Next Gen Sarix® Enhanced IME Series Mini Dome Cameras Installation Manual C1338M 7/17 1
Contents Important Notices................................................................................................................................................. 3 Legal Notice ......................................................................................................................................................... 3 Regulatory Notices ..............................................................................................................................................
Important Notices For more information about Pelco’s product-specific important notices and thereto related information, refer to www.pelco.com/legal. Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Introduction The NextGen Sarix® IME Series IP cameras feature SureVision technology that seamlessly delivers advanced low-light performance with wide dynamic range (WDR) and anti-bloom technologies that operate simultaneously. They are part of Pelco’s Enhanced (E) range of cameras, providing industryleading image quality and performance. The IME Series mini dome camera is easy to install, offers flexible mounting options, and uses a standard Web browser for easy remote setup and administration.
Models IME129-1IS Indoor, 3 ~ 9 mm focal range, surface mount, 1MPx, white IME229-1IS Indoor, 3 ~ 9 mm focal range, surface mount, 2MPx, white IME329-1IS Indoor, 3 ~ 9 mm focal range, surface mount, 3MPx, white IME129-1ES Environmental, 3 ~ 9 mm focal range, surface mount, 1MPx, light gray IME229-1ES Environmental, 3 ~ 9 mm focal range, surface mount, 2MPx, light gray IME329-1ES Environmental, 3 ~ 9 mm focal range, surface mount, 3MPx, light gray IME129-1RS Environmental, 3 ~ 9 mm focal range,
Getting Started Before installing your device, thoroughly familiarize yourself with the information in the installation section of this manual. NOTES: • Pelco recommends connecting the device to a network that uses a Dynamic Host Configuration Protocol (DHCP) server to address devices. • Do not use a network hub when configuring the network settings for the device. • To ensure secure access, place the device behind a firewall when it is connected to a network.
Surface Mount Models Supplied Parts List Qty Description 1 Camera 1 IME Series Mini Dome IP Camera Installation manual 1 Important Safety Instructions 1 Resource sheet 1 RoHS 10 (China only) 1 Power adapter plug (optional) 2 Plastic expansion anchors 3 M4 x 25 mm self-tapping screws 1 Torx T20 security bit (Outdoor Cameras Only) 1 Mounting plate (Type 4x) 4 8-32x.5 C-sink (check fit to plate) 2 6-32x.5 C-sink (check fit to plate) 2 M4x.
Product Overview (1) RJ-45 Network Port: Connects the camera to the IP network. Also supplies power to the camera (PoE), through the same connector. I. To purchase power adaptor, please contact Pelco for further information. (2) BNC Connector: Not in use. (3) Power Connector: A two-pin connector for 12VDC and 24VAC. To wire the power connector, remove the green power male adaptor that comes already inserted into the camera. Attach the wires per the diagram above (e.g.
Installation Installing the Mount You can install the IME Series mini domes using one of the following mounting methods: • Installation in a suspended ceiling or a fixed ceiling. Refer to In-Ceiling: Indoor and Environmental with IMEICM-I or IMEICM-E • Installation using a pendant mount. Refer to Pendant: Indoor and Environmental with WMVE-SR or WMVE-SW and IMEPM-I or IMEPM-E. • Installation on a wall or a fixed ceiling.
INSTALL SCREWS HERE IF WATERTIGHT SEAL IS NEEDED 3. Determine the mounting location in the ceiling. 4. Use the template to mark the hole on the wall, ceiling, or ceiling tile. 5. Cut the hole for the camera. 6. Pull the wiring through the hole. 7. Move the conduit plug to side or top where needed to use the other hole for wire entry. Tighten the plug. 8. Install the back box as follows: a. Attach and seal the conduit as needed. b.
BASE 10. Tighten the locking screw to secure the camera module position. 11. Secure the anti-drop chain, put on the dome cover, and tighten the dome cover. 12. Put on the trim ring and rotate it clockwise to secure the trim ring on the bracket.
Pendant: Indoor and Environmental with IMEPM-I or IMEPM-E and WMVE-SR or WMVE-SW Supplied Parts List Qty Description 1 Pendant cap 2 M4x8 mechanical screws Installation Guide 1. Optional: Remove the camera dome from camera housing by removing the anti-drop chain. 2. Put the conduit plug on the side of the camera box. 3. Apply grease or Teflon tape to the pendant threads. 4. Put the wiring through the hole on the top of the pendant cap into the camera. 5.
7. Place the camera back box or full camera into the pendant cap and adjust the camera back box by using the self-positioning pillars in the pendant cap. Twist until it snaps fully in. Secure the 2 M4 screws. 8. Replace the camera on the back box (if removed for installation ease). 9. Adjust the angle of lens by pan and tilt by grasping the base. BASE 10. Tighten the locking screw to secure the camera module position. 11. Secure the anti-drop chain, put on the dome cover, and tighten the dome cover.
Surface and Type 4X Mount: Environmental with IMEEBAP-E Installation Guide NOTE: The environmental camera is weather tight, rated IP66 if installed directly to a surface. So, this mounting plate is optional. However, to comply with Type 4X outdoor rating, one must install the Type 4X mounting plate. (The Type 4X plate has a dual function to mount to junction boxes, so you can ignore the additional holes if not installing to a junction box. 1.
10. Install the dome lanyard if removed and then the dome cover and tighten the dome cover screws.
Surface Mount: Indoor Installation Guide 1. Prepare the wire entry holes through the plate and camera box as follows: a. Remove the conduit plug if required and move to the hole not used. 2. Remove the dome cover from the camera (optional). 3. Pull the wire through the conduit hole into the camera. 4. Mount the plate/camera to the surface. 5. Adjust the angle of lens by pan and tilt by the base. BASE 6. Tighten the locking screw to secure the camera module position. 7.
Wall Mount: Indoor with IMEPMB-I Supplied Parts List Qty Description 1 Wall mount bracket 2 Plastic screw anchors 2 M4x25 self-tapping screws 2 M4x8 mechanical screws Installation Guide 1. Place the wall mount bracket at the installation location. 2. Prepare the wire entry holes through the wall mount bracket and camera box. Move the plug if necessary. 3. Install the camera to the wall mount bracket using 2 M4 screws. 4. Adjust the angle of lens by pan and tilt.
5. Tighten the locking screw to secure the camera module position. 6. Install the dome cover and tighten the dome cover.
Positioning the Camera • Pan Adjustment (A): Rotate the lens base until you are satisfied with the field of view. Note that the side conduit hole of the lower case is the point where the camera lens shouldn’t be rotated over. • Horizontal Rotation (B): Rotate 3D assembly in the lens base, but do not turn assembly more than 355° as this may cause the internal cables to be twisted, disconnected, or broken.
Cable Terminations Ethernet Wiring Requirement for PoE Connect a Cat5 cable or higher (Cat5e, Cat6) cable (not supplied) to the RJ-45 network connector. The 8-pin port includes video over Ethernet, and PoE for the camera. PoE injects power over the same cabling that carries the network data, eliminating the need for a separate power supply. This simplifies the installation and operation of the camera without affecting network performance.
Alarm/Relay/Audio Port The 9-pin Alarm/Relay/Audio port has the following pins and pin assignments Table 2 Pin Descriptions for Alarm/Relay/Audio Port Connector No.
IP Address Settings If the camera is connected to a Dynamic Host Configuration Protocol (DHCP) network and DHCP is set to On, the server automatically assigns an IP address to the camera. The default setting for the camera is DHCP On. To set the camera’s IP address manually, set DHCP to Off. NOTE: When DHCP is on, but a DHCP server cannot be found: Next Gen Sarix Enhanced cameras will support two IP addressing schemes: 169.254.x.x and 192.168.0.x (starting from 192.168.0.20).
