® Installation/Operation ICS-DO101ABK Integrated Camera System for the MR5000 Series Public View System C2436M-B (9/02) ' Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.
[2] Pelco Manual C2436M-B (9/02)
TABLE OF CONTENTS IMPORTANT SAFEGUARDS AND WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ADJUSTMENTS (COLOR CAMERA ONLY) . . . . . . . . . . . . . . . . . .
[4] Pelco Manual C2436M-B (9/02)
IMPORTANT SAFEGUARDS AND WARNINGS 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6 or 6P enclosure, it is designed for indoor use only and must not be installed where exposed to rain and moisture. 3. Use only installation methods and materials capable of supporting four times the maximum specified load.
2 Prepare Video and Electrical Cabling 1. Temporarily remove the bottom end cap of the MR5000 Series mount if it is installed. 2. Feed the 42-inch video cable (provided) through the monitor feedthrough hole in the mount arm and out the bottom end of the mount arm. 3. Pull power wires through the ICS-DO101ABK feedthrough located at the bottom of the mount arm. Remove the .50-inch plug if it is installed. 4. Pull wires through the adapter plate of the ICS-DO101ABK and into the base of the ICS-DO101ABK. 5.
CAUTION Heater elements could be hot! When camera power is on, use caution when adjusting the camera. This applies to all models. 4 Install Camera 1. Some indoor installations do not require a heater. If the installation does not require a heater, remove the heater board from the camera assembly. To remove the heater apply pressure and press on the corner of the board. 2. If the heater is installed, plug the heater connector from the camera into the mating connector inside the base.
5 Install Dome and Trim Ring ADJUSTMENT GROOVE DOME LINER 1. Align the screw holes in the trim ring with those in the camclosure base. LOOSEN SCREWS 2. Domes with Liners (only) – Position the viewing window over the lens of the camera. a. Loosen the three Phillip screws located in the dome. b. Insert the blade of a standard screwdriver in one of the adjustment grooves. Move dome into position. c. Tighten the three Phillip screws to lock liner in place. 3.
Focus Adjustment for Fixed Focal Length Lens with Auto Iris CAUTION Heater elements could be hot! When camera power is on, use caution when adjusting the camera. To adjust the focus, it may be necessary to remove the heater board in order to loosen the locking screw on the bottom of the lens. To remove the heater board: 1. Disconnect the four-pin heater wiring. 2. Wait for the heater elements to cool if they are hot. 3. Apply pressure and press on the corner of the board. To adjust the focus: 1. 2. 3. 4.
Switch Settings for Fixed Focal Length Lens Without Auto Iris Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fixed lighting conditions where there are no bright spots that darken other picture details. Manual backlight compensation is used in fixed lighting conditions to optimize the picture detail when there are bright spots.
SPECIFICATIONS Electrical Input Voltage: Power Consumption: Video Connector: Operating Temperature: General Cable Entry: Pan/Tilt Adjustment: 12 VDC or 24 VAC, ±10% Ratings: NEMA 4, IP 66 when installed properly CE UL/cUL Aluminum with steel camera mounting bracket and polycarbonate dome Gray polyester powder coat 13 watts or less BNC -50° to 122°F (-46° to 50°C) De-ices to -10°F (-23°C) 3/4-inch (1.91 cm) conduit fitting and 3/4-inch (1.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex® Series products (multiplexers, server, and keyboard).
