I N S T A L L A T I O N IXE Series Network Box Cameras Sarix® Cameras with SureVision Technology C2271M (9/13)
Contents Important Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Legal Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Regulatory Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Video Quality Caution. . . . . . . . . . . . . .
List of Illustrations 1 2 3 4 5 Camera Connections and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Lens Pin Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Cable Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Alarm/Relay Port Pins . . . . . . . . . . . . . . .
Important Notices LEGAL NOTICE SOME PELCO EQUIPMENT CONTAINS, AND THE SOFTWARE ENABLES, AUDIO/VISUAL AND RECORDING CAPABILITIES, THE IMPROPER USE OF WHICH MAY SUBJECT YOU TO CIVIL AND CRIMINAL PENALTIES. APPLICABLE LAWS REGARDING THE USE OF SUCH CAPABILITIES VARY BETWEEN JURISDICTIONS AND MAY REQUIRE, AMONG OTHER THINGS, EXPRESS WRITTEN CONSENT FROM RECORDED SUBJECTS.
OPEN SOURCE SOFTWARE NOTICE This product includes certain open source or other software originated from third parties that is subject to the GNU General Public License (GPL), GNU Library/Lesser General Public License (LGPL) and different and/or additional copyright licenses, disclaimers, and notices. The exact terms of GPL, LGPL, and some other licenses are provided to you with this product. Please refer to the exact terms of the GPL and LGPL at http://www.fsf.org (Free Software Foundation) or http:// www.
Introduction The Sarix® IXE Series IP cameras feature SureVision technology that seamlessly delivers advanced low-light performance with wide dynamic range (WDR) and anti-bloom technologies that operate simultaneously. They are part of Pelco’s Enhanced (E) range of cameras, providing industry-leading image quality and performance. The IXE Series box camera is easy to install, offers flexible mounting options, and uses a standard Web browser for easy remote setup and administration.
MODELS IXES1 Sarix 0.5 MPx with SureVision, low-light, WDR, day-night, network camera with built-in Pelco analytics IXE11 Sarix 1.
Getting Started Before installing your device, thoroughly familiarize yourself with the information in the installation section of this manual. NOTES: • Pelco recommends connecting the device to a network that uses a Dynamic Host Configuration Protocol (DHCP) server to address devices. • Do not use a network hub when configuring the network settings for the device. • To ensure secure access, place the device behind a firewall when it is connected to a network.
Product Overview Figure 1. Camera Connections and Features ì Accessory Port: Connects with compatible Pelco accessories. î Ethernet Activity/Link LED: Flashes yellow to indicate that data is being transmitted or received by the camera. ï RJ-45 Network Port: Connects the camera to the IP network. Also supplies power to the camera (PoE), through the same connector. ñ Reset Button: Reboots the camera or restores the camera’s factory default settings. This button is recessed.
Installation CAUTION: Hot Surface! Always turn off power and allow the unit to cool prior to handling. Failure to follow these instructions can result in injury. NOTE: Pelco megapixel (MPx) lenses have been designed and tested to deliver optimal image quality for the IXE Series camera. The use of a standard definition lens or any other lens not tested by Pelco on an IXE Series MPx camera could limit the resolution of the camera, creating poor image quality. 1. Install the lens. a.
4. Apply power to the camera. The camera will complete a configuration sequence. The LED at the front of the camera will glow solid amber during the configuration sequence and then blink green for several minutes. The LED will turn solid green after the sequence is complete. NOTE: If the camera is not connected to a DHCP server and DHCP is enabled, the configuration sequence can take several minutes to complete. 5. View the camera image by finding the camera’s IP address on a Web browser.
Wiring ETHERNET WIRING REQUIREMENT FOR POE Connect a Cat5 cable or higher (Cat5e, Cat6) cable (not supplied) to the RJ-45 network connector. The 8-pin port includes video over Ethernet, and PoE for the camera. PoE (IEEE 802.3af, Class 3) injects power over the same cabling that carries the network data, eliminating the need for a separate power supply. This simplifies the installation and operation of the camera without affecting network performance.
ALARM/RELAY PORT The 5-pin Alarm/Relay port has the following pins and pin assignments. PIN 5 PIN 1 Figure 4. Alarm/Relay Port Pins Table B. Pin Descriptions for Alarm/Relay Port Pin C2271M (9/13) Function 1 Alarm Ground 2 Alarm Input 3 Ground 4 Relay N.O.
AUDIO PORT The 4-pin Audio port has the following pins and pin assignments. PIN 1 PIN 4 Figure 5. Audio Port Pins Table C.
IP Address Settings If the camera is connected to a Dynamic Host Configuration Protocol (DHCP) network and DHCP is set to On, the server automatically assigns an IP address to the camera. The default setting for the camera is DHCP On. To set the camera’s IP address manually, set DHCP to Off. NOTES: • If the camera is not connected to a DHCP server but DHCP is set to On, the default IP address 192.168.0.20 on subnet mask 255.255.255.0 is automatically assigned to the camera.
Specifications CAMERA Imaging Device 1/3-inch Imager Type CMOS Imager Readout Progressive scan Maximum Resolution 3 MPx (2048 x 1536) 2 MPx (1920 x 1080) 1 MPx (1280 x 1024) 0.5 MPx (800 x 600) Signal-to-Noise Ratio >60 dB Auto Back Focus Yes Electronic Shutter Range 1 ~ 1/77,000 sec True Wide Dynamic Range Up to 100 dB* White Balance Range 2,000° to 10,000°K Sensitivity Color (33 ms) Color (500 ms) Mono (33 ms) Mono (500 ms) f/1.2; 2,850°K; SNR >20 dB 0.1 lux 0.005 lux 0.05 lux 0.
ENVIRONMENTAL Operating Temperature –10° to 50°C (14° to 122°F) Storage Temperature –10° to 60°C (14° to 140°F) Operating Humidity 20 to 80%, RH noncondensing Storage Humidity 20 to 80%, RH noncondensing AUDIO Streaming Bidirectional: full or half duplex Input/Output Line level/external microphone input; 600-ohm differential, 1 Vp-p max. signal level; built-in microphone Compression G.
NETWORK Supported Protocols TCP/IP, UDP/IP (Unicast, Multicast IGMP), UPnP, DNS, DHCP, RTP, RTSP, NTP, IPv4, IPv6, SNMP v2c/v3, QoS, HTTP, HTTPS, LDAP (client), SSH, SSL, SMTP, FTP, ARP, ICMP, and 802.1x (EAP) NOTE: IPv6 protocol supports mixed IPv4 and IPv6 installations, but not IPv6-only deployments. Users Unicast Multicast Up to 20 simultaneous users depending on the resolution settings Unlimited users H.
REVISION HISTORY Manual # C2271M Date 9/13 Comments Original version. Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. All other product names and services are the property of their respective companies. ONVIF and the ONVIF logo are trademarks of ONVIF Inc. Product specifications and availability are subject to change without notice. © Copyright 2013, Pelco, Inc. All rights reserved.
Pelco by Schneider Electric 3500 Pelco Way Clovis, California 93612-5699 United States USA & Canada Tel (800) 289-9100 Fax (800) 289-9150 International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120 www.pelco.com www.pelco.
