Installation/Operation PelcoNet™ Transmission System C1977M-D (6/02) Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.
CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ........................................................................................ 6 Regulatory Notices ............................................................................................................................ 6 INSTRUCTIONS FOR THE NETWORK ADMINISTRATOR ....................................................................... 7 The Transmitter and Receiver .......................................................................
WEB BROWSER CONTROL PAGES ....................................................................................................... 51 Accessing These Pages .................................................................................................................. 51 Controlling The Display ................................................................................................................... 52 Matrix Control Live Video/Server Push Page Contents ............................................
List of Illustrations Figure 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49a 49b 50 [4] Page Front Panel Connectors ............................................................................................................. 10 Rear Panel Connectors .............................................................................................................. 11 Connecting A Camera Or Monitor .......................
1 52 53 54 Using PelcoNet with CM6800 to Provide Remote Control ......................................................... 85 Manager Screen ......................................................................................................................... 86 Menu Screen .............................................................................................................................. 86 Using PelcoNet with CM6800 and KBD200 to Provide Remote Control ....................................
IMPORTANT SAFEGUARDS AND WARNINGS Observe the following warnings before installing and using this product. 1. Installation and servicing should be done by qualified service personnel only and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture. 3.
INSTRUCTIONS FOR THE NETWORK ADMINISTRATOR The PelcoNet™ Transmission System allows live video transmission to be viewed over TCP/IP-based networks. This section is intended to help the network administrator know what is involved with installing this product and how it will affect the network. The person installing the product will need the following information about the network to make the product function properly.
WHAT IS THE PELCONET TRANSMISSION SYSTEM? The PelcoNet Transmission System is a new technology that lets you view video in real time across a Local Area Network (LAN) and even Wide Area Networks (WAN). This technology is based on the TCP/IP protocol suite and Ethernet technology, providing compatibility with today’s networking standards. (See the Glossary section for definitions of terms used in this manual.
OVERVIEW NOTE: This manual refers to the PelcoNet Transmission System unit when discussing features, functions, or specifications that apply to both transmitter and receiver models. “Receiver,” as used in this manual refers to a PelcoNet Transmission System receiver unless otherwise noted. Description The PelcoNet Transmission System lets you transmit and receive live video, audio, and data over existing Ethernet computer networks (either intranet or Internet) using the TCP/IP protocol.
Front Panel Connectors The PelcoNet Transmission System uses a compact design. One reason for the compact design is that connectors are placed on both the front and rear panels. The front panel connectors are dedicated to the media interfaces (video, audio, and data). They are shown in Figure 1.
Rear Panel Connectors The network interface, a terminal port for configuration and management, an alarm I/O-port, and the power connector reside on the unit’s rear panel (see Figure 2).
QUICK INSTALLATION GUIDE Follow the next seven steps for the fastest way to get your product up and running. Step 1: Connecting A Camera Or Monitor 1 3 2 4 Key: 1 = 2 = 3 = 4 = Camera or other video source with composite PAL or NTSC output Video monitor with composite PAL or NTSC input Transmitter Receiver Figure 3.
Step 3: Connecting To The LAN Port 1 2 3 Key: 1 = Ethernet (10BASE-T) LAN connection to hubs, network, PCs (RJ-45 connector) 2 = Ethernet Cat5 cable 3 = Transmitter or receiver Figure 4. Connecting To The LAN Port To connect to the Ethernet network, use a standard UTP Cat5 cable with RJ-45 connectors. Plug this cable into the RJ-45 receptacle labeled “Ethernet/UTP” at the rear of the unit. The connection to a 10BASE-T network can be made directly via a hub or switch.
Step 5: Selecting An IP Address For Your Network NOTE: Consult your network administrator for a valid IP address. The transmitter comes with the default address 192.168.0.1 while the receiver’s default address is 192.168.0.2. Before operating the system inside your own network, you need to set a valid IP address. Use a terminal program attached at the RS-232 control terminal port to change the IP address.
Figure 6.
Displaying Video Via a Transmitter-To-Receiver Connection LAN/WAN TCP/IP INTRANET/INTERNET RECEIVER TRANSMITTER MONITOR CAMERA Figure 7. Configuration For Box-To-Box Connections There are two ways to make a high performance multimedia transmission system for computer networks: • One way is to use just the transmitter and connect it through the computer network to a PC with a web browser at the receiving end. • Another way is to connect the transmitter through the computer network to a receiver.
Diagrams of Typical Applications Server Hub PelcoNet Receiver PelcoNet Transmitter Audio Audio Data Data Monitor Camera Figure 8. LAN Box-To-Box Connection (Transmitter, Receiver, Fixed Camera) Server Hub PelcoNet Receiver PelcoNet Transmitter Video Audio Audio PV130 Data Data PV130 Monitor F2 F3 7 8 CAM 0 Keyboard PRESE T MACRO Spectra II Figure 9.
Server Hub PelcoNet Transmitter Camera Browser Figure 10. LAN Browser-To-Box Connection (Transmitter, Browser, Fixed Camera) Server Hub PelcoNet Transmitter Video Data PV130 Browser Spectra II Figure 11.
Server Hub PelcoNet Transmitter Data Video PV130 PELCO GENEX Genex Browser Spectra II Figure 12. LAN Browser-To-Box Connection (Transmitter, Browser, Spectra II, Genex®) Clovis Server 1or more PCs Router Hub PelcoNet Receiver Audio Monitor Video 1or more PCs New York Server Router Hub PelcoNet Transmitter Video Audio Camera Figure 13.
1or more PCs Clovis Server Router 1or more PCs New York Server Router Hub Hub PelcoNet Receiver PelcoNet Transmitter Video Audio Audio Video Data PV130 Data PV130 Monitor F2 F3 7 8 CAM PRESE T 0 MACRO Spectra II Keyboard Figure 14.
Clovis Server 1or more PCs Router 1or more PCs New York Server Router Hub Hub PelcoNet Transmitter Video Video Browser Camera Figure 16. WAN Browser-To-Box Connection (Transmitter, Browser, Fixed Camera) Clovis Server 1or more PCs Router Hub 1or more PCs New York Server Router Hub PelcoNet Transmitter Data Video PV130 Browser Spectra II Figure 17.
Clovis Server 1or more PCs Router Hub 1or more PCs New York Server Router Hub PelcoNet Transmitter Data Video PV130 PELCO GENEX Genex Browser Spectra II Figure 18.
HARDWARE INSTALLATION Refer to Appendix A - Connecting PelcoNet to Different Components for diagrams that show various connections. Connecting Video Sources Or Displays • To connect a camera, plug a standard coaxial cable into the BNC connector at the front of the transmitter. You can connect any camera or other video source (for example, a VCR with a composite PAL or NTSC output). The input accepts color or black and white sources and automatically detects whether it is PAL or NTSC.
Connecting Data Terminals The unit has two serial interfaces—one at the back and another at the front. They serve different purposes and cannot be used interchangeably, as explained in the following. Control Terminal Port For local control and configuration of the unit, you can connect a data terminal (for example, a PC running a standard terminal program) to the serial interface labeled Control Terminal on the rear panel.
Transparent Data Port The second serial interface, on the unit’s front panel, offers a transparent serial data channel between the receiver and the transmitter. A typical application for the transparent data channel is remote control of peripheral equipment (PTZ functions of selected cameras, for example). You can also use this channel for remote control of any external device with a serial interface. The serial data is transferred in parallel to the video and audio data.
Connecting External Sensors and Controlling Peripheral Devices The unit has an alarm input to use for external signaling devices, like door contacts or motion detectors. You can connect switches or contacts directly without a separate power supply. The alarm input is located on the two left pins of the detachable screw terminal (see Figure 22). 1 Key: 1 = 2 = 3 = 4 = 2 3 4 Alarm input, positive terminal Alarm input, ground terminal Relay output, Y Relay output, Z Figure 22.
CONFIGURATION There are two ways to configure your system: • The most basic control and configuration is accomplished by connecting a terminal to the RS-232 terminal port. • A more complete configuration and display of video is through the built-in HTTP server, which connects to any standard web browser.
Command Reference The following table gives an overview of all available commands. (Enter the appropriate information where indicated by the quotation marks below. Do not enter the quotation marks.) Table A. Terminal Command Reference Cmd Description ? Displays the help screen. i Set up a new IP address. ->Enter new IP address (old:192.168.0.1): ‘new IP address’ [Enter] ->IP address set to s Set up a new subnet mask. ->Enter new subnet mask (old:255.255.255.
Table A. Terminal Command Reference (continued) v Display version information. >HW version: SW version: b Displays the current transmission data rate. The display is updated continuously. Configuration Using A Web Browser In addition to the aforementioned configuration using a terminal program, which only covers the most basic settings, a web browser is the tool of choice for a more complete configuration. To accomplish this, the system features a complete HTTP server.
MATRIX CONTROL** WITH LIVE VIDEO MATRIX CONTROL** WITH SERVER PUSH GENEX MUX** WITH LIVE VIDEO GENEX MUX** WITH SERVER PUSH SPECTRAfi DOME** SYSTEM WITH LIVE VIDEO SPECTRA DOME** SYSTEM WITH SERVER PUSH LIVE VIDEO** SERVER PUSH** ESPRIT ** WITH LIVE VIDEO ESPRIT** WITH SERVER PUSH VIDEO * Video quality Video resolution Bandwidth ActiveX Bandwidth RX Camera name Name stamping Time stamping Input source Output standard Enable JPEG images Time slice FTP server IP address Login name Password Path AUDI
PelcoNet Home Page Figure 24. PelcoNet Home Page The home page is the starting point for any configuration. The window in the center of the screen is the display area for decoded video. See the Typical Applications section for a description of how to display video with your browser. • Clicking on the Pelco logo on any page connects you to the Pelco Internet home page (provided the LAN supports Internet access).
Figure 25. PelcoNet Transmission System Setup Page NOTE: When changing any configuration item in one of the following pages, make sure to change a single item at a time. Then click the respective Set button. If more than one item needs to be changed, execute the procedure repeatedly. If more than one item is changed without clicking the Set button in between, only the entry associated with the clicked button is actually changed. All other entries return to their previous settings.
General Settings Configuration Page The unit ID name and address, as well as network and routing information, comprise the General Settings Configuration Page. All units have a real-time clock set during manufacture. However, time and date can be changed any time; for example, when the units are operated in different time zones. Version numbers for the hardware and the firmware are for information only. Whenever you need technical support, make sure you have these numbers ready. Figure 26.
The following table gives detailed information about the items on the General Settings Configuration Page, together with the default factory settings: Table B. General Settings Configuration Item Default Settings Name none The unit name helps the user identify a particular unit, especially if many PelcoNet Transmission Systems are on the network. ID none The ID serves as a machine-readable name. The ID can be read at any time.
Table B. General Settings (continued) Configuration Item Default Settings Mail reply address none Similar to the name field. The recipient of the e-mail will identify the sender of the e-mail by this entry. Multicast Group IP 0.0.0.0 This is the Multicast IP Address. (Network hard– ware–such as switches, hubs, routers, etc.–must support the multicasting protocol, ICMP.) This field sets PelcoNet to use the multicasting protocol, which makes for a more efficient use of bandwidth. Enable Multlink H.
Figure 27.
Video Settings Configuration Page The Video Settings Configuration Page lets you modify all video-related parameters. Some items apply only to transmitters while others require a receiver. The screen capture below belongs to a receiver: the setting for the video bandwidth and the output standard are both disabled. Refer to Table C for default settings and descriptions. Figure 28.
The following table details the configuration items. The Type column shows whether the particular setting applies to transmitters (T) or receivers (R), or both (B). Table C. Video Settings Configuration Item Default Settings Type Description Video quality super fast T On restricted bandwidth channels, the video quality preference in terms of speed versus sharpness can be selected.
Table C. Video Settings (continued) Input source camera T To facilitate the connection of video tape recorders as video sources, the input can be switched from the default camera position to VCR. VCRs require a less rigid setting of the internal PLL, due to jitter caused by the mechanical components. Output standard PAL R The video standard to be used at the output of receivers can be selected to be PAL or NTSC compatible.
Audio Settings Configuration Page Audio configuration settings apply only to transmitters and receivers equipped with the audio option (NET101T-A and NET101R-A). Figure 29.
The table below details available configuration items. Table D. Audio Settings Configuration Item Default Settings Description Audio interface Line I/O The unit features two different audio interfaces: line input and output via cinch sockets and a telephone handset interface via an RJ-11 plug. The handset interface also features DC power for the microphone. Only one of the interfaces is active at any given time, as selected by this setting.
Alarm Settings Configuration Page The PelcoNet Transmission System is not only a multimedia gateway but also a security device and, therefore, has many features related to security applications. The Alarm Settings Configuration Page lets you configure your unit for video surveillance applications. This page basically applies to transmitters only. However, receivers do provide the same features.
The set of video surveillance features is explained below. Table E. Alarm Settings Configuration Item Default Settings Description Video alarm off The signal video source (the camera in most cases) is constantly checking for availability. Should the video signal fail— due to tampering or failure of the camera or video cable—an alarm action may be triggered, if selected, as explained below. Motion alarm off The system has a video motion detection feature.
Table E. Alarm Settings (Continued) Configuration Item Default Settings Description Alarm status off Current alarm activation status can be shown in the video frame (similar to the name, date, and time stamping discussed in Table C). If configured to be on, the status of the activated alarms, namely video, motion and input, is shown in the upper left corner of the video frame. Or, the display can be activated as soon as an alarm condition is reached.
Table E. Alarm Settings (Continued) Configuration Item Default Settings Description Live video auto connect off The auto connect feature guarantees an active connection to the given alarm IP address even after connection breakdown or network failures. If auto connect is selected, the network cable can be pulled any time. As soon as the network comes back alive, the connection is reinstated. On a receiver, this feature is enabled to establish a connection to a transmitter automatically.
Interface Settings Configuration Page You can use the Interface Settings Configuration Page to configure the parameters of the RS-232 transparent data port on the front panel. The parameters of the terminal port are configured at 9600 baud, 8 data bits, no parity, and 1 stop bit. Figure 31.
The default parameters of the transparent data port agree with the most commonly used settings, as shown in the following table. Table F. Interface Settings Configuration Item Default Settings Description Baudrate 9600 Select any transmission rate from 300 to 19200 baud. Data bits 8 Select 7 or 8 data bits. Parity none Select odd, even, or none. Stop bits 1 Select 1 or 2 stop bits.
LIVE VIDEO AND SERVER PUSH VIDEO PAGES The Live Video page shows a real-time picture of the camera view with update rates and image quality similar to a box-to-box configuration. It can be configured for bandwidth use and for various image quality settings. The Server Push page shows still pictures that are updated periodically, and image quality is fixed. 1.
Figure 32.
Figure 33.
WEB BROWSER CONTROL PAGES Accessing These Pages 1. To access the PelcoNet Transmission System home page, you must first connect to the Internet/intranet network and open Internet Explorer (the browser). 2. Then, enter the default address 192.168.0.1 in the address box. If this address has been changed, enter the appropriate address. 3. On the home page, click on Control to access the Device Controls page. 4. The Device Controls page has underlined links to the control pages. To access, click on one.
Controlling The Display The live video control pages include representations of keys that let you control various functions (in addition to showing the camera display). Use the mouse pointer and click the left mouse button to enable options and operate controls on the screen. Click outside the options to disable a radio button or selection button. Live video pages let you choose the size of the video viewing area. Click either 352x288 (small) or 704x576 (large) in the Resize Video field.
Matrix Control Live Video/Server Push Page Contents Figure 35.
Genex Live Video/Server Push Page Contents Figure 36.
Spectra Live Video/Server Push Page Contents Figure 37.
Esprit Live Video/Server Push Page Contents Figure 38.
DX3016 Live Video/Server Push Control Page Contents Figure 39. DX3016 Control Page NOTE: The DX3016 control pages apply to both the DX3009 and DX3016. The DX3016 pages contain the following arrayed across the top: • “Split” buttons (16-grid, 9-grid, A, B) let you view various camera combinations. “A” displays cameras 1-4, “B” displays cameras 5-8, 9-grid displays cameras 1-9, and 16-grid displays cameras 1-16. • Two sequence buttons (SEQ, SEQ) run sequences 1 and 2.
The record/playback control buttons for the digital video recorder are arrayed directly beneath the screen. From left to right the icons are defined as follows: - This green button resets the DVR after a warning is received (for example, if a camera is disconnected). Click this button to reset the unit. Refer to the DX3000 Warning Reset Button documentation in the Troubleshooting section for a list of the warnings. - This button reverses the image one frame at a time in playback mode.
ADVANCED FEATURES Automatic Connection Feature The advantage of conventional dedicated cabling lies in guaranteed performance and availability. The PelcoNet Transmission System’s auto-connect feature is designed to provide the same level of guaranteed connectivity expected from analog coaxial video cables. IT networks commonly experience short breakdowns and congestion. Protocols used for computer communication (for example, TCP/IP) are designed to cope with missing data and interruptions.
Record and Play Back The Display On a PC Live video control pages let you record the camera display on a PC’s hard drive and play it back later. The file is recorded on the hard drive of the PC on which you are viewing the picture. The controls are a row of buttons beneath the screen. - These buttons jump the display to the beginning or ending of the recording in playback mode. - These buttons incrementally move the display backward and forward while the display is paused in playback mode.
Playing Back The Recording You can play back the camera recording either through the Windows Media Player or in PelcoNet through the browser. Do the following to play back the camera recording through the browser: 1. Access a live video control page (by clicking Control on the Home page, and then clicking one of the underlined links to a live video control page). 2. Click the button. A directory window opens. 3. Select the directory where the file you want is located.
TROUBLESHOOTING If the following instructions fail to solve your problem, contact Pelco Technical Support at 1-800-289-9100 for help. You should have the serial number from the bottom of the unit and the firmware version ready in case they are needed. Do not try to personally repair a unit. Opening it immediately voids any warranty. Leave maintenance and repairs to qualified technical personnel. Swap a defective unit with a replacement unit and return the defective one for repair.
Transmit LED The orange LED next to the Ethernet 10BASE-T connector should flash briefly whenever a unit transmits a packet (for example, when accessing the unit with a web browser). If this LED fails to come on, perform the following checks: • • • • • Are all units connected correctly with the power supply? Check power supplies and connections.
Troubleshooting Connection Problems If you fail to connect to a system from a hardware receiver, check the following to pinpoint the problem: • • Do not connect two units of the same type (for example, receiver to receiver). Make sure network connectivity is available (for example, by using the ping command as described above).
Test Between Audio-Equipped Transmitter and PC 1. Connect a microphone (via a preamplifier) to the Line-In cinch plug or connect a handset to the RJ-11 plug on the unit. 2. Make sure the correct menu items are set in the Audio Configuration Page—that is, select the appropriate interface (line in/out or handset). 3. Switch the coding mode to G.711 or G.728. 4. Select a volume above zero. 5. Connect a loudspeaker to the PC’s soundcard.
SPECIFICATIONS NETWORK PROTOCOL AND STANDARDS COMPATIBILITY Internet: IP, TCP, UDP, ICMP, ARP Configuration: HTTP, FTP Transmission Standards: H.323 (plus H.225, H.263, G.722, G.723, G.728, G.729) Video Coding: H.261, M-JPEG (M-JPEG in Server Push mode only) Video Format: CIF (352 x 288), QCIF (176 x 144) Video Frame Rate: Up to 30 images/second Audio Coding: G.711, G.728 Data Communication and Remote Control: H.
POWER ADAPTER Type: Plug power adapter Input Voltage: 100-240 VAC, 50/60 Hz Output Voltage: 5 VDC, 2A Country Specific Adapters: US (default), Australia, Europe, UK NOTE: The physical adapter for the wall outlet is interchangeable for use in different countries. The adapter snaps into the plug power supply. Contact your distributor if you need an adapter for a different country. For your own safety, do not open the power supply and never use a do-it-yourself adapter.
GLOSSARY 10BASE-T IEEE 802.3 specification for 10 Mbs Ethernet ARP Address Resolution Protocol b/s Bits per second, the actual data rate Cat5 Cable Type of cable used on a LAN to connect computers, printers, and transmitters and receivers to a hub on the network CIF Common Intermediate Format; video format with 352 x 288 pixels Default Gateway The router’s IP address (for example, 192.168.0.
JPEG Joint Photographic Expert Group (procedure to encode still images) LAN See Local Area Network Local Area Network Multiple computers linked together into a network to share information within a limited geographic area (such as a building or a campus) controlled by a network operating system and using a transport protocol MAC Address Media Access Control/hardware address NAT See Network Address Translator Network Address Translator A proposal for IP address re-use where the local IP address is
APPENDIX A – CONNECTING PELCONET TO VARIOUS COMPONENTS Connecting Pelconet To Various Components With Assorted Keyboards Connection Scenario 1 Refer to Figure 40 and the instructions that follow. Figure 40.
1. Connect a PV130 Converter to the RS-232 port on the front of the PelcoNet Transmission System receiver. The data format should be 4800 baud, 8 data bits, no parity, and 1 stop bit. 2. Connect the black and white striped wire from the power supply that comes with the converter to the converter’s +12 VDC terminal and the solid black wire to the GND terminal. 3. Connect RD(A) on the converter to terminal 2 on the wall block. Connect RD(B) on the converter to terminal 1 on the wall block. 4.
Connection Scenario 2 Refer to Figure 41 and the instructions that follow. Figure 41.
1. Connect a PV130 Converter to the RS-232 port on the front of the PelcoNet Transmission System receiver. The data format should be 9600 baud, 8 data bits, odd parity, and 1 stop bit. 2. Connect the black and white striped wire from the power supply that came with the converter to the converter’s +12 VDC terminal and the solid black wire to the GND terminal. 3. Connect TD(A) on the converter to terminal 7 on the wall block. Connect TD(B) on the converter to terminal 8 on the wall block.
Connection Scenario 3 Refer to Figure 42 and the instructions that follow. Figure 42.
1. Connect a PV130 Converter to the RS-232 port on the front of the PelcoNet Transmission System receiver. The data format should be 4800 baud, 8 data bits, even parity, and 1 stop bit. 2. Connect the black and white striped wire from the power supply that came with the converter to the converter’s +12 VDC terminal and the solid black wire to the GND terminal. 3. Connect TD(A) on the converter to terminal 7 on the wall block. Connect TD(B) on the converter to terminal 8 on the wall block.
Connecting PelcoNet To The Com Out RS-422 Port On a Genex Multiplexer Refer to Figure 43 and the instructions that follow. 00529 Figure 43. Connecting PelcoNet to Genex Using the COM OUT RS-422 Port 1. Verify that the multiplexer has Version 4.1 firmware. (The version number flashes on the monitor when power is applied to the multiplexer.) 2. Set PelcoNet’s transparent data port to 9600 baud, 8 data bits, none (for parity), and 1 stop bit if it is not so set already. This is the default setting. 3.
Connecting a PelcoNet Receiver To a System CM9502 Refer to Figure 44. This configuration lets an operator view and control cameras with a CM9505 keyboard. 9 Figure 44.
Connecting PelcoNet To a CM9502 ASCII Serial Port Figure 45. Using PelcoNet with CM9502 to Provide Remote Control Refer to Figure 45. This configuration lets an operator view and control cameras from a PC using a web browser. (The operator’s PC is not shown on the diagram.
Connecting a PelcoNet Receiver To a System CM8500D Refer to Figure 46. This configuration lets an operator view and control cameras with a CM8505D keyboard. Figure 46. Using PelcoNet with CM8505D to Provide Remote Control Connecting PelcoNet To a CM6700 And KBD200 For Remote ASCII Control Refer to Pelco Tech Tip 00-3042 for an illustration (available on Pelco’s web site). This configuration lets an operator view and control cameras with a remote KBD200 keyboard.
Connecting PelcoNet To a CM6700 ASCII Port Figure 47. Using PelcoNet with CM6700 to Provide Remote Control Refer to Figure 47. This configuration lets an operator view and control cameras from a PC using a web browser. (The operator’s PC is not shown on the diagram.
Connecting PelcoNet To CM9760 Equipment For Remote Browser Control Figure 48. Using PelcoNet with CM9760-DT to Provide Remote Control of a 9760 Monitor Output Refer to Figure 48. This configuration lets an operator view and control cameras on a PC using a web browser. (The operator’s PC is not shown on the diagram.
Connecting PelcoNet To CM9760 Equipment For Remote Communication Figure 49a. Using PelcoNet to Transmit Data and Video Between 9760 Nodes Refer to Figures 49a and 49b. These configurations let an operator remotely view and control cameras connected to the CM9760.
Pelco Manual C1977M-D (6/02) [ 83 ] Figure 49b.
[ 84 ] • • • • Pelco Manual C1977M-D (6/02) 1200 8 NONE 1 M IC RS-23 2C A LA RM IN 4 4 7 7 6 CA M ERA O UT 5 6 CA M ERA IN 5 FRAME RSD 2 TXD 3 DTR 4 SG 5 DSR 6 RTS 7 CTS 8 BAUD RATE: DATA BITS: PARITY: STOP BITS: DELIMITER: 1 2 3 4 5 6 7 8 9 GND 3 2 1 GND 3 2 1 ON 9 9 Y/ C V IDEO OUT 1200 8 NONE 1 CR OFF SCSI RESET TERMINATION SCSI 8 8 FRAME 2 RSD 3 TXD 4 DTR 5 SG 6 DSR 7 RTS 8 CTS 00670 DX3000 Figure 50.
TO NETWORK (LAN / WAN) 2-RX 3-TX 5-GND CONNECT PELCONET TO 6800 VIA RS-232 PORT PELCONET CM6800-48X8 TRANSPARENT DATA PORT COM2 2 RXD................................................... 8 TXD 3 TXD................................................... 1 RXD 5 GND.................................................. 5 GND Figure 51.
Figure 52. Manager Screen SET SERIAL PORT 07 DEVICE: TYPE: BAUD RATE: PARITY: DATA BITS: STOP BITS: ASCII RS232 9600 ODD 8 1 RETURN Figure 53.
TO NETWORK (LAN / WAN) 2-RX 3-TX 5-GND RD(A) TD(B) TD(A) PV130 ORDERED SEPARATELY RD(B) 5 4 2-RX 3-TX 5-GND Pelco Manual C1977M-D (6/02) CONNECT PELCONET TO 6800 VIA RS-232 PORT PELCONET CM6800-48X8 TRANSPARENT DATA PORT COM2 2 RXD................................................... 8 TXD 3 TXD................................................... 1 RXD 5 GND..................................................
ADDENDUM Addendum No.: Date: Manual Affected: Manual Update: ® C1977MD-ADDEN ADDENDUM Addendum No.: May 15, 2003 PelcoNet™ Transmission System (NET101) – C1977M-D In Appendix B – Frequently Asked Questions (FAQs), replace the answer to question 10 with the following paragraph.
APPENDIX B – FREQUENTLY ASKED QUESTIONS (FAQS) 1.
9. Everything is wired correctly but I do not have any control from the browser. What else could be wrong? The Transparent Data port settings should be set to match the equipment to which PelcoNet is connected. Also, in Internet Explorer, the Microsoft Virtual Machine should be enabled. To do so: on the Tools menu, select Internet Options. Then select the Advanced tab. Locate the option Microsoft VM. Place a checkmark next to Java Console Enabled and JIT compiler for virtual machine enabled.
INDEX Symbols E 10BASE-T 13, 26, 62, 63, 66, 68 E-mail alarm notification 59 E-mail message 45, 59 A ActiveX 48, 52 Alarm connect 44 Alarm input normally open/closed 43 Alarm input pin 43 Alarm IP address 44, 59 Alarm IP set command 27 Alarm message string 44 Alarm settings configuration page 42 Alarm status 44 Audio coding mode 41 Audio input level 41 Audio interface 41 Audio line in/out 23 Audio output level 41 Audio settings configuration page 40 B Baud rate 47 Bistable mode 45 Buttons for recording
M S Mail reply address 35 Mail server IP address 34 Matrix Control live video/server push page content 53 Menu tree 29 Microsoft Internet Explorer 29 Monostable 45 Motion alarm 43 Motion detection 59 Motion detection sensitivity 59 Motion-JPEG 14 Send e-mail 45 Sensitivity of motion detection 59 Serial interface terminal port 24 Serial interface transparent port 25 Server Push 14 Set button 32 SMTP server 34 Spectra live video/server push page contents 55 Status of alarm inputs 59 Stop bits 47 Subnet mas
WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • • • • • • • • • Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/MC3600 Series); two years on all other cameras. Three years on Genex® Series (multiplexers, server, and keyboard).
