Sarix® Professional IMP Series Environmental Vandal Dome User Manual IMP121-1ES IMP321-1ES IMP121-1RS IMP321-1RS IMP221-1ES IMP521-1ES IMP221-1RS IMP521-1RS C2294M-A-EN (1/16)
Contents Important Notices Statement ........................................................................................................................................................ 5 Warranty Statement ..................................................................................................................................................................... 5 Preface .............................................................................................................................
3.2.1 System ............................................................................................................................................................. 27 3.2.2 Network ............................................................................................................................................................ 30 3.2.3 Imaging.......................................................................................................................................................
Important Notices Statement For information about Pelco’s product-specific important notices and thereto related information, refer to www.pelco.com/legal. Warranty Statement For information about Pelco’s product warranty and thereto related information, refer to www.pelco.com/warranty.
Preface This user manual is to be used as a reference for the installation and manipulation of the camera unit including features, functions, and a detailed explanation of the menu tree. This manual provides the following information: Product Overview: The main functions and system requirements of the unit. Installation and Connection: Instructions on unit installation and wire connections. Administration and Configuration: The main menu navigation and controls explanations. 1.
1.2 Models Introduction The physical appearances and installation methods for the models indicated within the list below are similar. Consequently, please regard this manual where we use the example from IMP521-1RS as a reference to apply to all the varied models.
1.3 Physical Characteristics 1 2 3 4 8 5 9 10 6 7 FIGURE 1-2: CAMERA CONNECTIONS AND FEATURES 1/4 11 12 FIGURE 1-3: CAMERA CONNECTIONS AND FEATURES 2/4 13 17 14 FIGURE 1-4: CAMERA CONNECTIONS AND FEATURES 3/4 8 15 16 FIGURE 1-5: CAMERA CONNECTIONS AND FEATURES 4/4 1. Lower Case: The bottom case of the camera. 2. Lens Base: The physical main body of the camera. 3. Torx Screws of Lens Base * 3: The screws for fixing lens base with lower case. 4.
7. Top Cover: The top cover of the camera. 8. Fool-proofing Design: The design is as a smart isolation to enable/disable auto defog function. 9. Micro SD Card Slot: The slot is for inserting extra micro SD card for file storage. 10. Default & Reset Button: Default: Press the button for 6 seconds to restore the camera’s settings back to the factory default. Reset: Press the button for below 1 second to reboot the camera. 11. Bottom Conduit Hole: The bottom hole for cable entry. 12.
2. Installation and Connection 2.1 Unpacking Everything Check all items in the product box against the order form and the packing slip.
2.3.2 Disassembling the Camera Please refer to the steps in the figure below for correct disassembling order. 1. Loosen the 3 camera top cover screws. 2. Gently pull the top cover downward to take it apart from the camera body. 3. Further loosen the 3 camera lens base screws. 4. Gently lift the camera lens base off from the lower case.
2.3.3 Connecting the Wires After disassembling, the I/O interfaces will be seen on the rear of the lens base. Connect the power cable to the power port via one of the following 3 alternatives. AC 24V: Connect a power cable that supplies AC24V power source to the power terminal. DC 12V: Connect a power cable that supplies DC12V power source to the power terminal.
Step 2. Mark Mounting Area Use the guide pattern to prepare a mounting area for In-Ceiling Flush Mount. 1. Attach the mounting template on a desired mounting surface (normally for in-ceiling). 2. Drill a round hole (∅198mm) based on the template on the surface to have the camera embedded within the hole later. FIGURE 2 - 4: MOUNTING TEMPLATE FOR FLUSH MOUNT Use the mounting template to prepare a mounting area for Surface Mount. 1. Place the supplied mounting template on a mounting surface.
Step 3. Mounting Schemes Method 1: Flush Mount (In-Ceiling) 1. Embed the in-ceiling mount bracket into the hole that was drilled based on the mounting template. FIGURE 2 - 6: FLUSH MOUNT 2. Use a cross screw driver to turn the 2 bracket screws clockwise to extend the locking arms and tighten them securely to compress the locking arms so that the bracket can be fixed within the in-ceiling area firmly.
3. Based on your needs, use the bottom conduit hole or side conduit hole on the lower case for cable entry and connect the required cables. NOTE: Please properly lock the conduit hole plug on the unused hole. For example, lock the side conduit hole with the plug while using the bottom conduit hole for cable entry and vice versa. 4.
Method 2: Surface Mount After cable entry and wiring, align the red dots of lower case and lens base followed by securing the torx screws tightly. After adjusting focus angle, align the red dots of lens base and top cover followed by fastening the torx screws to complete the procedure. FIGURE 2 - 9: SURFACE MOUNT 1. Based on your needs, use the bottom or side conduit hole on the lower case for cable entry and connect the required cables first.
Method 3: Pendant Mount (requires pendant adapter mounting accessory) NOTE: Mounts and conduits must be sealed to prevent condensation in the camera The Pendant Installation involves mounting the camera to the wall with IMPPM-1ER Sarix Environmental Pendant Mount for Environmental Vandal Dome. The camera must be installed in the back box with a 3/4” rain-tight compression gland (#1) and a lock nut (#2) as shown below. The compression gland and lock nut are not provided.
2. Attach the lens base to the pendant mount back box after wires connection and securely fasten the 3 screws of the lens base by the torx wrench (supplied). Finally, assemble the top cover with the lens base, which is already attached to the back box, followed by fastening the 3 screws of top cover to complete the installation.
If you possess a safety wire (sold separately), connect the safety wire with one end to the mounting surface and the other end to the safety-cord screw of the camera. Depending on different applications, please connect the safety wire to the corresponding safety-cord screw as shown in the following figures. Safety-cord screw Safety-cord screw FIGURE 2 -13: SAFETY-CORD SCREW 2.3.5 Top Cover Defog Defog function, which heats up camera to overcome certain extreme weather conditions (e.g.
2.3.6 Adjusting the Camera Position The camera has three axes for adjusting field of view on different applications. While screening live view on your monitor, adjust the position by procedures below simultaneously for desired focusing position. Pan Adjustment (A) Rotate the lens base until you are satisfied with the field of view. Note that the side conduit hole of lower case is the point where the camera lens shouldn’t be rotated over.
2.3.8 Network Topology The unit, which is equipped with Ethernet RJ-45 network interface, can deliver video images in real time via either Internet or Intranet. Please refer to the skeleton drawings shown below to aid your understanding.
2.3.9 System Requirements The table below lists the minimum requirements to implement and operate a unit. Network and processor bandwidth limitations might cause the video stream to pause or appear pixilated when additional Web-interface users connect to the camera. Decrease the images per second (ips), resolution, compression, or bit rate settings of the Web interface video streams to compensate for network/processor limitations.
2.4 Connection 2.4.1 Default IP address The unit’s default IP address is 192.168.0.20 and sub mask is 255.255.255.0. When setting default IP address of 192.168.0.20 the camera will check to see if that address is already in use and will bump the last octet of the address by 1 if it is. The bump last octet of IP Address by 1 will continue until an unused IP address is found.
2.4.2.3 Viewing Preparation Images of the unit can be viewed through Microsoft Internet Explorer 8 or later. Before viewing, follow these steps to enable the display. 1. Enable Cookies On the Privacy tab, move the settings slider to Low or Accept All Cookies. 2. Change Security in Internet options and click Custom Level to open the Security Settings – Internet Zone screen. NOTE: If the camera operates inside of the intranet, click the Intranet icon.
3. Administration and Configuration 3.1 Live Simply click on Live on the top right side of the browser window while accessing the IP address of the unit, and a live video is displayed directly in the browser window. When clicked on Settings, a window will pop up for configuring “System”, “Network”, “Imaging”, “A/V Streams”, “Users”, and “Events”. Please refer to 3.2 Settings on page 26 for more information. The current logged in identity shows to the right of the Help.
3.1.1 Zoom and Focus Controls Zoom Zoom In: Click and drag the slider rightward to zoom the lens in. Zoom Out: Click and drag the slider leftward to zoom the lens out. Focus Full Range Auto-Focus: Click the button for the camera to start a full-range search to find the optimal focal point for the scene. Quick Auto-Focus: Click the button for the camera to start a quick search to find the optimal focal point for the scene.
3.2.1 System Use the System tab to change the device name, configure the time settings, set up the text overlay for the live view, get backup, display system information and update firmware version. You can also use the System tab to generate a system log, reboot the camera, or to restore the camera's factory default settings. FIGURE 3-3: SYSTEM SETTINGS Generate System Log 1. Click the System tab. 2.
3.2.1.1 General Settings FIGURE 3-4: GENERAL SETTINGS Device Name Change the Device Name by following steps: 1. Click the Device Name box and highlight the text. 2. Type a user-friendly name into the Device Name box (2 to 64 characters). A user-friendly name makes it easier to recognize the device on the network. Examples of user-friendly names are Front Door, Lobby, or Parking Lot. 3. Click Save to save the new device name, or click Reset to restore to the previously saved device name.
3. Select the format in which the date and time will appear from the Display Format drop-down field if you have opted to show the Date/Time Overlay. 4. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it. Text Overlay 1. Configure the text overlay settings: Background: Set the background color for the text overlay as black or transparent.
3.2.1.3 System Information The System Information page fields are read-only and include the firmware version, hardware version, model number, and serial number of the system are revealed here as below figure. This information is typically required by Pelco Product Support for troubleshooting purposes. FIGURE 3-6: SYSTEM INFORMATION 3.2.1.4 Firmware Update Users can update system firmware if available. All camera motions will shut down during firmware update.
3.2.2.1 General Set the General Network Settings for network communication settings. FIGURE 3-9: GENERAL NETWORK SETTINGS System Settings Settings under the System Settings are Hostname, HTTP Port, HTTPS Port, and RTSP Port. Contact your network administrator before changing port settings to ensure that your port settings do not conflict with your network infrastructure. Hostname 1. Click in the Hostname box and highlight the text. 2.
HTTPS Port NOTE: The HTTPS port is not configurable unless you have set SSL Mode to Optional or Required and installed a security certificate. 1. Click in the HTTPS Port box and highlight the text. 2. Type the new port number in the HTTPS Port field. The default port for HTTPS communications is 443. 3. Click Save. If you have changed the setting in error, you can click reset to revert to the previously saved setting. RTSP Port 1. Click in the RTSP Port box and highlight the text. 2.
Configuring IPv6 Settings Your Sarix device supports IPv6 in conjunction with IPv4 configurations; the device does not support IPv6-only network deployments. The device will accept up to sixteen IPv6 addresses, three IPv6 DNS servers, and three IPv6 gateways. There are two configuration modes for IPv6 address assignments: Auto: Enables automatic configuration using router advertisement. Additional configuration can be provided over DHCPv6 (if available on your network).
FIGURE 3-10: SSL CONFIGURATION SSL Configuration Select one of the following modes: Required: A signed Secure Sockets Layer (SSL) certificate must be installed, and a secure URL that begins with the protocol name “https:” must be used to access the camera. Sensitive data is always encrypted during transmission. A URL that begins with the “http:” protocol rather than the “https:” protocol will be redirected to the secure URL automatically. NOTE: Beginning with firmware version 1.8.
2. Select the “Generate Self-signed Certificate” option, and then click Next. The “Self-signed Certificate Information Form” opens. FIGURE 3-12: GENERATING SELF-SIGNED CERTIFICATE CONFIGURATION 3. Fill in all of the fields, and then click Generate Certificate. The following progress message appears on the page: “Loading data…” After a while, the certificate is uploaded to the device. 4. After the certificate is uploaded, select the desired mode. 5. Click Save.
Upload Certificate 1. Click the Install New Certificate button located at the bottom of the SSL Configuration page. The Select Certificate Install Method option buttons appear on the page. 2. Select Upload Certificate, and then click Next. The “Certificate” opens. FIGURE 3-14: UPLOAD CERTIFICATE 3. Choose the Certificate you want to upload and then click Upload button. The following progress message appears on the page: “Loading data…” 4.
3.2.2.4 802.1x 802.1x is a port security that authenticates devices that want to establish a point-to-point access through a wired or wireless port using Extensible Authentication Protocol (EAP). This port-based authentication method prevents unauthorized access to a Local Area Network (LAN) through a physical port. For example, when a device is connected to a network port, the network switch will ask the device for authentication.
SNMP Configuration WARNING: The Simple Network Management Protocol (SNMP) settings are advanced controls. Consult your network administrator to obtain the required information to configure SNMP settings. No SNMP Server None disables the SNMP configuration and is the default setting. CONFIGURING SNMP V2C 1. Select V2c as the SNMP Version. 2. Type the community name in both the Read and Write Community String box. The default name for each is “public” and “private” respectively. 3. 4.
3.2.2.6 Firewall Set the Firewall function. A firewall is a system or group of systems that manages access between two networks. FIGURE 3-18: FIREWALL CONFIGURATION Firewall 1. Select Allow or Deny mode to enable this function. The default setting is Off. 2. Check Enabled to enter IP address in the Address field. Up to ten addresses can be enabled for entry. 3. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it. 3.2.2.
3.2.2.8 VMS Connectivity This page relates to the standard protocol that conforms to the regulations of IP security surveillance data transmitting, transferring and monitoring within the PRC (People Republic of China) areas. FIGURE 3-20: VMS CONNECTIVITY SETTINGS GB/T-28181 Settings 1. Select the Enable check box to activate the VMS Connectivity function. 2. Enter an address for Server Address and a value for Port ranging from 1025 – 65535. 3.
3.2.3 Imaging Use the Imaging tab to change the camera’s general image settings, adjust the camera exposure and white balance, program the focus mechanism, or define window blanking privacy areas. FIGURE 3-21: IMAGING SETTINGS 3.2.3.1 General General imaging settings include adjustments for camera orientation and digital processing.
Orientation Use this setting when installing the camera in an inverted position. If the orientation is not adjusted, the image will display upside down and mirrored. Select one of the following options: 1. Click the “Flip left-to-right” box to rotate the camera image 180 degrees horizontally. 2. Click the “Flip top-to-bottom” box to rotate the camera image 180 degrees vertically.
3.2.3.2 Exposure Exposure is the amount of light detected by the camera sensor. A scene with correct exposure settings has adequate detail and contrast between white and dark values. An image with too little or too much exposure eliminates detail in the scene. The camera features Exposure and Day/ Night settings. FIGURE 3-23: EXPOSURE SETTINGS Exposure Priority Preset Select Motion or Low Noise as the exposure priority. The Motion setting increases exposure time to reduce motion blurring in low light.
Day/Night The Day Night Auto mode setting automatically controls the IR cut filter depending on the Transition Level and Transition Detect Time settings. Auto 1. Transition Level: Determines when the camera changes from day mode (color) to night mode (black-white). Select the “Lighter” transition level setting if you want the camera to change modes at a high lux setting. Use the “Default” setting for normal day/night operation. Use the “Darker” transition level to change modes at a low lux setting.
3.2.3.3 White Balance Under White Balance, choose from ATW (auto tracing white balance), Auto, and Manual modes of adjustment on white balance for the video. ATW offers continuous adjustments on camera color balance in accordance with any change in color temperature. Auto enables automatic controls on color temperature ranging from 2500°K to 10000°K.
3.2.3.4 Focus Focus sets the back focus to the center focal point of the scene. The camera can be configured to back focus automatically or manually. Auto focus automatically back focuses the camera on the subject in the center of the scene. Manual focus turns off the auto focus mechanism and locks the camera at a user-specified position. The manual focus setting is recommended only for indoor applications that have a single, unchanging primary light source.
FIGURE 3-27: MANUAL FOCUS SETTINGS 1. Day Manual Focus Position: If you need to fine-tune the daytime focus, slightly move the Day Manual Focus Position slider to the left or right. 2. Night Manual Focus Position: If you need to fine-tune the nighttime focus, slightly move the Night Manual Focus Position slider to the left or right. 3. If required, click the Restore Settings to Defaults button to reset the focus to the factory default setting.
3.2.3.5 Window Blanking Window blanking is used to conceal user-defined privacy areas. A blanked area appears on the screen as a solid gray window. The camera can handle up to 8 blanked windows as long as the total blanked area does not exceed 50 percent of the field of view. FIGURE 3-28: WINDOW BLANKING SETTINGS Window Blanking Window Blanking On 1. Draw a window in the Live Preview area of the page: a Hold down the left mouse button. b Drag the mouse diagonally across the area you want to blank.
NOTE: Up to 8 blanked windows can be defined, but the blanked area cannot exceed 50 percent of the field of view. 2. To resize the window, click and drag one or more of the points until the window is the desired shape and size. 3. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it. Deleting a window blanking area 1.
3.2.4 A/V Streams Use the A/V Streams tab to configure the video and audio streams for the camera. The A/V Streams tab includes a Video Configuration page and an Audio Configuration page as well as the Local Recording page. FIGURE 3-30: A/V STREAMS 3.2.4.1 Custom Video Stream Configuration The Video Configuration page allows you to customize the compression, resolution, image rate, and bit rate of the video streams. The default names for the streams are Primary Stream and Secondary Stream.
FIGURE 3-31: CUSTOM VIDEO STREAM CONFIGURATION Select Preset Presets are fully-configured video configurations that offer a good balance of video performance to bandwidth. These presets may also be used as a starting point for a custom configuration. Choose to switch the Corridor Mode On or Off. Corridor Mode offers a vertically widened field of view in narrow spaces like hallways and tunnels. NOTE: Corridor mode is not available when codec is MJPEG.
TABLE 3-2.
Rate Control The rate control setting determines the bit rate and quality of each frame in the video stream. CBR: The constant bit rate (CBR) streams video at a fixed number of bits per second. CBR uses the full capacity of the bit rate setting for scenes with or without motion. Video is always streamed at the user bit rate setting. Adjust the CBR Bit Rate slider that appears when CBR is selected to the optimal fixed number of bits per second.
3.2.4.2 Audio Configuration The Audio Configuration page allows you to setup the audio device. The default setting for Audio is disabled, which means that no audio is transmitted from the camera. When enabled, audio is transmitted from the camera to the PC. Based on your system configuration, images and audio may not be synchronized. NOTE: Improper use of audio/visual recording equipment may subject you to civil and criminal penalties.
3.2.5 Users Use the Users tab to create and manage user accounts and to change the way the camera manages the user settings. FIGURE 3-34: USERS CONFIGURATION 3.2.5.1 General Settings Use the General Settings page to set the public user access level. This access level is a predefined set of user permissions that allows the camera to be accessed without logging on. Available permission levels depend upon the model of the device that you are using.
User and Group Management Sarix cameras support two methods for managing the permissions of users and groups. Local Mode The camera manages users and groups locally. This is the default setting. Remote Mode The camera authenticates and manages users through an LDAP server supported by Microsoft® Active Directory®. This allows administrators to tie cameras and group permissions into existing single sign-on services (SSO). Selecting Remote Mode disables local user management settings.
3. b Input the CN and DN for the group of users to whom you want to grant manager access in the Managers box. c Input the CN and DN for the group of users to whom you want to grant operator access in the Operators box. d Input the CN and DN for the group of users to whom you want to grant viewer access in the Viewers box. A user must be authenticated by the remote server prior to entering remote mode.
Username Click in the Username box and type a user name (2 to 23 alphanumeric characters). User names are case-sensitive. Password Click in the Password box and type a password (4 to 16 alphanumeric characters). Passwords are case-sensitive. Re-type Password Click in the Retype Password box and retype your password.
3.2.6.1 Alarm Source This page allows user to configure the settings of the connected alarm input source, which is the external alarm signaling device, such as a door contact or motion detector. Both normally open and normally closed devices are supported. FIGURE 3-39: ALARM SOURCE Alarm Input Settings 1. Check Enabled button to enable Alarm Input. 2. Select either Normally Open or Normally Closed from the Polarity drop-down menu.
FIGURE 3-41: MOTION ZONE AREA ENABLING 5. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it. 3.2.6.3 Sabotage Detection The Camera Sabotage behavior detects scene changes or contrast changes in the field of view. An event or alarm is triggered if the lens is obstructed by spray paint, a cloth, or if it is covered with a lens cap. Any unauthorized repositioning of the camera also triggers an event or alarm.
3.2.6.4 Audio Detection This function is designed to define the detailed settings for triggering surrounding audio detection. Check to have this function enabled. Under Sound Intensity Threshold, adjust the threshold bar or input a number in the box right under it for the desired threshold level. A horizontal line, which indicates the exact threshold, in the box underneath will move up or down accordingly. FIGURE 3-43: AUDIO DETECTION 3.2.6.
4. Password: Input the password associated with Username. NOTE: The default Username and Password are “guest” and “1234”. Settings 1. Set Pre-event Snapshots, Post-event Snapshots, Pre-event Snapshot Interval, and Post-event Snapshot Interval for Alarm, Motions 1 through 4, Sabotage Detection, Schedule, and Audio Detection selected. 2. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.
3.2.6.6 Relay Open/Close Handler Define the relay related settings for alarm output device when a selected event is triggered under this page. The connected relay external device can be activated by the method of Normally Open or Normally Closed. FIGURE 3-47: RELAY OPEN/CLOSE HANDLER SETTINGS Relay Open/Close Handler 1. Check any or all of the Alarm, Motion 1 through 4, Sabotage Detection and Audio Detection options from the Enabled section to activate relay handler when any of the selected events occur.
3.2.6.7 SD Record Handler Save video clip backups from a variety of activated events to an SD card. Before using this function, a SD card must be installed in the camera beforehand. NOTE: The SD card must be formatted as FAT32. Other formats are not compatible with the camera. FIGURE 3-48: SD RECORD HANDLER SETTINGS 1. Check to enable SD Record Handler for Alarm, Motions 1 through 4, Wire Network Lost, Sabotage Detection, and Audio Detection. 2.
Format SD card as FAT32 1. Double click guiformat.exe, the FAT32 Format window will pop up as the figure shows below. 2. Select the hard disk/SD card you want to format as FAT32 from the Drive drop-down menus, and then click Start button to begin format the hard disk/SD card. NOTE: Format will erase all information off of the hard disk/SD card. Make sure you have any important files backed up before you format it. FIGURE 3-49: FAT32 FORMAT 3.
3.2.6.8 SMTP Notification Handler Set detailed SMTP Notification Handler function that will send an email to predefined email addresses when any or all the selected events are activated. NOTE: To use email notification, the camera must be connected to a local area network (LAN) that maintains an SMTP mail server. Consult your network administrator for information on configuring email notification on your local network. FIGURE 3-51: SMTP NOTIFICATION HANDLER SETTINGS SMTP Notification Handler 1.
SMTP Server Set up Simple Mail Transfer Protocol (SMTP), the Internet standard for electronic mail (e-mail) service across Internet Networking, related settings under this section. 1. Host Address: Input a server name or address. 2. Port: set “25” as default or change to dedicated number. 3. Username: Input a user name with privilege to access the server. 4. Password: Input the password associated with Login ID. 5. Authentication: Select an authentication type.
3.2.6.9 Sound Notification Handler This page is designed for configuring detailed settings for sound notifications when an event occurs. FIGURE 3-52: SOUND NOTIFICATION HANDLER SETTINGS Sound Notification Handler 1. Select the level ranging from High, Mid to Low for sound notification handlers of different events. 2.
Pelco Troubleshooting Contact Information If the instructions provided fail to solve your problem, contact Pelco Product Support at 1-800-289-9100 (USA and Canada) or +1-559-292-1981 (international) for assistance. Be sure to have the serial number available when calling. Do not try to repair the unit yourself. Leave maintenance and repairs to qualified technical personnel only.
