ON PAN AUTO OFF MPTV151 0PAZ MANUAL TILT SPEED PAN SPEED UP LEFT RIGHT ZOOM FOC US IRIS TELE NEA R OPEN SPEED DOWN WIDE FAR CLOSE MPT1510DT and MPTV1510 Series Controllers Installation/ Operation Manual C565M-B (7/98) Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.pelco.
CONTENTS Section Page 1.0 GENERAL .................................................................................................. 3 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 3 1.2 UNPACKING INSTRUCTIONS .......................................................... 4 1.3 RECOMMENDED TOOLS ................................................................. 4 2.0 DESCRIPTION .......................................................................................... 5 2.1 MODELS .....
1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes. 2. Only use replacement parts recommended by Pelco. 3. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry.
1.2 UNPACKING INSTRUCTIONS Unpack and inspect all parts carefully. The following items are supplied: 1 1 MPT1510DT or MPTV1510 Series Controller Installation/Operation Manual (C565M-B) Be sure to save the shipping carton, boxes and inserts. They are the safest materials in which to make future shipments. If an item appears to have been damaged in shipment, replace it properly in its box and contact the factory at 1-800-289-9100 or 1-559-292-1981 for a replacement.
2.0 DESCRIPTION The MPT1510DT or MPTV1510 Series Controllers provide all the necessary electronics to implement the features below for Pelco's PT1250DC heavy duty and PT550P medium duty 115 VDC pan and tilt units. • • • • • Pan and tilt control via a joystick Pan and tilt speed control (on some models) Auto scan (on some models) Zoom lens control (on some models) Desk top or rack mount options, depending on the model The front panels on all models contain a power switch, pilot lamp, and a joystick.
3.0 INSTALLATION 3.1 OUTPUT CONNECTOR ASSEMBLY Assemble the connector parts according to the instructions below. Refer to Figure 1 during assembly. For best results use an AMP style crimper when making the wireto-pin connection. 1. Slide the connector clamp assembly over the conductor cable. If the diameter of the conductor cable is such that the rubber boot will slide over it easily then slide the rubber boot onto the conductor cable at this time. If not, discard the rubber boot. 2.
1" 1/8" FRONT VIEW 14-PIN OR 3 1 7 4 11 14 8 12 Figure 1. Output Connector Assembly Diagram Table A. Output Connector Pin Assignments Pelco Manual C565M-B (7/98) Pin No.
4.0 OPERATION Refer to Figure 2. 1. Set the power switch to the ON position to activate the controller. The pilot lamp will light when power is applied. 2. If your model has a PAN switch, set it in either the AUTO position to select auto scan (pan) or the MANUAL position to use the joystick. 3. Operate the pan function by moving the joystick LEFT or RIGHT. 4. Operate the tilt function by moving the joystick UP or DOWN. 5.
5.0 TROUBLESHOOTING If operating problems are experienced with the controller, check the fuses and the power supply cord. Next, check the condition of the output cable and its two connections. There is nothing else that can be done without the aid of proper test equipment. It is recommended that your dealer or the Pelco Customer Service Department be contacted for assistance. Refer to Section 7.0 for warranty and return information.
6.0 SPECIFICATIONS ELECTRICAL Input Voltage: 120 VAC, 50/60 Hz Maximum Power Requirements: 250 vA Power Cord: 3-wire grounded, #18 AWG Fuse Protection: Model F1 F2 F3 MPT1510DT MPTV1510DT MPTV1510CAZ MPTV1510PZ MPTV1510PAZ 1A 2A 3A 3A 3A N/A N/A 2A 2A 2A N/A N/A 0.2 A Slow Blow 0.2 A Slow Blow 0.
NOTES Pelco Manual C565M-B (7/98) 11
7.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex® Series products (multiplexers, server, and keyboard).