NET5501-I VIDEO ENCODER Installation/Operation Manual C5650M-B (05/15)
Copyright All rights reserved. No part of this manual may be reproduced, distributed, or transmitted without the prior written permission of the manufacturer.
Content Overview 4 4 Important Safety Instructions 6 Important Notices 5 8 8 8 9 10 11 Installation 12 Web Viewer 18 Legal Notice (Audio Notice) Introduction Package Contents Front Panel Description Rear Panel Description Wall Bracket Installation 14 Connecting to an External Device 13 Factory Default 18 What is the Web Viewer? 23 System Setting 21 26 29 32 34 35 36 Network Topology Statement 12 31 Appendix Caution Live Network Setting Camera Configuration A/V Streams Setti
Overview Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Caution This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. English |5 Overview WARNING : This product is sensitive to Electrostatic Discharge (ESD). To avoid ESD damage to this product, use ESD safe practices during installation. Before touching, adjusting or handling this product, correctly attach an ESD wrist strap to your wrist and appropriately discharge your body and tools.
Overview Important Notices REGULATORY NOTICES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules.
OPEN SOURCE SOFTWARE This product includes certain open source or other software originated from third parties that is subject to the GNU General Public License (GPL), GNU Library/Lesser General Public License (LGPL) and different and/or additional copyright licenses, disclaimers, and notices. This offer is valid for a period of three (3) years from the date of the distribution of this product by Pelco. CCC POWER CORD STATEMENT Models shipped to China do not include power cords.
Overview Network Topology Statement IMPORTANT NOTE. PLEASE READ. The network implementation is shown as a general representation only and is not intended to show a detailed network topology. Your actual network will differ, requiring changes or perhaps additional network equipment to accommodate the system as illustrated. Please contact your local Pelco representative to discuss your specific requirements.
Package Contents Resource Disc 4-Pin Terminal Block (1ea) Screw (2ea) for Wall mounting Anchor (2ea) for Wall mounting Wall Mount Bracket (1ea) Screw (4ea) for Wall bracket binding 2 plus 2 spare English |9 Overview Installation Manual, Safety Instruction (2ea)
Overview Front Panel Description a No. b Name c Description RS-422 RX Data line RX+/RX- JJ Disabled in RS-485 mode. a TX+/TX- RS-422/RS-485 Data line Video input BNC terminal. b 1 Displays power On/Off status. It glows blue when the unit has power. Displays network status (connection and speed). 1 Off : The unit is not connected to the network. Solid amber : The unit is connected to the network using the 100 Mbps standard.
Rear Panel Description POE Overview A NO COM Tx+ Rx+ a No. Name 1 Description Press this switch to reset device to the factory default. 1 please see Factory If you perform the factory reset, all your settings to device will be lost. For more information, NCDefault Tx- Rx- (Page 13). a b b PoE Connects to the network and supplies power through Ethernet cable.
Installation Wall Bracket Installation 1. Align the product with the bracket holes. Insert and tighten the provided screws to attach the product to the bracket. drill bit of 5 mm (0.20 in.) diameter and drill on the marked positions, drill to have 3 cm (1.18 in.) deep holes. Clean the holes 2. Use after drilling. 3. Insert an anchor for each hole. Fully insert anchors by lightly hammering the anchor head with a hammer/rubber hammer. 4.
Factory Default POE Installation 1. Press and hold the Reset switch with a pointed object such as a paper clip before powering on. 2. Power on. 3. Release the Reset switch when the power LED [ ] on the top panel is turned on. (about 8 seconds). 4. When the encoder reset is completed, the system will restart by the factory default.
Installation Connecting to an External Device Connecting the Video Connect the [ ] port of the encoder to the video output port of the camera. 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Camera Connecting the terminal block The terminal block has tension clamps instead of screw terminals. Use a small screwdriver to open the clamp for a particular lead.
Connecting the RS-422/RS-485 Device Connect the external device to the [RS-422/RS-485 Data line] ports. You can connect and control PTZ camera that supports RS-422/RS-485 communication.
Installation Network Connection PC Connection in the Local Network You can connect the encoder to a PC in the same network and control or manipulate it on the PC monitor. POE Broadband router Local PC 1. Camera Local PC Connect the network port in the rear panel to the router or hub. POE PWR RESET WAN 4 3 2 Local PC 1 Broadband router Local PC 2. Connect the local PC to the router or hub.
PC Connection From a Remote Network You can connect the encoder to a PC or mobile device in the same remote network and control or manipulate it on the monitor of the PC or mobile device POE Local PC 1. Installation Broadband router Internet Internet Local PC Local PC Connect the network port in the rear panel to the router. POE PWR RESET ADSL modem WAN 4 3 2 1 Broadband router Local PC 2.
Web Viewer What is the Web Viewer? Minimum PC Requirement CPU P4 3.0 or Higher RAM 512MB or Higher VGA GeForce MS 400, Radeon 7500 or higher GeForce 8 series or higher VGA MEMORY 64MB MONITOR 1280 X 1024 BROWSER Internet Explorer, Firefox, Chrome, Safari IE VERSION IE8.0 or higher NETWORK 10/100 Bps Accessing the Encoder and Attached Cameras The first time you access the camera, the live video page appears.
Pelco Media Player Installation To view videos after accessing the Web viewer, the Pelco Media Player plug-in must be installed. Install Pelco Media Player from the CD included with the player. The Pelco Media Player 1.9.5 or higher is required for multiple channels. Web Viewer 1. Run InstallPelcoMediaPlayer.msi. 2. Click the [Next>] button to start installation. the [Close] button. 3. Click Pelco Media Player Installation is complete.
Web Viewer Logging In Entering the IP address of the camera as a URL into the web browser will immediately bring up the Live Mode screen if the encoder is not setup to require authentication (Open Authentication option). If the camera is setup to require authentication, then the user will be prompted for a Username and Password before being able to see the live video feed. 1. Click on the live screen. 2. Enter your and . Default username : admin, Password : admin 3.
Live Live Screen Overview Live Mode Screen Components a b c d e f Web Viewer i j g k l m h No. Name Description a Channel Name Displays the name assigned to the channel selected. b Multi-Function Image Button $ Tilt Up % Tilt Down + Pan Right _ Pan Left Home Preset c Control the Zoom Activates Zoom in (-) / Zoom out (+) features. d Control the Focus Activates Near (-) / Far (+) features. e Control the Iris Adjusts the camera brightness.
Web Viewer No. Name Description h Stream Selection Selects the viewable video stream that displays in live view (Primary, Secondary, QuickView) and selects unicast or multicast and throttle settings. i View the Selected Tab Composed of Live, Settings, Help, and Logout settings menus. j Maximize Viewing Area Scales the image to the full size of the browser. To resize the video pane to normal view, click the Show Toolbar button in the upper-right corner of the window.
System Setting General Settings Modify the system default settings of the encoder. General Settings Web Viewer ~~ Device Name : Set the name to use for the encoder. The device name must be at least two (2) characters and no more than 63 characters. Time Settings ~~ Time Server : Set the time to apply to the encoder. -- None : Specify no time setting for the encoder. -- DHCP : Specify the time from the DHCP server.
Web Viewer Analog Input You can set the type of the encoder analog video output. Analog Video Input Standard Set the video output type. ~~ Auto : Automatic conversion according to the video input type connected. ~~ NTSC : Select to force the video mode if the transfer method supports NTSC. ~~ PAL : Select to force the video mode if the transfer method supports PAL. Backup & Restore You can backup or restore settings. The system will restart automatically after backup or restoration.
Restore Backup Settings 1. Click the [Browse...] button to restore backup settings. 2. Select the desired backup file and click the [Open] button. 3. Click the [Upload and Restore] button. Web Viewer Information Check the encoder’s system information. Firmware You can upgrade the encoder’s firmware.
Web Viewer Network Setting General Modify the network default settings of the encoder. System Settings Set the system hostname and port. ~~ Hardware Address : Presents the MAC Address of the encoder device. ~~ Hostname : A user-friendly name into the Hostname box (1 to 21 characters) using alphanumeric characters should be specified. A user-friendly name makes it easier to recognize the device on the network. Numeric-only names are not allowed.
SSL You can either select the security access method for the encoder or install an accreditation certificate. SSL Configuration Select a security access method. Web Viewer Certificate Install an accreditation certificate. To Install an Accreditation Certificate 1. Click . 2. Select a certificate to install. 3. Click . 4. Select the accreditation certificate and key file to install. 5. Click the button.
Web Viewer 802.1x When connected to a network, select 802.1x protocol to install the certificate. 802.1x Port Security ~~ Protocol : Specify the 802.1x protocol. ~~ Username : Enter the client certificate ID. ~~ Password : Enter the certificate key password. If the key file used is not encrypted, you don’t need to enter it. SNMP The system or network manager can use the SNMP protocol to monitor network equipment or operate environment settings and other tasks remotely.
Camera Configuration Choose number 1 to the number of channels on the encoder. General Setup the camera connected to the encoder. Web Viewer Digital Processing Adjust each camera channel video input. ~~ Saturation Adjust : Adjust video saturation. ~~ Contrast Adjust : Adjust video contrast. ~~ Brightness Adjust : Adjust video brightness. ~~ Hue Adjust : Adjust video tint. Click to restore the factory settings.
Web Viewer Configuration and operation for presets and patterns Patterns and presets can be configured directly from the OSD for third-party cameras that support these features. 1. Access the OSD from the Settings page. the arrow keys select Dome Settings, and then 2. Using press the Enter key. the arrow keys select Presets or Patterns, and then 3. Using press the Enter key. to program presets and patterns. Refer to the 4.
A/V Streams Setting Video Configuration Set the video streaming of the channel connected to the encoder. Select Preset Web Viewer Select a preset for seamless streaming. Primary Stream/Secondary Stream Select as preset to set up detailed settings Click to check the current video streaming information.
Web Viewer User Setting General Settings Set up user authentication mode and local/remote information. Authentication Mode Set public/private settings of the authentication mode. User and Group Management -- Local Mode : The default setting is local mode. Any changes to users and groups affect only the camera that you are accessing. -- Remote Mode : Set remote mode for users connected through LDAP or the Active Directory server. -- LDAP Server : Specify the IP address or hostname of the LDAP server.
Users Set up settings relating to user management and rights. To Add a User Account Web Viewer 1. At the bottom left screen click the button. 2. Select . ~~ Access Level : Set the rights for the account. -- Admins : Permissions include access to all camera settings. -- Managers : Permissions include access to all settings except this user cannot modify user permissions or restore factory default settings.
Web Viewer Events Setting Motion Detection You can select the event signal to be given if a movement is detected. To Set Motion Detection 1. Select Video Channel and Sensitivity. the mouse over the Live Preview screen and set the 2. Drag motion detection area. ~~ Select All : Select all areas. ~~ Deselect All : Deselect all areas. Sabotage Detection You can select the event signal to go off when tampering with a camera (covering the lens, change in camera position, etc.) is detected.
SMTP Notification Handler A message will be sent to the e-mail address registered in the SMTP server when an alarm is set off. Web Viewer Help Click the tab to check Web viewer information.
Appendix Product Specification SUPPLIED ACCESSORIES Power Adapter PoE Power Cord / AC PLUG - Terminal Block 4-pin terminal blocks x 1 Rack Mount / Wall Mount 1, Wall Mount Rubber Feet - Video Standards NTSC / PAL Video Encoding H.
FRONT PANEL INDICATORS Video presence Network status Unit status ENVIRONMENTAL Off : The unit is not connected to the network Solid amber : The unit is connected to the network using the 100Mbps standard Solid red : The unit is connected to the network using the 10Mbps standard Solid green : The unit is connected to the network using the 1Gbps standard The Pelco badge glows blue when the unit has power Green : The unit is functioning normally Red : The unit is in an error condition Operating Temperature
Appendix Troubleshooting (FAQ) Problem Action The product does not turn on in any way. ~~ If you use the PoE power, you can verify that you have sufficient power. No monitoring video is displayed at all. ~~ Check whether the video cable of the camera is connected properly. ~~ Check the power of the camera. ~~ Check the settings of the camera lens. I failed to connect the PC to the Encoder. ~~ Check whether the LAN cable and the hub are connected properly to the Encoder.
Product Overview Unit : cm (inch) 1(0.39) 2.5(0.98) 0.5(0.2) Appendix 8.5(3.35) 10(3.94) 10.4(4.1) 12.25(4.82) 3.2(1.26) 3.32(1.31) 5.6(2.2) NOTE : VALUES IN PARENTHESES ARE INCHES; ALL OTHERS ARE CENTIMETERS.
Open Source License Report on the Product The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. ~~ GPL Software : linux kernel, busybox, cdrtools, dvd+rw-tools, smartctl, uboot, bash, udev, sysklogd ~~ LGPL Software : glibc, vmstat, glib, gtk, libESMTP, iconv, gstreamer, pango, ~~ OpenSSL License : OpenSSL GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc.
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it.
Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an interactive mode: Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type ‘show w’. This is free software, and you are welcome to redistribute it under certain conditions; type ‘show c’ for details.
A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular programming language, one that is widely used among developers working in that language.
d) Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source in the same way through the same place at no further charge. You need not require recipients to copy the Corresponding Source along with the object code.
9. Acceptance Not Required for Having Copies. You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License.
15. Disclaimer of Warranty. THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.
The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based on the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term “modification”.
b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user’s computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with.
END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Libraries If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). To apply these terms, attach the following notices to the library.
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2012/19/EU of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment. REVISION HISTORY Manual # C5650M C5650M-A Date 07/14 10/14 C5650M-B 05/15 Comments Original version Changed power consumption values.
Pelco by Schneider Electric 3500 Pelco Way Clovis, California 93612-5699 United States USA & Canada Tel (800) 289-9100 Fax (800) 289-9150 International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120 www.pelco.com www.pelco.
