® IOP19C4C Integral Camera and Lens for SB1900 Series Preset Domes Installation/Operation Manual C720M (1/96) PELCO • 3500 Pelco Way, Clovis, CA 93612-5699 • (1-209) 292-1981 • (800) 289-9100 FAX (800) 289-9150 or (1-209) 292-3827
TABLE OF CONTENTS Section Page 1.0 WARNINGS ........................................................................................................................................1 2.0 SCOPE ...............................................................................................................................................1 3.0 DESCRIPTION ................................................................................................................................... 1 4.
LIST OF ILLUSTRATIONS Figure 1 2 3 4 5 6 7 8 Page TVH6 Series Camera Dimensions .................................................................................................. 1 IOP Package Installation ................................................................................................................. 2 Wiring Diagram for SB1900 Preset Dome and IOP Package With Presets .................................... 3 Schematic Diagram for Color Camera/Lens ...........................................
(This page intentionally left blank.
INSTALLATION/OPERATION MANUAL MODEL IOP19C4C INTEGRAL CAMERA & LENS PACKAGE FOR SB1900 SERIES PRESET DOMES 2.0 SCOPE The information contained in this manual covers the IOP019C4C integral camera and lens package for the SB1900 Series preset domes. 3.0 DESCRIPTION 1.0 WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes. 2.
4.0 INSTALLATION CAUTION: Make certain not to drop or jar the camera and lens combination or damage will result to the unit. To install the camera and lens package in your dome, please follow the steps outlined below. Refer to Figure 2, if necessary. 1. Disconnect main power to back box. 2. Remove dome drive from back box. 3. Insert the two (2) 1/4-20 studs on the IOP package through the slots in tilt table with the IOP facing the front of the tilt table.
Figure 3.
5.0 ELECTRICAL WIRING See Figure 4 below for wiring diagram of the IOP19C4C camera and lens module.
6.0 ADJUSTMENTS Your optics package comes factory adjusted for a broad range of lighting conditions. For this reason, you may find it necessary to adjust your optics package to tailor the picture to your specific viewing environment. The following adjustments can be made to the Pelco optics package.
6.4 WHITE BALANCE (ATW/AWB SWITCH) White balance is a feature available on the color optics packages. In the ATW (Automatic Tracing White Balance) position, the white balance is continuously adjusted to take into account variations in the incident light conditions. In the AWB (Automatic White Balance) position, when the “LOCK” button is pressed, the white balance is automatically adjusted, and the setting is stored in memory.
SHUTTER SPEED ADJUSTMENTS MAY BE PERFORMED BY USING A SMALL STANDARD SCREWDRIVER AND MOVING THE ROTARY SWITCH AS SHOWN. “0” POSITION IS FACTORY DEFAULT. SEE FIGURE 7 FOR SETTING VALUES V-PHASE BUTTONS (MOMENTARY PUSH-BUTTON) ADVANCE AND RETARD THE PHASE INTERVAL WITH RESPECT TO ZERO CROSSOVER OF AC LINE ±90° THIS MOMENTARY BUTTON LOCKS AWB AGC (AUTOMATIC GAIN CONTROL) IS SET IN THE ON POSITION (SHOWN) Figure 6.
LOCK ON V PHASE V-PHASE BUTTONS USED IN CONJUNCTION WITH AWB POSITION OF WHITE BALANCE SWITCH.
7.0 EXPLODED ASSEMBLY DRAWING If necessary, refer to Figure 8 for an exploded assembly drawing and parts list. Figure 8. TVH6 Series Camera/Lens Combination Exploded Assembly Drawing 7.1 PARTS LIST FOR FIGURE 8, TVH6 SERIES Item 1 2 3 4 5 6 7 8 A B C D E F G H J K Qty 1 1 — 1 1 1 1 1 — 1 2 5 5 16 2 2 2 4 Pelco Manual C720M (1/96) Description Lens, 1/2" motorized zoom, 8.5-51, f1.
8.0 MODELS IOP19C4C High resolution color PAL (CCIR) series camera with integral 6X motorized zoom lens with presets. 9.0 SPECIFICATIONS MECHANICAL Mounting Bracket Construction: Dimensions: 0.
10.0 WARRANTY AND RETURN INFORMATION WARRANTY RETURNS Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex® Series products (multiplexers, server, and keyboard).
® PELCO 300 West Pontiac Way Clovis, CA 93612-5699 USA (209) 292-1981 • (800) 289-9100 FAX (800) 289-9150 or (209) 292-3827 DataFAX (800) 289-9108 or (209) 292-0435 International customers call 1-209-292-1981 or FAX 1-209-348-1120 (Product specifications subject to change without notice.
