Sarix® Professional 3 IBP Series Environmental IR Bullet Camera Installation Manual IBP131-1ER IBP232-1ER IBP231-1ER IBP532-1ER IBP331-1ER IBP235-1ER IBP531-1ER IBP335-1ER C6630M-A-EN (07/19)
Contents Important Notices ......................................................................................................................................................................... 3 REGULATORY NOTICES [FCC CLASS A] ................................................................................................................... 3 RADIO AND TELEVISION INTERFERENCE ................................................................................................................
Important Notices REGULATORY NOTICES [FCC CLASS A] This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules.
Judgment as to the suitability of the products for users' purposes is solely the users' responsibility. Users shall determine the suitability of the products for their own intended application, picture rate and picture quality. In the event users intend to use the video for evidentiary purposes in a judicial proceeding or otherwise, users should consult with their attorney regarding any particular requirements for such use.
Preface This installation manual is to be used as a reference for the installation of the camera unit including wire connection, camera installation, and camera adjustment. This manual provides the following information. Product Overview: The main functions and system requirements of the unit. Installation and Connection: Instructions on unit installation and wire connections.
1. Product Overview 1.1 Dimensions The dimensions of the Sarix Professional 3 Series Environmental IR Bullet are depicted within the Figure 1-1 below. NOTE: VALUES IN PARENTHESES ARE INCHES; ALL OTHERS ARE CENTIMETERS. ENVIRONMENTAL IR BULLET - 5-50MM ENVIRONMENTAL IR BULLET - 2.
1.2 Model Instruction The physical appearances and installation methods for the models indicated within the list below are similar. Consequently, in this manual the IBP335-1ER model is an example to use as a reference to apply to all the varied models. Model Description IBP131-1ER 1MP Environment Bullet with IR and 2.8-12mm Lens IBP231-1ER 2MP Environment Bullet with IR and 2.8-12mm Lens IBP331-1ER 3MP Environment Bullet with IR and 2.8-12mm Lens IBP531-1ER 5MP Environment Bullet with IR and 2.
1.3 Physical Characteristics 3 4 5 6 2 1 7 FIGURE 1-2: CAMERA CONNECTIONS AND FEATURES 1/2 1. Camera Main Body 2. Sun Shield: Minimize the effects of rain and sunlight on image quality. 3. RJ-45 Network Port: Connects the camera to the IP network. 4. Power Connector (Black / Red): Connects to the external power source DC12V or AC24V. 5.
8 9 10 11 12 13 14 FIGURE 1-3: CAMERA CONNECTIONS AND FEATURES 2/2 8. Micro-SD Card Slot: This slot is for inserting a micro SD card for extra file storage. NOTE: An SDHC or SDXC card capable of a minimum write speed of 10 MB/sec is recommended for recording HD video. Pelco also recommends the SD card's operating temperature range be suitable for the environment it is intended to be used in. 9. Ethernet / PoE: The port in the middle is connected to a PoE cable.
14. Safety Wire: The safety lanyard is used to prevent the access cover from falling. Be sure to store the safety wire inside the camera before locking the access cover to ensure that the camera remains waterproof. 2. Installation and Connection 2.1 Unpacking Everything Check all items in the product box against the order form and the packing slip.
2.3.2 Installing the Camera 2.3.2.1 WALL SURFACE MOUNT Install the environmental IR bullet camera to a wall surface as shown in the following procedure. NOTE: The mounting height above ground level shall be more than 3 meters for wall mount height. 1 3 FIGURE 2-1: MOUNTING TEMPLATE FOR WALL SURFACE MOUNT FIGURE 2-3: WALL SURFACE MOUNT 2/2 2 I II FIGURE 2-2: WALL SURFACE MOUNT 1/2 1. Drill 6 mm (0.25”) outer holes based on the mounting template and hammer the plastic anchors into the holes. 2.
WITH IBP3BBAP-ES Also, you can mount the camera to the wall using IBP3BBAP-ES, a Sarix Environmental Surface Mount for bullet. Refer to the figure below for surface installation with IBP2BB-ES. 4 2 3 1 5 FIGURE 2-4: SURFACE MOUNT WITH IBP3BBAP-ES 1. Fix the IBP3BBAP-ES backbox (#1) to the desirable surface by drilling three holes and fastening it with screws. 2. Incoming cables should be fed through the backbox from the back or side depending on your installation. 3.
2.3.2.2 IN-CEILING INSTALLATION The In-Ceiling Installation is mounting the camera into the ceiling with IBP3BBAP-EI, a Sarix Environmental In-Ceiling Mount for bullet. 1 2 5 3 4 FIGURE 2-5: IN-CEILING INSTALLATION WITH IBP3BBAP-EI 1. Make a round hole for IBP3BBAP-EI backbox (#1) to fit in. NOTE: The recommended diameter of the hole is 26.9mm. 2. Incoming cables should be fed through the backbox from the back or side depending on your installation. 3.
2.3.3 Connecting the Cables Based on your needs, connect the power cable to the power port via one of the following 3 options. AC 24V: Connect a power cable that supplies AC24V power source to the terminal block, and then insert the terminal block into the power port. DC 12V: Connect a power cable that supplies DC12V power source to the terminal block, and then insert the terminal block into the power port. NOTE: The polarities should be matching when using DC12V power source.
2.3.4 Adjusting the Sun Shield The environmental IR series are designed with capability to operate under rugged environments and thus will possibly be subject to influences from sunlight or rain. Sun shield is therefore coated on the camera to prevent damage from those outside effects. Refer to the figure below to adjust the sun shield. 1. Loosen the two screws on the shield hood. 2. Move the sun shield forward or backward to adjust till the desired position.
A B C Locking Screw FIGURE 2-8: POSITIONING THE CAMERA 2.3.6 Adjusting the Focus 1. View the camera image using the browser (refer to the Operation Manual). 2. Use the settings in the Web interface (refer to the Operation Manual) to adjust the zoom and focus of the lens to the desired field of view. 3. Also, the focus can be adjusted by moving the zoom slider and using the Focus options in the live webpage. NOTE: Focus adjustment is done exclusively with Web UI.
Pelco Troubleshooting Contact Information If the instructions provided fail to solve your problem, contact Pelco Product Support at 1-800-289-9100 (USA and Canada) or +1-559-292-1981 (international) for assistance. Be sure to have the serial number available when calling. Do not try to repair the unit yourself. Leave maintenance and repairs to qualified technical personnel only.
Pelco 625 W. Alluvial Fresno, California 93711 United States (800) 289-9100 USA & Canada Phone (800) 289-9150 USA & Canada Fax +1 (559) 292-1981 International Phone +1 (559) 348-1120 International Fax www.pelco.com Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. ONVIF and the ONVIF logos are trademarks of ONVIF Inc. All other product names and services are the property of their respective companies.
