User's Manual

ManualsBrandsPelco ManualsVideo Gaming AccessoriesPelco pelco c06hwc

PELCO • 3500 Pelco Way, Clovis, CA 93612-5699 • (559) 292-1981 • (800) 289-9100

FAX (800) 289-9150 or (559) 292-3827

C06HWC

Pre-wired Interconnecting

Cable

Installation/Operation

Manual C940M-C (9/95)

1.0 SCOPE

The information within this manual covers the installa-

tion and operation of the C06HWC pre-wired intercon-

necting cable.

Prior to installation and use of this product, the follow-

ing WARNINGS should be observed.

1. Installation and Servicing should only be

done by Qualified Service Personnel.

2. The installation shall be done in accordance

with all local and national electrical and

mechanical codes utilizing only approved

materials.

3. Unless the cable is specifically marked “WA”

(for use in wet locations), the cable is de-

signed for indoor use only and it must not be

installed where exposed to rain and mois-

ture.

Please thoroughly familiarize yourself with the infor-

mation in this manual prior to installation and operation.

2.0 DESCRIPTION

The C06HWC is a pre-wired 6 foot cable designed for

use with Pelco hard-wire controls for pan/tilts, scanners

and motorized lenses. The pre-wired cable is supplied

with a 14-pin control connector on one end and butt

splices on the mating end for the pan/tilt or lens, allow-

ing for a quick and easy field installation. Compatible

controls are listed below:

*MLZ6DT *MLZA6DT MPT24DT

MPT24DT/220 MPTA24DT MPTA24DT/220

MPT115DT MPTA115DT MPT220DT

MPTA220DT PT506-24DT PT506-24A

PT506-24DT/220 PT506-24A/220

* Compatible only when not used with the AI700

(Auto-iris).

Summary of content (4 pages)

PAGE 1
® C06HWC Pre-wired Interconnecting Cable Installation/Operation Manual C940M-C (9/95) 1.0 SCOPE Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. The information within this manual covers the installation and operation of the C06HWC pre-wired interconnecting cable. 2.0 DESCRIPTION Prior to installation and use of this product, the following WARNINGS should be observed. 1.
PAGE 2
3.0 SPECIFICATIONS 5.0 OPERATION ELECTRICAL By using the controller, you should be able to control the pan and tilt functions of the pan/tilt and/or the focus, iris, and zoom functions of the motor operated lens. Connectors: Control side: Pan and tilt/ Lens side: Cable: 14 pins 5.1 SYSTEM TEST Butt splices 12 conductor Using the controller, operate the following functions (if applicable) and verify correct operation of each function: GENERAL Dimensions: Maximum Wire Temperature: 6 ft (1.
PAGE 3
6.0 TROUBLESHOOTING GUIDELINES 1. If none of the functions in Section 5.1 operate correctly, check the connection of the CPC connector to the control unit. 2. If the connection is loose, tighten the lock ring on the CPC connector and start the system test procedure in Section 5.1. 3. If the connections are tight, check the butt splices to determine if the splices were made correctly. If the butt splices are correctly made, there may be a problem with the control unit, pan/tilt, or lens.
PAGE 4
8.0 WARRANTY AND RETURN INFORMATION WARRANTY RETURNS Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex® Series products (multiplexers, server, and keyboard).