WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 3. Only use replacement parts recommended by Pelco. 1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes. 4. 2.
2.0 SCOPE 4.0 INSTALLATION This manual covers the IOP19 Series of integral color camera/lens packages. To install the camera/lens package in your dome, follow the steps below. 3.0 DESCRIPTION 1. Disconnect main power to the back box. Pelco's IOP19 Series of integral color camera/lens combinations are specifically designed for use in the SB1900 Series of indoor surveillance dome enclosures. 2. Remove the dome drive from the back box. 3. Refer to Figure 1.
Figure 2.
5.0 ADJUSTMENTS Your optics package comes from the factory adjusted for a broad range of lighting conditions. For this reason, you may find it necessary to adjust your optics package to tailor the picture to your specific viewing environment.
5.2 SHUTTER SPEED 5.3 AUTO GAIN CONTROL This optics package is provided with adjustable shutter speeds. This feature allows minimal streaking when a very fast moving object passes in front of the nonmoving optics package. The shutter speed is factory set to 1/60 second. You can select one of eight shutter speeds (refer to Figure 4). Refer to Figure 4. The AGC control setting should be set and left in the ON position.
5.4 WHITE BALANCE (ATW/AWB SWITCH) In the ATW (Automatic Tracing White Balance) position, the white balance is continuously adjusted to take into account variations in the incident light conditions. In the AWB (Automatic White Balance) position, when the LOCK button is pressed, the white balance is automatically adjusted, and the setting is stored in memory. When the switch is set to this position the white balance always takes the previously stored value.
6.0 WIRING DIAGRAM Figure 5.
7.0 EXPLODED ASSEMBLY DRAWING—TVH6 Figure 6. TVH6 Camera/Lens Combination Exploded Assembly Drawing 7.1 MECHANICAL PARTS LIST (Figure 6) 8 Item Qty 1 2 3 4 5 6 7 8 A B C D E F G H J K 1 1 1 1 1 1 1 1 2 5 5 16 2 2 2 5 Description Part Number Lens, 1/2", 6X motorized zoom, F1.2, 8.5-51 mm Frame, 6X lens package Not used Clamp, wire fatigue Top cover Back cover Camera, Sony, 1/2", high resolution, color (NTSC) Circuit board, IOP camera interconnect Not used Screw, 1/4-20 x .
8.0 EXPLODED ASSEMBLY DRAWING—TVH10 Figure 7. TVH10 Camera/Lens Combination Exploded Assembly Drawing 8.1 MECHANICAL PARTS LIST (Figure 7) Item Qty 1 2 3 4 5 6 7 8 A B C D E F G H J K 1 1 1 1 1 1 1 1 2 5 5 13 2 2 2 5 Description Lens, 1/2", 10X motorized zoom, F1.2, 8-80 mm Frame, 10X lens package Not used Clamp, wire fatigue Top cover Back cover Camera, Sony, 1/2", high resolution, color (NTSC) Circuit board, IOP camera interconnect Not used Screw, 1/4-20 x .
9.0 SPECIFICATIONS ELECTRICAL MECHANICAL Color NTSC (EIA) Camera Module Mounting Bracket Input Voltage: 24 VAC, 60 Hz Construction: 0.050" aluminum Power Requirements: Less than 5 watts Dimensions: See Figures 8 and 9 Video Output: 1 V p–p composite video into 75 ohms Operating Temperature: 14° to 131°F (-10° to 55°C) Imaging Device: 1/2" CCD Illumination: 2.5 LUX @ F1.
10.0 WARRANTY AND RETURN INFORMATION WARRANTY RETURNS Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex® Series products (multiplexers, server, and keyboard).
Pelco 300 West Pontiac Way Clovis, CA 93612-5699 (209) 292-1981 • (800) 289-9100 FAX (800) 289-9150 or (209) 292-3827 • DataFAX (800) 289-9108 or (209) 292-0435 International customers call 1-209-292-1981 or FAX 1-209-348-1120 (Product specifications subject to change without notice.
