Installation Manual

ManualsBrandsPelco ManualsCamera & Photo12 Megapixel 270° Panoramic Surface, Environmental Vandal Network Camera, Gray, US

Table Of Contents

C2283M | 9/15

INSTALLATION MANUAL

Optera IMM Installation

Parts List

Unsupplied Parts

All Models

Camera Lower Dome Documentation 2 Mac Address

Labels

T20 Bit 8-Pin Connector

In-Ceiling Models Surface Mounts Models Pendant Models

Back Box Mounting Plate Surface Mount Pendant Mount Anti-Seize Lubricant

All Models

• Pipe/conduit (if applicable)

• Conduit adapters (if applicable)

• Cat5 (or higher) cable, appropriately terminated for POE+

• 24 AWG, 8-wire multiconductor cable (if using alarm, relays, and/or audio)

• SD card, 32GB SanDisk Extreme

PLUS microSDHC™ UHS-I

Surface Mount Models Pendant Models

1 of the following mounting substrates and fasteners:

• Standard 4 in. square electrical box and appropriate fasteners

• Standard 2-gang electrical box and appropriate fasteners

• Any substrate using 3 standard screws, size M6 or 1/4 in.

WMVE-SR Wall Mount (if using

the wall mount for environmental

and vandal-resistant models)

WMVE-SW Wall Mount (if using

the wall mount for indoor models)

Summary of content (11 pages)

PAGE 1
Optera IMM Installation Parts List All Models Camera In-Ceiling Models Back Box Lower Dome Documentation 2 Mac Address Labels Surface Mounts Models Mounting Plate T20 Bit 8-Pin Connector Pendant Models Surface Mount Pendant Mount Anti-Seize Lubricant Unsupplied Parts All Models • Pipe/conduit (if applicable) • Conduit adapters (if applicable) • Cat5 (or higher) cable, appropriately terminated for POE+ • 24 AWG, 8-wire multiconductor cable (if using alarm, relays, and/or audio) • SD card, 32GB
PAGE 2
Product Overview NOTICE: Pelco recommends installing the camera at a height of 3 meters (10 feet) or higher for best results. To ensure an unobstructed view, the expected field of view should be at least 4 meters (12 feet) away from the camera. R -+ -+ - A+ - R+ R Pa withnom SureVers isio ive n PoE+ To ensure reliable local storage, Pelco recommends using a new 32 GB SanDisk Extreme® PLUS microSDHC™ UHS-I card. If the card has been used or reformatted, local storage may not function properly.
PAGE 3
Wiring Information PoE+ Pin Function Pin PoE+ Mode A PoE+ Mode B 1 Audio Out– 1 TX+, PoE+ 1-2 TX+ 2 Audio Out+ 2 TX–, PoE+ 1-2 TX– 3 Audio In– 3 RX+, PoE+ 3-4 RX+ 4 Audio In+ 4 Not used PoE+ 1-2 5 Alarm Input 5 Not used PoE+ 1-2 6 Ground 6 RX–, PoE+ 3-4 RX– 7 Relay N.O. 7 Not used PoE+ 3-4 8 Relay Return 8 Not used PoE+ 3-4 Installing the In-Ceiling Mount 1. Ø 15.24 cm (6.
PAGE 4
2. Remove either the conduit plug (side) or grommet (top) for side or top wire entry. 3. Prepare the wire entry holes. If using the supplied grommet (plenum rating is not required), set the grommet aside for use later. If using conduit (not supplied), replace with 25mm or 2/4 in. conduit adapters. Installing the Back Box 1. Ensure that the support wings are rotated inward, and push the back box through the mounting hole. 2. Replace the other entry opening with the supplied conduit plug. 3.
PAGE 5
Installing the Pendant Mount The pendant mount attaches to 1-1/2 in. NPT pipe/conduit or wall mount with 1-1/2 in. NPT thread (not supplied). 1. Apply anti-seize lubricant to the NPT pipe/conduit, and install the pendant mount to the conduit. 2. Pull the wiring through the opening. Installing the Surface Mount 1. Reference the Surface Mount template and Install the mounting plate to the mounting substrate to one of the following: • Standard 4 in. square electrical box (not supplied).
PAGE 6
2. Remove either the conduit plug (side) or grommet (top) wire entry. 3. Prepare the wire entry holes: • If using the grommet: Put the grommet (supplied) aside for use in a later step. • If using conduit (not supplied): Insert a 25 mm or 3/4 in. conduit adapter (not supplied). For Environmental Vandal cameras, the conduit adapter and compression glands must be rated for IP66/NEMA 4 applications. 4.
PAGE 7
IP Address Settings By default, the camera attempts to obtain an address via DHCP. You can find and access your camera using Pelco’s Device Utility. If the camera is not connected to a network containing a DHCP server but DHCP is set to On (as it is by default), the camera automatically assigns itself a default IP address 192.168.0.20 on subnet mask 255.255.255.0. Additional cameras will assign themselves IPv4 link local addresses and the next available 192.168.0.x IP addresses in sequential order.
PAGE 8
Installing the Lower Dome NOTICE: 8 You must install the lower dome to ensure proper sensor alignment and image focus. 1. Align the trim ring screw holes with the mount holes. 2. Tighten the fasteners using a hand driver. Ensure that there is no gap between the lower dome and the back box.
PAGE 9
Surface Mount Template Print this template at actual size (100%) to match mounting holes on the surface mounting plate.
PAGE 10
In-Ceiling Mount Template Print this template at actual size (100%) to match mounting holes on the surface mounting plate.
PAGE 11
Pelco by Schneider Electric 3500 Pelco Way Clovis, California 93612 USA (800) 289-9100 Tel (800) 289-9150 Fax +1 (559) 292-1981 International Tel +1 (559) 348-1120 International Fax www.pelco.com Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. ONVIF and the ONVIF logo are trademarks of ONVIF Inc. All other product names and services are the property of their respective companies.